r/Ubiquiti • • 18m ago

Question Ubiquiti nvr cameras for office business space

1 Upvotes

I am eyeing to put ubiquiti cameras and their G2 Pro NVR in our new office space. Its a 100K sqft stand alone building and we will need a 15-20 of those in total to cover the space.

We do our own IT and are getting Zyxel for networking hardware throughout w POE and such.

I want to know why I cannot get the G2 pro anywhere (its been non stock since longest). Should I just go to enterprise grand which is double the cost and call it done ?

How is their GUI compared to Axis or any other systems out there. We are not commerical or govt facility. Just an equipment builder


r/Ubiquiti • • 23m ago

Question AP recommendations

1 Upvotes

We are looking to add access points as part of a renovation. The house will be approximately 5200 feet, with the two main floors being 2000 sq ft each and the attic and basement around 600-700. We currently have two cat6 locations on the first floor, in the rooms at either end (one is in wall, and the other is actually inside a cabinet). The questions are: 1) what access points should we get for these locations? 2) we are planning to have one in the ceiling of the middle of the second floor- which AP would be best for that? And 3) can we get away with not having one in the basement or attic or should we add a fourth somewhere.

Thanks for your help!!


r/Ubiquiti • • 49m ago

Quality Shitpost Making up a project

Post image
1 Upvotes

I cut down a bunch of unruly non-native pine trees that were blocking my view of these beautiful mountains. The nerd in me now wants to figure out a line of sight networking project to take advantage of this. Those mountains are publicly accessible via walking trails. I obviously don’t have rights to install any equipment, so would have to be something low-powered and compact/covert. Anyone have any good ideas? It’s about a 5-6 mile shot across.


r/Ubiquiti • • 1h ago

Question U6+ White LED of Death

1 Upvotes

I have 2 running in standalone. Any help is appreciated.

I'm pretty sure its bricked. I power cycled my PoE switch and 1 of my APs came back up with it's known IP address but named as U6 Plus.

I took it down and got it plugged in straight into my PoE switch and factory reset it. I ran into a few weird things.

If I hold down the reset button for 20+ seconds, it will come back up with white and blue light flashing slowly. I let it run for 30 minutes and the lights still blink. Disconnecting it and reconnecting it to PoE brings it back up to a solid white LED.

If I hold it down for 15 seconds, it comes back up, same IP address, same name.

When I select the AP, I go straight into the AP connected confirmation screen, then the UniFi cloud gateway not detected, so I select set up without UniFi, and the 5 minute update will finish, and loop back to the start. The whole time, the AP is still solid white.

I can scan the QR code on the back to add it manually, and it will connect me to a SSID of the MAC address. It will then try to connect to the AP, and the circle doesn't finish/close out.

Out of RMA window since its about 3 years old. Firmware version: 6.6.55.15189


r/Ubiquiti • • 1h ago

Question UXG-pro owners: How is the smart outlet sensitivity?

1 Upvotes

Hello, I am planning to install a UXG-pro on a somewhat remote location where the modem requires a restart about once a month on average. I was reading that the UXG-pro is a little trigger happy when it comes to reset the modem, but most posts mentioning that have 2+ years. I would like to know if that issue was resolved on some of the newer firmware versions or if it still an issue.


r/Ubiquiti • • 2h ago

Question Ubiquiti 1G RJ45 SFP Module Not Working on Cloud Gateway Fiber – DAC Works Fine

0 Upvotes

I have a Ubiquiti 1G RJ45 SFP module that doesn't seem to work when plugged into the SFP port of my Cloud Gateway Fiber.

Here is what I've tested:

  • When I insert the 1G RJ45 SFP module, it doesn't establish a link.

  • I've also tried it in the second SFP port, with exactly the same result.

  • However, when I connect a DAC cable between the SFP port and a switch, it works perfectly fine.

So, the SFP ports themselves seem to be working correctly.

I'm wondering:

  1. Is there something I might be doing wrong, or is there any specific configuration required for a 1G RJ45 SFP module?

  2. Is it possible that the module is faulty, even though it's practically brand new (previously used very little)?

  3. Are there any compatibility issues with 1G RJ45 SFP modules on the Cloud Gateway Fiber?

  4. Is there anything else I should check before assuming the module is defective?

I'd appreciate any suggestions or similar experiences. Thanks!


r/Ubiquiti • • 3h ago

User Guide Adding a local CA?

Thumbnail reddit.com
1 Upvotes

r/Ubiquiti • • 4h ago

Question What APs have two ports - uplink and downlink?

