Hi everyone,
I’m based in Dublin, Ireland, so just to clarify upfront, this is an Irish/UK-style domestic heating system, not an American setup.
I’ve been having ongoing problems with my hot water and would really appreciate some advice from anyone familiar with these systems. I’m not particularly knowledgeable about plumbing or heating, so apologies if I misuse any terminology.
My setup:
Gas boiler: Glow-worm Energy 18s.
Hot-water cylinder: Large blue insulated storage cylinder with an electric immersion heater.
Motorised valves: Three Myson Power Extra valves, one apparently labelled “HOT”, which I believe controls the hot-water circuit.
Cylinder thermostat: Orange thermostat attached to the side of the cylinder.
Timer: Optimum mechanical 24-hour timer, located underneath the gas boiler.
Room thermostat: IMIT dial thermostat.
As far as I understand, the system should allow us to heat our domestic hot water using either the gas boiler or the electric immersion heater.
The original problem:
We previously had issues with our hot water, and a technician came out and worked on the system. Afterwards, we could heat the water using either electricity or gas.
However, the electric immersion heater has since stopped heating the water properly. Turning on the usual electrical switch no longer produces hot water.
More recently, another technician came out and said the gas boiler should be able to heat the cylinder. He noticed that the cylinder thermostat was set relatively low, so he increased it. He also showed me which pipe should carry hot water towards the cylinder.
Unfortunately, that hasn’t resolved the problem.
What I’ve observed while troubleshooting:
1. The gas boiler works and the radiators get extremely hot.
When I turn on the gas boiler and central heating, the radiators heat up normally. They’re practically piping hot, so the boiler is clearly producing heat.
However, the domestic hot water remains barely lukewarm, even after leaving the heating running.
2. The pipe leading towards the cylinder gets hot at the top but progressively cooler further down.
There’s a copper pipe connected to the motorised valve labelled “HOT”.
The pipe near the motorised valve gets very hot, but as it travels down towards the blue hot-water cylinder, it becomes progressively cooler. The lower section near the cylinder is only lukewarm.
I don’t know whether this is normal or whether it indicates that hot water isn’t circulating properly through the cylinder’s heating coil.
Another pipe enters the cylinder from the top, but that one doesn’t appear to be getting hot either.
3. The motorised valves have AUTO and MAN settings.
There are three white Myson Power Extra motorised valves.
Two were set to AUTO, while the valve labelled HOT was set to MAN.
I experimented with switching the HOT valve from MAN to AUTO and then back again, but it didn’t seem to make any difference.
I also noticed that the little grey levers on the valves move with practically no resistance.
The red/orange indicator light on the HOT valve is illuminated when the heating is running.
I’m wondering whether the valve might be faulty, stuck, or not opening properly.
4. The hot-water cylinder itself doesn’t seem to be heating.
Even after running the gas heating for a while, the blue cylinder doesn’t feel noticeably warmer, and the water coming from the taps remains barely lukewarm.
5. The timer appears to be permanently ON.
There’s an Optimum 24-hour mechanical timer underneath the gas boiler.
Its selector is set to “I”, which I understand means permanently ON, bypassing the programmed schedule.
I’m not certain whether this timer controls the boiler, hot water, or another part of the system.
6. The electric immersion heater also doesn’t work.
This is the part that confuses me most.
If the issue is a faulty motorised valve preventing the gas boiler from heating the cylinder, wouldn’t the electric immersion heater still work independently?
The immersion previously heated the water using a wall switch, without needing the gas central heating.
Now neither method seems to heat the water properly.
This makes me wonder whether there could be a shared issue with the cylinder, its controls, or the delivery of hot water to the taps, rather than simply a faulty motorised valve.
My questions:
Does the temperature difference along the pipe suggest a faulty motorised valve or poor circulation through the cylinder?
Is it normal for the Myson Power Extra manual levers to move with almost no resistance?
Could the cylinder thermostat or heating controls explain why the gas boiler isn’t heating the stored water?
What could explain both the gas heating and electric immersion failing to provide properly hot tap water?
Are there any simple, safe checks I can carry out before paying for another technician?
I’ve already had someone inspect the system, but unfortunately the problem persists.
I’ll attach photographs of the boiler, cylinder, motorised valves, thermostat and timer.
I’m not planning to interfere with any electrical wiring, gas components or plumbing valves myself. I’m mainly hoping to understand what might be happening and what I should ask the next technician to investigate.
Any advice would be greatly appreciated. Thanks!