r/hobbycnc • • 1h ago

My first CNC mill. How did I do?

Post image
11 Upvotes

I got this fully converted Dyna Mite 2400 for $1,000 on marketplace. Came with a 3/4 in plate steel cable and a plexiglass enclosure (plus all the original hardware that was swapped out and manuals). Just tested all the functions in the win95 laptop it came with via TurboCNC and everything is perfect. Plan is to run it on a modern-ish laptop with LinuxCNC remotely orchestrated with Claude Code. Good buy?


r/hobbycnc • • 9h ago

Built a 70kg, 12cm-thick acoustic enclosure for my Makera Carvera Z1 Pro. Janky look, but the upstairs neighbors can't hear a thing!

35 Upvotes

Hey everyone,

I usually pride myself on making things look clean and professional, but this time my priorities were strictly budget and peace of mind. My workshop is in my garage/basement, directly underneath another family's kitchen. To avoid any noise complaints, I’ve already soundproofed the entire room, but since a CNC mill is a different beast, I needed an extra layer of protection.

Instead of spending €500+ on a commercial solution or buying brand new materials, I managed to keep the total cost down to just €150 by sourcing everything else from scrap material I was originally supposed to throw away. For now, this is what I can afford, and it gets the job done perfectly.

The result is a massive, 70 kg (154 lbs) beast of an enclosure for my Makera Carvera Z1 Pro. It took me 15 hours of labor and 10 full tubes of silicone to seal every single gap.

Despite looking like a backyard DIY project, the acoustic and vibration engineering inside is pure overkill to keep the neighbors happy:

• 12 cm Thick Walls: Built as a double-walled "box-within-a-box" design with an air gap, acoustic foam pyramids, and a mass-loaded lead vinyl panel for heavy soundproofing.

• The Door: Packed with 6 cm of high-density fiberglass (60 kg/m³) and fitted with a heavy 10 mm tempered glass viewing window.

• Vibration Control: Mounted on heavy-duty anti-vibration feet to prevent the CNC movements from shaking the ceiling and transmitting structure-borne noise to the apartment above.

• Air Intake & Exhaust: The next and final step is building the baffled air intake and exhaust vents, which will also be fully wrapped in soundproofing material to ensure airflow without letting any noise escape.

Combined with the room insulation, it’s definitely not the prettiest thing I’ve ever built, but it saved me a fortune, recycled a ton of waste, and keeps the peace in my building.

Happy to answer any questions about the build!


r/hobbycnc • • 11h ago

DIY Pendant

11 Upvotes

Building a wireless CNC pendant — looking for feedback

I'm working on a DIY wireless CNC pendant using an ESP32-S3 with a 5-inch touchscreen, a rotary encoder, and physical buttons for jogging and machine controls.

I'm considering switching from nRF24L01 to Bluetooth BLE to simplify the hardware and free up some GPIO pins.

Still working on the enclosure design and button layout.

Has anyone built something similar? I'd be interested to hear your experience, especially with Bluetooth reliability and jogging controls.


r/hobbycnc • • 1m ago

PureCutCNC v0.6.0

Thumbnail
youtube.com
1 Upvotes

PureCutCNC v0.6.0 is out. In this release I added multi face (top/bottom/around) design and machining, support for 4th axis (rotary), experimental support for plasma machines, option to overcut into the spoilboard for the cutout operation. There are also many internal improvements in the toolpath calculation and simulation rendering. It is available for free download at https://purecutcnc.github.io/


r/hobbycnc • • 2h ago

Newbie Help needed

Thumbnail reddit.com
1 Upvotes

r/hobbycnc • • 17h ago

My my laser keep doing this

Thumbnail
gallery
7 Upvotes

It's cut horizontally fine but on vertically it's leaving little veneer uncut like paper thin i already checked the level it's not unbalance it flat ply it's really frustrating it's cutting nice in this setting if I do more pass they ply is getting burn (using air assist yet trying to find a diy alternative for pump)


r/hobbycnc • • 22h ago

Adding Bits to Kiri Moto

Post image
5 Upvotes

Hi folks, QQ,

Can someone help me with adding bits to KiriMoto? at the moment im trying to ad NJ3.2001 a 20 degree V bit, But i tried adding the measurements and they dont seem to play super nice? any time i add in the flute length it auto changes the angle, and visversa.

could anyone familiar with KiriMoto give me some advice and let me know if this looks right?


r/hobbycnc • • 14h ago

Image to line cutting

Thumbnail reddit.com
0 Upvotes

r/hobbycnc • • 17h ago

Update: Z1 Pendant App walk through + New Features Added 3d Probing, Run Job, File manager + more

Thumbnail
youtu.be
1 Upvotes

r/hobbycnc • • 12h ago

Built an Android app suite for hobby CNC routers: offline AI photo-to-3D carving relief, 2.5D signs, 3D terrain STLs, and PCB isolation milling DXFs right on your phone

0 Upvotes

Hi everyone! Just to be clear: I am not a software company. I'm just one guy whose hobby is CNC routers, 3D printers, and lasers, and I built these three Android apps by myself so I could design parts right at my machine without opening a PC or paying monthly CAD subscriptions.

