r/diydrones • u/AdBrilliant5108 • 6h ago
r/diydrones • u/AircraftExpert • 10h ago
Question Advanced electrical side courses and tutorials?
I am trying to debug some power (voltage and amperage) measuring issues on my DIY drone. My mechatronics and EE knowledge is fairly basic from two undergraduate and one graduate class, taken before the times of quadcopters.
So I need to get up to speed on the finer points of power distribution , ESCs and flight controller interaction with such. Ideally using an older Pixhawk as the example platform since this is what I am using for my drone.
r/diydrones • u/Turbob8868 • 13h ago
Good starter projects for drones
My dream is to make a drone that can be flown with a controller, but im a bit confused on how to make it. what coding language do i have to learn, and what different things do i need to buy, because i dont want to pay too much for this. But if you guys think that as a 1st personal project making a drone is a bit too much, give me some other good ideas for a personal project that I can make for my 1st project.
r/diydrones • u/Firm-Luck2062 • 16h ago
Build Showcase Ho creato una sala di controllo per sciami di droni: spettacoli di luci, missioni di ricerca, volo manuale e 16 visuali da telecamera in un'unica finestra. Demo nel tuo browser
r/diydrones • u/Ren09UAV • 18h ago
Correction to my post yesterday: diagonal arms offset by ~10 cm on a 10 kg Quad X. Does it matter?
Hey everyone,
I posted yesterday about a ~2 mm asymmetry on our quad, but I got the numbers wrong after checking the CAD properly, so here's the corrected version. Thanks to everyone who replied!
Setup (student team, water-drop mission):
- ArduCopter on a Pixhawk 6X
- T-Motor A6-M, 23" props, ~915 mm wheelbase, folding arms
- ~2.2 kg of water in two tanks (one each side), dropped mid-flight
- Hover ~51 % throttle, capped at 80 %
What the CAD actually shows:
- All four motors are exactly 321 mm from the centre, so the motor positions are symmetric.
- But each diagonal arm is offset by about 10 cm (99 mm) from the opposite one, so the arms don't run along the same axis through the centre.
My understanding is that ArduPilot only cares about where the thrust acts, so with symmetric motor positions, tuning shouldn't be affected and this is mainly a structural question (extra load at the arm mounts).
Questions:
Is that right, or can offset arms affect tuning or stability in practice?
Structurally, is this a problem worth redesigning, or is it fine as long as the arm mounts are strong enough?
With the weight dropping ~22 % after release, is it best to tune empty first and then add payload in steps?
Thanks!
r/diydrones • u/xLightbeamz • 19h ago
Question Help with AIO FC - Motors Twitching?
Hi everybody. You are probably playing GTA VI at this moment, so sorry to bother you. I’m wrestling with my very first 2.5” build. I really need your guys help.
I know my soldering can be way way WAY better, but what is happening here and is it correct that my ESC is cooked? I checked all the small chips and their tiny solder joints seem fine, although I might have touched some.
One of the four motors is running normally. However, if I push throttle on the other motors, they will vibrate (no reaction on throttle) and the ESC will go beep and they completely stop once I push throttle even more. Pretty sure I fucked something up completely.
I tested the ESC and all joints show around 0.47 resistance, so I guess no mosfet issue or whatsoever.
Please help me.
PS. I’m waiting on a TS101 soldering iron with some decent tips. Mine are all oxidised and bulky. Hopefully it will slightly boost my soldering skills. If you have any tips on this, feel free to share.
Thanks a lot ❤️
r/diydrones • u/pokemonguy0417 • 23h ago
Question How to modify this controller into an fpv controller?
Note this is the controller of the sky hunter drone that was destroyed in this sub
r/diydrones • u/PartyPollution1061 • 1d ago
Question Is there a decent-looking foldable drone with an open flight stack (ArduPilot/PX4) and a real gimbal, or do I just have to build one?
I've been looking into this for a while and keep hitting the same wall, so I'd like to hear from people who have actually built or flown something like it.
What I'm after is a drone that runs ArduPilot or PX4 (or at least has an open flight controller I can talk to over MAVLink), folds into a backpack, and carries a stabilized camera that's actually good. GPS is a given, and obstacle sensing would be a bonus. I'd like it to look like a finished product rather than a bench kit. The budget is about US$750 all in, import costs included. I'm in Brazil, where duty adds roughly 60% on top of the price.
What I've found so far:
- DJI, Autel and Potensic look right, but the firmware is closed.
- The Holybro X500 v2 and X650 and the Amovlab F410 are properly open, but they're dev kits with no gimbal (the X650 at least has folding arms).