0 Upvotes

Some of my older UniFi APs and have two ethernet ports I've got an inwall cable that has a break someplace. It terminates to a box in one of my rooms and I want to keep that box useful and have a hardline back to the network cabinet. I don't really want to rip up the wall and pull a new one. I'm hoping I can tone it and find the break and install a j-box around the break and stick an AP on the outside. Should I use an AP with two ports? Or put a bigger box and stick in a PoE powered switch and just a regular AP?


r/Ubiquiti • • 4h ago

Installation Picture Why doesn’t the WiFi work here?

Post image
424 Upvotes

Spotted in the wild….


r/Ubiquiti • • 4h ago

Installation Picture Spotted in the wild at our library

Post image
0 Upvotes

I always knew I liked this place ...


r/Ubiquiti • • 5h ago

Question Lumos Pro exploit attempt blocked by firewall

Thumbnail reddit.com
0 Upvotes

Any thoughts or similar experience ? Detected by UDMP


r/Ubiquiti • • 5h ago

Question Stepping into Unifi possibly, looking for advice

0 Upvotes

Evening all

currently I have 2 TPLink BE3600 devices, one connected to the modem downstairs, then this runs through a cat8 cable upstairs to the one in the office which has a switch connected for all my wired devices. so they are both wired. this works really well and the family are happy.

However we have multiple IOT devices, and a NAS running Jellyfin and the setup is becoming a but of a mess so i want to set up proper Vlans with appropriate firewall settings. Things the BE3600 cant support. So i am looking at Unifi

I was thinking of 2x UX7 with a small switch, basically mirroring what i have now, one by the modem with the WAN connected, then the Lan connecting to the one upstairs so both are wired.

I like the look of the UDR 7 and was thinking of using the Cat8 to connect the modem to a UDR7 upstairs so i wouldnt need a switch but then would need to connect to the UX7 downstairs via wifi / mesh as POE is not an option

am i better to stick to the 2xUX7? so they both broadcast wifi form a wired connection over 1 floor each?


r/Ubiquiti • • 5h ago

Question Network Setup Advice

Post image
0 Upvotes

I'm looking for some assistance, and I'm not sure if this is in the correct group. I'm not an expert by any means - I have an electrical engineering background, not any network engineering.

I've setup a network a couple of years ago for my in-law's bed and breakfast, and the normal day-to-day setup seems to be adequate (though, admittedly I should probably setup more VLAN's for extra security and I need to read up on how to properly set that up). Normal traffic usually includes about 10-30 clients, maybe just over 100 for a busy wedding. I can achieve almost 1G network speeds on the WiFi when the traffic is pretty low.

Once a year, we host a rather large fair with about 4000+ people on site. I obviously cannot support this type of traffic, so I just open it up to our vendors - maybe about 200 people who we've authorized to use it via a hidden SSID network. Every year it seems that even this traffic is enough to overwhelm my setup, so I've slowly modified the network topology to what you see here. Most of the traffic is confined to the two U6 Enterprise APs as well as the UWB XG AP - the rest of the APs are inside (the UAP Outdoor+ will be replaced with a new U6 or U7 Enterprise, but is in a location where not may people are located - just over an area where vendors camp overnight so it doesn't see any of the busy peak traffic). The outdoor coverage is rather large so I've got one of the APs separated by a fiber run located on the other end of the field which has helped with coverage.

This past year, I got a warning that the number of IP addresses was exceeded. So I discovered that I needed to decrease the DHCP lease time and modified the subnet with /23 to boost the number of clients. I've also thought about using the /22 subnet mask as well. Regardless, the WiFi network was still operating at a crawl and interesting enough the SSID would also disappear across all APs, though a separate hidden one I had set up for other devices would still broadcast.

I'm sure I'm doing something wrong and possibly have ineffective hardware somewhere. Is there a resource that anyone can point me towards to help? Sadly, it seems that I can only really test this setup once a year in a real-time environment.

I tried consulting with a couple of different network engineers and one suggested that I move everything to 2.4GHz radio only to get better coverage and disable the 5GHz, but that seemed to make the problem worse. Another wanted me to trash can it all and move to Aruba equipment so he could remotely configure it all as he set up several car dealerships and other small businesses and other high-end clients. Turns out, the owner was arrested shortly after for remotely accessing networks and security cameras (maybe some installed in personal spaces?) and was forced to dispose of his business which was sold to a different security company. I'm not sure if he avoided jail time or not.