  1. Sphyron Cad: Landscapes (100% FREE - No Ads, No Account) Frame any mountain, island, or city on Earth and export a framed 3D terrain & building model (STL/OBJ) for 3D printers & CNC routers, stacked 3mm laser-cut contour layers (DXF/SVG), or 70x50 cm vector posters in 13 themes.

  1. Sphyron CAD (84+ Parametric Parts & Offline AI Photo-to-3D CNC Relief) Type your caliper dimensions to generate water pump impellers, 1:5 planetary gearboxes, spur gears, sliding-lid laser boxes, lamps, and stencil signs with 1.6mm letter bridges (STL, 3MF, OBJ, DXF, SVG). Also runs a 100% offline AI depth model on your phone to turn any photo into a 1,100,000-triangle 3D CNC relief or backlit lithophane! (5 free exports, then a single one-time unlock).

  1. Sphyron Cad: Circuit Breaker (Mobile 3D PCB Design & CNC Milling DXF) Place from 366 components (ESP32, Arduino, TMC2209, relays), route 45-degree copper tracks by touch, inspect your populated board in 3D (and export a free 3D STL to check enclosure fit), and export Gerber X2 + drill ZIPs, BOM/CPL, or CNC V-bit isolation milling DXFs.


r/hobbycnc • • 1d ago

Genmitsu 3020

2 Upvotes

This is for anyone who has or has had a genmitsu 3020.

I’ve had this router for about 2 months now and it’s been working pretty good, I haven’t made a whole lot with it but the finish has been good on the parts I’ve made(mostly carbon fiber). My only gripe is that in between tool changes and when I go to switch the op, x and y zero decide to piss off to a random spot and not where I originally set them. It doesn’t do this everytime but I’d say 50 percent of the time.

Does anyone else have this problem and is there a way to fix it or make it happen less?


r/hobbycnc • • 1d ago

Ways to detect an error in stepper drivers or motors?

0 Upvotes

In the ongoing redesign of a home grown control system controlling Avid hardware, I am trying to reuse as much of the existing system as possible to avoid costs. That said I am reusing stepper online DM860T stepper drivers (version 1.0). From a machine safety perspective one of the very bad things that could happen is one of the drivers or motors fails in the middle of a job. To identify that error if it occurs, I have many ideas with my two favorites being a voltage check at the driver which would catch any issues with the feed power but would miss any problems with the driver itself (version 1.0 drivers have no error code) or a broken wire in the motor cables. The second option is to use Hall effect sensors on the output of the stepper drivers. If there is no current then either the driver is dead or there is a wiring issue or the motor is dead. Using Hall effect sensors is the most comprehensive solution BUT I can't find where this has been done by anyone else.

So, do any of you know of someone who has used Hall effect sensors to determine the health of the drivers/motors and/or do you have different ideas that I have not thought of?

P.S., of course the "correct" way to do this is to have a closed loop control system but since I am trying to reuse existing parts that are open loop I have moved that option to the end of the list as it is the most expensive.

P.P.S,I am hoping for a comment from u/Alina_MakersChest as I always find comments from them helpful.


r/hobbycnc • • 1d ago

Compressed air flow rate of ATC spindles?

3 Upvotes

Hi all. Most ATC spindles use compressed air for tool change, but also for the purge air / air seal, which keeps stuff from getting into the bearings. I had little success in finding flow rate specs. Has anybody of you checked the air consumption at some point? I'm primarily wondering about the purge air, since this is a continous draw of compressed air.


r/hobbycnc • • 1d ago

Oh boy, what am I even doing? 😭

Thumbnail gallery
1 Upvotes

r/hobbycnc • • 1d ago

Ring Magnet absolute magnetic encoder

1 Upvotes

I want absolute shaft angle of a stepper motor connected to a gearbox. i cannot encode the rear shaft as that would require a homing sequence and dont want that.....can i consider putting a dimetrically magnetized ring magnet on the output shaft and using a say MT6701 encoder parallel to axis of the ring??


r/hobbycnc • • 1d ago

Looking for machine recommendation for cutting metal for home hobby use.

0 Upvotes

Looking to get into cnc fabrication for hobby/fun, and am looking for machine recommendations. Space is home interior basement. I’d like to mostly machine aluminum and later possibly harder metals, mostly small parts, gears and various structural parts for like robotics, rc cars/planes etc. I’d like to be able to make threads as small as M3, and things like herringbone gears with 95mm+ bores. So while that might suggest a smaller work area I would also like to potentially have larger for single piece exteriors. I have a spare 220v dryer plug on an obviously isolated breaker and other 120v isolated breakers for dust collection and compressor. While there are lots of options to choose from, I’d rather avoid buying and then upgrading a bunch of parts, and would prefer just a good enough machine from the manufacturer.