- The Yuneec Mantis folds and has a gimbal, but as far as I can tell its PX4 is a custom build with no MAVLink access, so it doesn't help.
- ModalAI Starling, Freefly Astro and Aurelia are the right idea, but they start at several thousand dollars.
Is there anything between those? A folding frame that takes a Pixhawk-class controller and a small gimbal without looking like a science project, a small brand I haven't heard of, or a build someone has documented? I'd rather assemble from a kit than design a frame from scratch.
If I got any of the above wrong, please tell me.
r/diydrones • u/Basic-Screen2051 • 1d ago
Hello everyone, I am currently experiencing an issue involving a "rippling" effect (caused by the rolling shutter mechanism/image distortion).
Hello everyone. I am currently looking for a camera for my Raspberry Pi 4. I have been using an IMX704-based camera, but it produces a "wavy" (rolling shutter/distortion) effect in the footage, and it sometimes fails to focus—even after I disabled the autofocus feature. I’ve also discovered that the drone experiences high-frequency vibrations; while these don't significantly affect the drone's flight stability, they do impact the camera. I tried adding rubber vibration dampeners, but that didn't solve the problem. I am now considering switching to a Global Shutter camera. If anyone has experience with this, I would greatly appreciate your guidance. Thank you very much!

r/diydrones • u/igluuuu • 1d ago
Help with hdop
Hello, I'm working on this drone which is my engineering project. Right now I'm trying to make it fly with INAV POSHOLD setting as it seems as the best choice for automatic flight using rpi as its companion computer. While testing it I noticed that my HDOP value is around 1.4 which is not great. Do you have any piece of advice for me as a newbie in drones on how to make it better? I'm fighting with problem of my drone "bouncing" in height while flying. Is it connected to HDOP or something else?
EDIT: I blew some air on barometer and I saw a lot of spikes while doing it, could this be the problem?
r/diydrones • u/Nation_Drone_Repair • 1d ago
Guide Drone Firmware Updates: Install Now, Wait a Few Days, or Skip This One?
r/diydrones • u/Ren09UAV • 1d ago
How much frame asymmetry is too much on a heavy-lift quad? (~3 mm on a 10 kg Quad X)
Hey everyone,
Student team here, building a 10 kg Quad X for a water-drop mission:
- ArduPilot on a Pixhawk 6X
- T-Motor A6-M, 23" props, ~915 mm wheelbase, folding arms
- ~2.2 kg of water in two tanks (one each side), dropped mid-flight
- Hover ~51 % throttle, capped at 80 %
In CAD the motors are ~321 mm from centre, but there's about a 2 mm difference between them, so the X isn't perfectly symmetric.
My understanding is that the flight controller compensates small imbalances and AutoTune works from the measured response, not the geometry, so 2 mm (~0.6 % of the arm) shouldn't matter.
For those who've built heavy-lift or payload drones:
At what point did frame asymmetry or CG offset start causing tuning or stability issues for you?
With the weight dropping ~22 % after release, did you tune at full weight and check it when empty, or something else?
Thanks!
r/diydrones
•
u/jamesrelish
•
1d ago
Build Showcase I designed an open source 4" long range drone frame (all files on GitHub)
I've been flying this for over half a year in different conditions and environments and finally decided to release it. It's a 4" durable long range drone frame made for more extreme conditions.
Features:
- 0-30° camera angle, fully protected with no props in view
- 20x20 M3/25.5x25.5 M2 stack and vtx mounting
- frame weight is about ~65g, it's not lightweight, but it is strong (4mm thick arms, 2mm plates)
Everything can be found on the GitHub. For carbon plates I added DXF and step files. STL files for the TPU and other components such as battery pad, assembly guide and my Betaflight tune.
Makerworld: Makerworld-Memory-Halo-4
GitHub: Memory-Halo-4-Long-Range-Drone-Frame
I would love feedback and in case you build one yourself, definitely show me!
r/diydrones • u/hakoniwalab • 1d ago
Update: you can now run unmodified PX4 on an emulated Pixhawk 4 yourself — browser, route flight, motor failure (free, no hardware)
A while ago I posted about running the official PX4 firmware on an emulated Pixhawk 4 (STM32F765) coupled with a physics-simulated drone. Back then it wasn't released. It is now — and it's packaged so you can try it on your own PC.
Video (5 min, English captions): https://www.youtube.com/watch?v=XWAsmVYS8bM
What you can do
- Run the official PX4 v1.17.0 firmware, unmodified, on the emulated board. PX4's own drivers read emulated IMU, baro, mag and GPS chips.
