r/Plumbing • • 1d ago

Can anybody explain what went wrong?

Post image
174 Upvotes

this is a 750L water storage tank placed on the roof top. The tank was overflowing as it got full but even after turning the pump off, the water kept overflowing for more time than it usually does.

Today I discovered that the tank has become like this and this. What should be done?


r/Plumbing • • 3h ago

Replacing Toilet Seat - Hatria

Thumbnail
gallery
3 Upvotes

Good morning, everyone. I have a toilet at home with a broken seat. I can’t seem to find the exact model; the only information I have is the brand name, Hatria, and the number 37/07 on the seat.

I live in Switzerland; we bought the house, and unfortunately, I don’t have any more information.

Seat width: 34.5 cm, length: 41.5 cm, screw spacing: 16 cm.

Thanks in advance!


r/Plumbing • • 15m ago

Left side is always slow to drain

Post image
1 Upvotes

What can I do to improve the drain on the left side? It always drains slow.

Thanks for any suggestions.


r/Plumbing • • 9h ago

Can a disconnected gas water heater flue melt an ABS shower P-trap overhead?

Thumbnail
gallery
4 Upvotes

Has anyone ever seen this happen? A brand-new black ABS shower P-trap sat completely fine in my open garage ceiling bay for 4 weeks (it was replaced due to the contractors who did my shower remodel allowed grout to fill the P-trap), then suddenly buckled inward and turned gummy/squishy two days after a drywall crew disconnected my gas water heater flue for most of the day while the tank was still running.

Nobody poured any chemicals down the drain. My contractor says he’s never seen this in 30 years and thinks the drywall/wood would have scorched too. Three different plumbers looked at this, and neither of them said that they’ve ever seen anything like this, with one of them saying that the tank only heats water to ~180°F: but isn't atmospheric flue exhaust 300°F–400°F+ while ABS softens around 200+°F?

Am I crazy, or did the open flue cook the ABS trap in that open ceiling bay? You would think this type of damage would take a little bit more time than just one day.


r/Plumbing • • 8h ago

Water Meter / Leak Help

Thumbnail
gallery
3 Upvotes

Hello all, I just wanted to get some feedback
On my water meter and a potential leak.

I recently had a plumber come out on two seperate days and replace a few valves for me (and an hvac to make a furnace repair). I noticed the second time the plumber came out when he left that on my water meter the center silver gauge was moving back and forth. Barely even noticeable but if I sat and watched it for 20 minutes eventually I’d catch it wiggling back and forth.

Since then, it has noticeably moved less and less and now I can leave it unwatched for 5 hours or more and it barely moves. Pic #1 is from 6pm when I left the house and #2 is from 11:30pm when I got home. The center silver gauge barely moved but it still did something.

Any one have any idea if it’s for sure a leak or may be something else? I’ve ran a toilet dye test on my toilets and after a 4 hour window no color leaked through. I’m a bit nervous to try turning off valves to determine if it’s something else due to many of them being old and not wanting to break them and pay out more for a plumber to come out again…

Thanks in advance for any advice.


r/Plumbing • • 3h ago

Whale shower pump has always only worked intermittently in a wet floor setting

1 Upvotes

We had a wet floor and pump installed for my disabled mum however since install it stops working regularly as in the Pump works but doesn't take water away.

Opened and re-tightened inlet and outlet piping and previously this worked for a while for a little time each time

Now when I take outlet side of pump piping off and place my thumb over I can feel the suction, however takes a few pumps before water follows, when I remove thumb, water stops but lump keeps going

I have used a wet hoover to suck water from the inlet side, there wasn't much debris

Am I left with investigating a possible air gap in the piping leading to the pump under the floor?

At end of tether with this.


r/Plumbing • • 14h ago

I’ve seen these ads and wanted to add a psa.

Post image
7 Upvotes

If you plan on remodeling a bathroom, budget extra to open the walls and change the pipes. Better to do it now before the pipes destroy a brand new bathroom or you have to tear out a brand new vanity to fix the sink drain that’s stopped up.


r/Plumbing • • 15h ago

Bathroom sink keep dripping from the handle.

Post image
7 Upvotes

Hey guys. Trying fix a few things around the house.
I’m currently stuck on fixing the bathroom sink from leaking water from under the handle area. I removed the handle. But I can’t get this part off. It is covered in calcium and is basically welded on. I already put lime away and vinegar in it.

Anyone has any recommendations on how to remove this item


r/Plumbing • • 14h ago

Is that enough height difference?

