r/anycubic • • 4h ago

Advice Title: [FIX] Anycubic Slicer Next works on Ubuntu 26.04! Here's how to install it (possibly Linux Mint too)

0 Upvotes

I recently got my Anycubic Kobra X and wanted to install Anycubic Slicer Next on my Ubuntu 26.04 machine.

Unfortunately, Anycubic's official installer immediately rejected my operating system, claiming that only Ubuntu 24.04 is supported.

So I downloaded their installation script to see what was going on.

Turns out, the installer literally contains this:

check_os_version() { local os_version=$(lsb_release -sc 2>/dev/null) if [ "$os_version" != "noble" ]; then echo "$1" exit 1 fi }

That's it. It checks whether your Ubuntu codename is noble (24.04) and refuses to continue otherwise.

The actual installer simply adds an APT repository and installs the package.

The good news: I bypassed the installer and successfully installed Anycubic Slicer Next 2.0.0.6 on Ubuntu 26.04. It launches and works without any modifications to the application itself!

How to install it

Step 1: Add Anycubic's official APT repository

Open a terminal and run:

echo "deb [trusted=yes] https://cdn-universe-slicer.anycubic.com/prod noble main" | sudo tee /etc/apt/sources.list.d/acnext.list

We're deliberately using noble instead of the actual Ubuntu codename.

Step 2: Update your package lists

sudo apt update

You might receive warnings about a conflicting distribution or missing i386 packages. I received both, but they didn't prevent installation.

Step 3: Check dependencies before installing

sudo apt install --assume-no anycubicslicernext

Make sure APT doesn't propose removing or downgrading important system packages.

On my machine, the result was:

Upgrading: 0 Installing: 8 Removing: 0

Step 4: Install the slicer

sudo apt install anycubicslicernext

That's it! Launch Anycubic Slicer Next from your application menu.

Optional: Disable the repository afterward

Anycubic's installer uses [trusted=yes], which bypasses normal APT repository signature verification.

If you don't want to leave this repository enabled permanently, run:

sudo mv /etc/apt/sources.list.d/acnext.list /etc/apt/sources.list.d/acnext.list.disabled sudo apt update

You can re-enable it later to check for updates.

What about Linux Mint?

This method may also work on Ubuntu-based Linux Mint distributions, particularly Mint 22.x, which uses Ubuntu 24.04 as its base.

The important part is specifying noble in the repository configuration.

I have only personally tested Ubuntu 26.04, so I can't guarantee compatibility with Mint or other distributions. Check the dependency simulation before installing.

My results

OS: Ubuntu 26.04

Slicer: Anycubic Slicer Next 2.0.0.6

Package source: Official Anycubic APT repository

Dependency issues: None reported

Existing packages removed: None

Application launches: Yes

Initial functionality: Working

I haven't tested every feature, so this isn't a guarantee of complete compatibility.

A small message to Anycubic

Please stop treating "not officially tested" as "incompatible."

Your slicer works on my Ubuntu 26.04 installation without modifying the application at all. The only obstacle was the operating-system check in your installation script.

Instead of blocking newer Ubuntu versions entirely, why not display a warning that they haven't been officially tested and let users proceed at their own risk?

Hopefully this saves some fellow Linux users from unnecessarily downgrading their operating systems.

If anyone tries this on Linux Mint or another Ubuntu version, please share your results in the comments!


r/anycubic • • 7h ago

Problem HELP - Staggered/offset lines (Kobra s1)

Thumbnail
gallery
2 Upvotes

my newly bought kobra s1 started printing like this after 200 hours of print time, i already lubed the the tube rails and screws but it won't get better, is there something im missing? even after running a complete calibration nothing changes.


r/anycubic • • 8h ago

Trying to match stepper motor

Thumbnail reddit.com
1 Upvotes

r/anycubic • • 9h ago

Will there be a better price on an Ace 2 Pro on Black Friday?