- Fly the x500 from the browser (Athrill Studio): take off, hold, land.
- Click a route on the map, plan "stop motor 3 at point 2" (or click Stop during the flight). The motor stops inside the emulated DShot ESC, and PX4 detects it from its own ESC telemetry ("Motor failure detected").
How to run it
One repository sets everything up from an empty folder: no sudo, nothing installed outside that folder, every part pinned and SHA-256 checked. It runs on an Apple silicon Mac or Windows 11 with WSL2. No hardware, no GPU, free.
Not yet
- No hardware-accuracy claim: it's a light emulator, faithful at the RTOS/driver level, not cycle-accurate.
- One board (Pixhawk 4) and one firmware set (PX4) for now.
- Faults other than a stopped motor.
Code
- Athrill Studio (start here — "Try it on your PC"): https://github.com/hakoniwalab/athrill-studio
- Hakoniwa Business Pack (the one-folder setup): https://github.com/hakoniwalab/hakoniwa-business-pack
Feedback welcome — especially which faults or boards you'd want next.
r/diydrones • u/pokemonguy0417 • 1d ago
Other Executed this old sky hunter drone today using my airsoft guns
r/diydrones • u/LRFPV • 2d ago
Build Showcase First 106km Range Test of LoRa Video
The LoRa video system hit 106km during a range test.
- 2 dipoles (XRC Tri-antenna)
- 1W
- 915MHz
- Line of sight was partially obscured by earth curvature and lack of elevation on receiving end, hence the low LQ (Higher elevation would result in much better results)
Join the Discord for more info: https://discord.gg/xarVyFAzh
LEGAL DISCLAIMER – AMATEUR RADIO TESTING
This video depicts amateur radio testing and/or experimentation conducted in good faith and with the intention of adhering to all applicable amateur radio regulations, including FCC regulations under 47 CFR Part 97, where applicable.
All testing was intended to follow established amateur radio operating procedures, applicable frequency allocations, transmission requirements, and relevant legal guidelines. No intentional unlawful interference, unauthorized transmission, or violation of applicable communications regulations was intended.
All radio operators remain responsible for ensuring that their equipment, transmissions, and operating activities comply with applicable laws and regulations.
r/diydrones • u/pokemonguy0417 • 2d ago
Question Need help working on this drone do you know what is wrong with this drone?
This drone is a skyhunter drone (a cheap knock off DJI mini clone) trying to fix this drone for the purposes of selling it on facebook marketplace
r/diydrones • u/DogNo6170 • 2d ago
Wooden fpv is true.
reddit.comCan Finnish birch technology challenge carbon fibre in drone structures?
A new Finnish material innovation is attracting attention.
Skyboard Ultra is an advanced structural material made from ultra-thin birch veneers, developed as a potential alternative to conventional carbon fibre drone frames.
The technology combines lightweight construction, high stiffness and bio-based material content.
Developed in collaboration with Kolibri Defence, Skyboard Ultra represents an exciting opportunity for European material innovation and more resilient supply chains.
The story has now been featured in Finland's Tekniikka&Talous.
Read the article:
https://www.tekniikkatalous.fi/uutiset/a/3e4c48e8-8016-44fe-a180-1d3f5400fa5b
Finnish engineering. New material possibilities? Maybe? any other options?
r/diydrones • u/Own_Plate_7033 • 3d ago
Tired of guessing PID values? I made a free tool that reads your ArduPilot logs and suggests a tune, tested in sim before you fly
After a crash on my small quad (the log showed it before I understood it: vibration went through the roof), I spent a few weeks building a tool so I'd stop tuning by trial and error.
What it does, in plain terms:
You give it your ArduPilot `.BIN` flight logs
It checks the logs for problems: vibration, clipping, power, EKF
It learns how your specific drone responds from the flight data
It calculates new PID gains that should be stable, with safety margins
It test-flies the old and new tune in a simulator running the real ArduCopter firmware
It gives you a `.param` file to load in Mission Planner
The image is the crash in the log: you can see the vibration spike before it goes down.
It's free and open source, but it needs MATLAB:
https://github.com/Prateek-elec/ardupilot-flight-test-lab
Bench-test with props off and sanity-check any params before flying. Feedback is very welcome, especially from people with bigger or odd frames.
r/diydrones • u/Liangjun • 3d ago
AprilTag for PX4 Precision Landing
Have anyone tried using AprilTag for PX4 (Pixhawk 6c) for precision landing. I am getting into the point that my onboard PI 3 camera + Raspberry PI5 are able to detect the AprilTag with height distance and forward, left / right position, but I have not brought this Holybro S500 drone to the field to test it out.