Things I know I don’t know yet:

    1. How desirable is ATC? I mean you obviously don’t need it, but does it make life that much better? I imagine most parts will end up begin a multi-tool job.

  • 2. How desirable is an enclosure? Probably won’t care much about the noise (I say this now) but more the metal shavings.

  • 3. Nice study bench or manufacture's legs packages? Enclosure answer might impact this.

  • 4. I don’t have a good idea of how long it takes these machines in general to make parts. I don’t need business speeds, but I’d rather not die of old age waiting either. I’ve seen upwards of 2.2kmm feeds and 6mm doc with ¼” single flutes on the shapeoko on aluminum, that seems pretty fast to me for roughing.

  • 5. When does mql/misting become recommended, and when required? Can you get away with just air? It appears that you can, but looking for opinions/confirmation.

  • 6. Does closed loop really help if you’re running conservative cuts?

I’ve looked at and am leaning towards, and yes quite a bit of a price and work area difference:

    1. Gnemitsu 3030-PROver Ultra, 710w spindle up to 30k rpm, ~300 × 300 × 78 mm work area.

  • 2. Shapeoko 5.1 Pro 4x2 with 65mm (120v) or 80mm vfd (220v)

  • 3. AltMill MK2 2×4 kit, 2.2kW spindle or ATC spindle (lose a little work area with this)

I’ve read a bunch of reviews on these machines and they all seem pretty positive. Cutting It Close’s comparison of the latter two was updated to say he found a loose screw and after tightening it the shapeoko and altmill had the same rigidity, a complaint I’d read elsewhere.


r/hobbycnc • • 1d ago

Considerations for Designing and Building a Homemade CNC

0 Upvotes

Having looked at the market, I have come to the unfortunate conclusion that a lot of small CNCs are simply outside of my budget. I have been thinking of building a CNC from scratch for a while now, but I have some reservations. The actual building and design should not be a major issue as I have decent CAD experience, and some limited welding experience which I can build upon. I am more concerned with the programming side and how this can be controlled. Has anyone here ever programmed their own CNC, and what exactly does it take?


r/hobbycnc • • 1d ago

Would the Piccola CNC be a good first desktop CNC for a newbie?

6 Upvotes

I know it’s still running on Kickstarter so there’s all the caveats/risks associated with that, but I’m curious if based on their advertised feature set it would be a good potential first desktop CNC for me.

https://www.piccolacnc.com


r/hobbycnc • • 1d ago

Starting shop

Thumbnail reddit.com
0 Upvotes

All opinions are valueable!


r/hobbycnc • • 2d ago

Bar display window

Thumbnail
gallery
24 Upvotes

6 mm plywood lamellas, light walnut paint


r/hobbycnc • • 1d ago

Spindle Reccomendations

2 Upvotes

I have taken the advice from here and I ended up ordering a 3030 with the 710W spindle. I am going to play around with the stock spindle for a bit while I wait for a 1.5kw spindle to arrive. So anyone have any reccomendations for which ones to get there is so many available its hard to choose. Such as air or water cooled and branding. I am in Australia so shipping is a big thing seems to cost a mammoth amount to get anything over here. Chinesium spindle is where I am looking atm.


r/hobbycnc • • 1d ago

ADVICE NEEDED

0 Upvotes

Hi I’m 24M from India and I run a small business of Paints. Now, I want to learn CNC from scratch. I don’t have a huge budget so can I try out with starter sets to understand basics of CNC

I have no background in engineering and coding I would also appreciate advice on that if it’s necessary.

Shall I try these options

  1. Twotrees TTC3018 Pro CNC Router Machine

  2. Creality Falcon 10W Laser Engraver Cutter – High Precision CNC Laser Engraving Machine

  3. CNCTOPBAOS 1610 PRO 3 Axis CNC Router Engraver Machine w/Offline Controller

Besides what are the things should I keep in mind
And what do I need to learn. Any kind of advice or discussion is appreciated.


r/hobbycnc • • 1d ago

ADVICE NEEDED

1 Upvotes

Hi I’m 24M from India and I run a small business of Paints. Now, I want to learn CNC from scratch. I don’t have a huge budget so can I try out with starter sets to understand basics of CNC

I have no background in engineering and coding I would also appreciate advice on that if it’s necessary.

Shall I try these options

  1. Twotrees TTC3018 Pro CNC Router Machine

  2. Creality Falcon 10W Laser Engraver Cutter – High Precision CNC Laser Engraving Machine

  3. CNCTOPBAOS 1610 PRO 3 Axis CNC Router Engraver Machine w/Offline Controller

Besides what are the things should I keep in mind
And what do I need to learn. Any kind of advice or discussion is appreciated.


r/hobbycnc • • 1d ago

HERE SOME HELP NEEEDED!!!

Thumbnail reddit.com
1 Upvotes