Thumbnail reddit.com
1 Upvotes

r/anycubic • • 12h ago

Brand New Anycubic Kobra 3 Max V2 – Extruder Stops Feeding During Long Prints (Error 11518)

2 Upvotes

Hi everyone!

I'm experiencing a frustrating and unusual issue with my Anycubic Kobra 3 Max V2, and I'm hoping someone here has experienced something similar or can help me figure out what's causing it.

The printer is brand new — I purchased it just two days ago.

The Problem

The printer initially works perfectly. It can complete smaller prints without any noticeable issues.

However, during longer prints (usually over 3 hours), the extruder suddenly stops feeding filament.

Here's what happens:

- The printer starts normally, with good first-layer adhesion and extrusion.

- At some point during the print, filament stops coming out of the nozzle.

- The print head continues moving along the correct toolpath, as if everything is printing normally.

- I can hear the extruder motor running, but it doesn't seem to pull filament from the spool.

- After a while, the printer displays Error 11518 – "Filament clogging detected."

The strange part is that if I stop the failed print and manually select Extrude at 220°C, the extruder pulls filament and extrudes PLA normally, without any issues.

Troubleshooting I've Already Done

I've tried quite a few things to rule out common causes:

  1. Completely disassembled and thoroughly cleaned the entire print head.

  2. Cleaned and inspected the nozzle, hotend, and extruder mechanism.

  3. Checked the PTFE tube and confirmed that it's clear, with no obstructions.

  4. Cleaned the filament path using a cleaning needle.

  5. Tested different PLA filaments.

  6. Tested both with the ACE 2 Pro and without it, feeding filament directly from an external spool.

  7. Performed a full factory reset.

  8. Tested the original preloaded 3DBenchy file, without using any custom slicer profiles.

  9. Confirmed that the nozzle temperature remains around 210°C during printing.

  10. Tested manual extrusion, which works normally even immediately after a failed print.

Unfortunately, none of these steps has permanently resolved the issue.

Important Observation: The Problem Seems Related to Longer Prints

Here's the timeline of what happened:

Day 1 – Initial setup

I unboxed the printer and started printing several small objects. Everything worked perfectly.

I then attempted to print a larger figurine. Partway through the print, extrusion suddenly stopped, and the printer eventually displayed Error 11518.

After troubleshooting

I completely disassembled and cleaned the print head, checked the filament path, and performed the troubleshooting steps listed above.

After reassembling everything, the printer successfully completed 2–3 smaller prints without any issues.

I thought the problem was fixed.

The problem returned

I started printing another figurine consisting of three separate parts.

- The first two parts printed successfully.

- When I started the third and largest part, the exact same extrusion failure happened again.

This makes me suspect that the problem may be related to extended printing time, heat buildup, or an intermittent extruder issue, rather than a permanent nozzle blockage.

I haven't confirmed the cause, though.

Printer Details

- Printer: Anycubic Kobra 3 Max V2

- Firmware: 1.0.5.2

- Nozzle: 0.4 mm

- Material: PLA

- Filament feeding: ACE 2 Pro and direct external spool (tested both)

- Nozzle temperature: Approximately 210°C

- Error code: 11518 – Filament clogging detected

- Printer age: 2 days

Has Anyone Experienced Something Similar?

What confuses me most is that:

- The printer works normally for smaller prints.

- The issue seems to occur during longer printing sessions.

- The extruder motor can be heard operating, but filament stops feeding.

- Manual extrusion works perfectly immediately afterward.

- The problem happens both with and without the ACE 2 Pro.

- The printer is practically brand new.

Could this be caused by heat creep, an extruder gear slipping when hot, a failing extruder motor, an intermittent electrical connection, or a filament detection issue?

Has anyone with a Kobra 3 Max V2 encountered this behavior, particularly during prints lasting several hours?

I'd really appreciate any suggestions for diagnosing the actual cause before replacing parts or requesting a warranty replacement.

