Hi everyone!
I'm experiencing a frustrating and unusual issue with my Anycubic Kobra 3 Max V2, and I'm hoping someone here has experienced something similar or can help me figure out what's causing it.
The printer is brand new — I purchased it just two days ago.
The Problem
The printer initially works perfectly. It can complete smaller prints without any noticeable issues.
However, during longer prints (usually over 3 hours), the extruder suddenly stops feeding filament.
Here's what happens:
- The printer starts normally, with good first-layer adhesion and extrusion.
- At some point during the print, filament stops coming out of the nozzle.
- The print head continues moving along the correct toolpath, as if everything is printing normally.
- I can hear the extruder motor running, but it doesn't seem to pull filament from the spool.
- After a while, the printer displays Error 11518 – "Filament clogging detected."
The strange part is that if I stop the failed print and manually select Extrude at 220°C, the extruder pulls filament and extrudes PLA normally, without any issues.
Troubleshooting I've Already Done
I've tried quite a few things to rule out common causes:
Completely disassembled and thoroughly cleaned the entire print head.
Cleaned and inspected the nozzle, hotend, and extruder mechanism.
Checked the PTFE tube and confirmed that it's clear, with no obstructions.
Cleaned the filament path using a cleaning needle.
Tested different PLA filaments.
Tested both with the ACE 2 Pro and without it, feeding filament directly from an external spool.
Performed a full factory reset.
Tested the original preloaded 3DBenchy file, without using any custom slicer profiles.
Confirmed that the nozzle temperature remains around 210°C during printing.
Tested manual extrusion, which works normally even immediately after a failed print.
Unfortunately, none of these steps has permanently resolved the issue.
Important Observation: The Problem Seems Related to Longer Prints
Here's the timeline of what happened:
Day 1 – Initial setup
I unboxed the printer and started printing several small objects. Everything worked perfectly.
I then attempted to print a larger figurine. Partway through the print, extrusion suddenly stopped, and the printer eventually displayed Error 11518.
After troubleshooting
I completely disassembled and cleaned the print head, checked the filament path, and performed the troubleshooting steps listed above.
After reassembling everything, the printer successfully completed 2–3 smaller prints without any issues.
I thought the problem was fixed.
The problem returned
I started printing another figurine consisting of three separate parts.
- The first two parts printed successfully.
- When I started the third and largest part, the exact same extrusion failure happened again.
This makes me suspect that the problem may be related to extended printing time, heat buildup, or an intermittent extruder issue, rather than a permanent nozzle blockage.
I haven't confirmed the cause, though.
Printer Details
- Printer: Anycubic Kobra 3 Max V2
- Firmware: 1.0.5.2
- Nozzle: 0.4 mm
- Material: PLA
- Filament feeding: ACE 2 Pro and direct external spool (tested both)
- Nozzle temperature: Approximately 210°C
- Error code: 11518 – Filament clogging detected
- Printer age: 2 days
Has Anyone Experienced Something Similar?
What confuses me most is that:
- The printer works normally for smaller prints.
- The issue seems to occur during longer printing sessions.
- The extruder motor can be heard operating, but filament stops feeding.
- Manual extrusion works perfectly immediately afterward.
- The problem happens both with and without the ACE 2 Pro.
- The printer is practically brand new.
Could this be caused by heat creep, an extruder gear slipping when hot, a failing extruder motor, an intermittent electrical connection, or a filament detection issue?
Has anyone with a Kobra 3 Max V2 encountered this behavior, particularly during prints lasting several hours?
I'd really appreciate any suggestions for diagnosing the actual cause before replacing parts or requesting a warranty replacement.
Thanks in advance for any help!