So, any assistance, resources, or recommendations would be GREATLY appreciated!! Thanks.


r/Ubiquiti • • 5h ago

Question Any Fresh Rumors on a New Wifi Doorbell Product?

0 Upvotes

I searched but didn't see anything new ...

With Nest app being retired, I am going to have to change eventually. I have Unifi for other camera, etc. I just can't get POE to my doorbell.

Any Fresh Rumors or do I need to bite the bullet and install a Reolink?


r/Ubiquiti • • 6h ago

Question What to do with old security gateways

7 Upvotes

I've found that as the old 3P and PRO-4 security gateways are getting close to EoL that I am accumulating quite a few as I upgrade them to the new cloud gateways. It seems a shame to just throw them away but I don't know what else to do with them. I've looked on eBay and they're not even selling for £20.

So I'm here for your creative ideas of how to give them a longer useful life.


r/Ubiquiti • • 6h ago

Question Protect cameras are all blown out/overexposed

3 Upvotes

All of a sudden, all of my Protect cameras are super over-exposed and blown out, like the dynamic range just compressed dramatically. Changing the "exposure" and other settings in Protect doesn't seem to affect it much.

Did this change in a recent update?

This is how a black asphalt road looks from my G5 Ultra Turret before:

https://imgur.com/Xbuer1K.jpg

And today:

https://imgur.com/isbL90K.jpg


r/Ubiquiti • • 6h ago

Thank You Crazy difference between the UX and UX7 also size, my goodness what a better product though

Post image
86 Upvotes

r/Ubiquiti • • 6h ago

Question Apartment Wi-Fi - which solution should I choose?

3 Upvotes

Hi,

I have an apartment that isn't very big, around 70 m². I need to cover the apartment with Wi-Fi and I'm considering two scenarios, though I'm not sure which one would be better in terms of signal coverage:

  1. Dream Router 7 - the router would be placed roughly in the center of the apartment at about eye level

  2. Cloud Gateway Fiber + U7 Pro Max (or U7 Pro XG) - the AP would be ceiling-mounted in the center of the apartment, as usual

Which of these solutions is better, and what are your thoughts on them?

Thank you


r/Ubiquiti • • 7h ago

Question Using a PoE switch as an injector

0 Upvotes

Can someone double check my plan please. I have a fibre-terminating ONT that is powered by an external PSU and currently runs directly to WAN1 on my gateway. I'd like to power it with a PoE splitter because fewer plugs are better.

I have a splitter with the right output ports, but the gateway is a UCG-Ultra that doesn't do PoE. However I do have a USW-Lite-8 above it, so I'm thinking if I run a patch cable from the UCG's WAN1 to the USW and then from the USW to the splitter, I can get power. Then those two ports on the USW can be assigned a new native VLAN and the WAN traffic will route through the switch without touching my normal network, and then to the router. Does this sound right, and if so, is it sensible?

What I'd really like is a PoE injector that takes two cat5 inputs: one data and one power. Not sure if those exist though!


r/Ubiquiti • • 7h ago

Question Newly upgraded fiber speeds. Where is the wifi bottleneck in my system?

Post image
0 Upvotes

r/Ubiquiti • • 7h ago

Question UniFi Dream Router 7 or Express 7?

4 Upvotes

Hi,
I'm trying to decide between the Dream Router 7 and the Express 7.
I am running about 20 units on wifi and 10 wired. Functionality-wise they are close enough for me, what I am wondering about is overall quality.
I've read both good and bad about both on here, but the threads were a bit old, so any current input would be appreciated.


r/Ubiquiti • • 8h ago

Question UNVR-G2

1 Upvotes

I am looking to deploy unifi protect products at my house. Trying to understand the difference UNVR vs UNVR-g2 ? I understand that UNVR-g2 has AI, I thought the cameras have AI? what is the feature/value for a product which is 2x as much?


r/Ubiquiti • • 9h ago

Question Unifi Talk

26 Upvotes

I'm the IT guy for a fire department in the rural Midwest. Our networking for the station runs on a dream machine and a switch, and I'm trying to port our cameras over. The department is wanting to switch to a phone system that is not with (local provider), as we've had no end of issues with it, (lots of spam calls, poor service, etc)

They would like to have a VoIP system. Or something more digital. Is Unifi Talk an easy enough alternative for a retrofit to an existing on prem system?


r/Ubiquiti • • 9h ago

Question Wired clients “ghost” dropping

1 Upvotes

UniFi logs show thousands of wired client disconnects/reconnects. Devices immediately reconnect, and continuous ping commands verify that devices are not actually going offline. Network feels slow. Anyone seen this before?