Thanks in advance for any help!


r/anycubic • • 12h ago

Question about selling Anycubic Ace Pro

0 Upvotes

Hey.. I want to sell my ACE Pro and was wondering if this would be a good place to post it, or if there's a better place on reddit to sell Anycubic accessories? I replaced it with an ACE 2 Pro, and just want to recoup some of the cost.

Thanks!


r/anycubic • • 14h ago

Problem Problemas no eixo X

0 Upvotes

Ola a todos, estou tendo este problema com a minha K3M... este barulho ocorre sempre quando ela termina a impressão ou as vezes faz a troca de filamento quando faz a purga. Também as vezes ela não consegue retornar a estrusora no pondo de origem dos eixos.

Fora isso, ela imprime normalmente.


r/anycubic • • 16h ago

I just bought an anycubic kobra 3, but it seems to be an older model. It has missing parts. I think it is a discontinued model, it bares little resemblance to ones on the website. What advice can you give me?

Thumbnail reddit.com
1 Upvotes

r/anycubic • • 20h ago

Anycubic Kobra S1 Cobra Fehler 11518

1 Upvotes

Hallo zusammen,

Folgendes Problem.

Fehler 11518 wurde angezeigt. Ich habe den Druckkopf auseinander genommen und das Hotend getauscht.
Daraufhin konnte ich wieder drucken.

Als Test das PLA Benchy gedruckt. Alles super. Bis zum Ende fehlerlos gedruckt.

Dachte das Problem wäre behoben, aber beim nächsten Druckobjekt mit dem gleichen PLA und den gleichen Einstellungen bricht er direkt an dem Punkt ab wo er losdrücken sollte erneut mit Fehler 11518 .

Ich habe alles versucht und auseinandergenommen. Ich finde einfach das Problem nicht.

Wer kann helfen?


r/anycubic • • 22h ago

Looking for a replacement vat for Anycubic Photon S

1 Upvotes

I have the Photon S, and had an issue with the vat and lost it a few months ago. I have been looking for a replacement, but every link I find on reddit is dead, does anyone know of a compatible vat? It's incredibly hard to find parts and accessories due to their naming system! Thank you


r/anycubic • • 1d ago

Advice Wanting to change to a .2 nozzle on my Kobra 2 Max

1 Upvotes

I wanted to change my nozzle on my Kobra 2 to a smaller .2 just to experiment and see what the difference is.

I know how to switch out the nozzle and I'm comfortable doing that but I'm just curious what other steps I need to take within the slicing software or anything else. I use anycubic's slicer and it is updated to the latest version.

Do I just change the profile or should I mess with the speed settings and things like that? Just need some tips on what to look for. Thanks in advance!


r/anycubic • • 1d ago

Advice Anycubic Kobra 2 Pro profile for Prusa Slicer 3

1 Upvotes

Which profile would you recommend for Anycubic Kobra 2 Pro and Prusa Slicer 3 (alpha)?

I do not find any profiles any more on Anycubic's web page. The configuration wizard from Prusa Slicer 2 does not show any Anycubic Kobra any more. And the Prusa Slicer 3 does not have a configuration assistant yet.

I'd like to give the alpha version of this Prusa Slicer a try, but I don't know whether the old profile.ini are still suitable - and I'd like to get some proper fresh profiles.


r/anycubic • • 1d ago

Kobra 3 max z axis stabalizer washer size

1 Upvotes

Does anyone have the size of the spacer that goes on the bottom of the z axis stabalizer bars???


r/anycubic • • 1d ago

Advice Is this FEP still good ?

1 Upvotes

I'm new to resin 3d printers and I got a used spare vat that came with a FEP still mounted.
Is the film still good for use?
If still good, will those wrinkles show up on the prints??


r/anycubic • • 1d ago

I feel like I got scammed….

Thumbnail
gallery
0 Upvotes

Just got this Kobra Plus and 9 rolls of PETG and 4 total print beds for $100 (I know the material is worth more but still) the bed doesn’t heat at ALL, throws an error message no code, the print head does NOTHING no heat no light only moves, is there something I’m missing? Maybe like a factory reset or something? I’m new to 3D printing so please go easy on me😭


r/anycubic • • 2d ago

Help

2 Upvotes

Any idea on why it’s making this awful noise when the bed rises? It prints fine just makes this awful sound.


r/anycubic • • 2d ago

Project My first-ever 3D keychain model🥰

Thumbnail
gallery
3 Upvotes

Hi guys! 😊 I finally designed and uploaded my very first 3D keychain model today! ✨
If you have a quick minute, I'd be super grateful if you could leave a rating or a comment — your feedback is super important to me right now.


r/anycubic • • 2d ago

ACE pro and carbon fiber filament

1 Upvotes

I bought a second ACE Pro to modify and use strictly for abrasive filaments.

Does anyone know which parts typically wear out or fail when CF/GF filaments pass through it?


r/anycubic • • 2d ago

Problem Anycubic Kobra 2 Pro print quality dropped & failing at the top – should I replace the hotend?

Thumbnail gallery
1 Upvotes

r/anycubic • • 2d ago

Question Auto-fill on non-Pro M7

1 Upvotes

I have the non-pro Anycubic M7 & am curious about purchasing their resin Auto-fill system. The mental image I have of sending a job to the machine wirelessly from the slicer then having it fill itself & run the job seems really convenient in my head. I'm concerned that without the Pro's fancy heating & mixing vat that I wouldn't save any time/effort becuase I'd still need to stir up the vat (if I'm leaving resin in it), shake up the jug, switch on the heater if necessary, switch on the vent fans, etc. Also the one thing I keep running into with this hobby is that it always instantly punishes skipping steps. Does anybody have any experience with running the auto-fill system on the M7 or any other printer without the self-mixing stuff?


r/anycubic • • 2d ago

Kobra x. Printing air

1 Upvotes

So over all 1200 hours in my x has been great.

Ive had to swap some parts all handled by customer support.

And 90% of the time it just works.

I do have some ace 2 feeding issues and cannot use the 4th slot however.

So ive been trying to print an army of mini ducks for my daughter for her to do a Xmas gift for someone.

I have tried 4 different files, simplified, fixed, lowered the # of items down.

And I keep having issues, feeds I can't blame on the files.

Each file initially prints well then I have an ace feed issue.

The on the 2nd or third attempt it just prints air. Its moving, its fed, but doesnt extrude.

So i test with a benchy, it prints fine, back to ducks, and I get air.

How is the new firmware for everyone?

My understanding is my issue is probably gcode based but I wanted to ask around here before throwing this project in the trash.

update

Did a full recalibration

Found a 5th file. Did not alter it in any way. Only 20 ducks. Eliminated the ace and direct fed.

It loaded the filament and then started printing air.

So i took the same file and and made some of the adjustments to layers and infill etc as suggested. Again printed air.

Pulled a random file to test print capability. And it printed just fine.

So it seems to be an issue with my printer attempting to print 20+ small objects at a time.

Im going to try putting the gcode into ai to see if it can find the issue.


r/anycubic • • 2d ago

Why can't i select the filament i want?

Post image
1 Upvotes

when i want to print something, for some reason i can't select any other filaments unless i delete them to make the show up as the first filament on the list.


r/anycubic • • 2d ago

Problem commande incomplète

Thumbnail reddit.com
2 Upvotes

Hi everyone.

I just received my Anycubic Photon P1—which I paid extra for, specifically to include the two-compartment build plate—but to my surprise, it wasn’t in the package.

I’ve already checked my emails, my account, and so on, and there’s no other tracking number or any indication that a second package was sent.
Currently, on the "Shop" app, the Anycubic website, and PayPal, the status is listed as "order delivered and completed."

Has this happened to anyone else?


r/anycubic • • 2d ago

Anycubic support

Thumbnail reddit.com
0 Upvotes