Thumbnail
gallery
4 Upvotes

About 2 inches height difference between disposal exit and wall drain


r/Plumbing • • 11h ago

HELP. Dripping/Thumping noise in my walls whenever my neighbour uses water.

2 Upvotes

Can someone please explain what this is and why it is happening? It happens whenever my neighbour or I use water.

For context, we share a water meter if that helps and I have been living her for 3 months, and it’s been doing it every day, but never happened during any of the inspections.


r/Plumbing • • 15h ago

Tub Surround

Thumbnail
gallery
4 Upvotes

I had a plumber come install the bathtub while I was going to do the surround. As im installing the surround, the back wall surround fits in no problem. However, the side wall snaps in, but as I go to push it against the wall, it is completely unleveled. And the top and bottom are off. The tub is not level.
I know it may be shotty, but would it hurt to silicone/caulk where the gaps are at the bottom?


r/Plumbing • • 8h ago

Roman Tub Stem Brand/Model?

Thumbnail
gallery
0 Upvotes

Anyone know what brand and model this stem this is and where to get it?


r/Plumbing • • 12h ago

Is there anything I can do with this?

Thumbnail
gallery
2 Upvotes

My shower was leaking, so I turned it a little to see if it was not tight enough and it stripped something and now I’m having to have my water supply off. Plumbing place is closed for the weekend. Home Depot is open. Is there anything I can do to at least temporarily fix it?


r/Plumbing • • 12h ago

AAV and old washer hookup tips

Post image
2 Upvotes

Recently moved washer/dryer to basement and want to clean up these vents and hookups that I don’t need anymore. Eventually put a storage cabinet here. The hookups I plan to cap off and cover.

Any risk with hacking out the AAV and capping off? There is a shower on the opposite side of that wall and the AAV and washer drain line connect to it under the floor. Want to make sure that won’t affect shower drain before proceeding. Any other best practice tips?


r/Plumbing • • 9h ago

Wife wanted to paint the bathroom...

Thumbnail
gallery
0 Upvotes

So naturally, the vanity had to be replaced.

Hello Reddit Plumbers, long time listener, first time caller. Could use some advice on this, I'm facing a couple issues. With the existing trap I'm about 2 inches off.

One problem is the metal pipe in the wall is 1 1/4 inch, and I can't find a 45 degree for it, only 1 1/2. The woman at Menards said I should try the 1 1/2" with some down sizing washers, which I did, but then it leaked right by the wall. I couldn't tell if it was leaking from the 45, or from the stub going into the metal pipe, which leads to the next problem.

When I tighten down the metal nut on the pipe in the wall, it doesn't seem to grab the plastic pipe at all. You can spin it and pull it out. It has been like that for years, since we bought the place, I think the plastic pipe was just stuck far enough back into the metal pipe that it wasn't ever a problem. Now working on it, the plastic stub is shorter, and it might be the reason the water is leaking.

With the 45 degree in place, I had my wife pour water, and it drained fine when poured slowly. When she dumped a pitcher down it, it leaked horribly.

Hopefully people have some suggestions other than tearing open the wall, lol. Thanks


r/Plumbing • • 9h ago

Post ian plumbing roughin

Thumbnail
gallery
0 Upvotes

I dont even know where to begin. GC hired a plumber to do post Ian roughin. This is a beachfront home in Lee County Fla. Flood zone AE. Prior to this roughin, I had a few exposed pipes under the carport (yellow pipes). All white pipes are new. He could have run the majority of new pipes between the t1-11 and subfloor parallel to joists. Instead, he put all new pipes under the home These were validated as PVC (unpainted), exposed to elements, nailed directly to T1-11 (dont know if he hit any joists), no sealing of the exposed cut outs, brackets failing, improper spacing of brackets. The aesthetics itself are awful. Look at the plex pipes. No sleeves to prevent chafing and lots more. Im sorry, but im an elderly female who feels shes been taken to the cleaners and am trying to work out a solution with the GC...who's giving every excuse in the book. Of course, Im just a ignorant woman who knows nothing about plumbing (in his opinion). Hes already billed me for this roughin and is expecting payment in about 15 days. Hes the type that will put a lien on the property if not paid. Im just asking if this looks like shoddy, wham bam thank you ma'am type work....take it or Ill be charging extra to "fix it". I do know defects when I see them. I dont think this is acceptable work. But I have noone to back me up. By the way, all this work was passed by an independent inspector. They also ran pipes inside for a regular size water heater when plans called for a lowboy. And ran pipes for toilet way too close to walls. Would appreciate any input from people who know whats wrong here and how to "push back" to the GC.


r/Plumbing • • 1d ago

Leaking Well Pump

Post image
18 Upvotes

I have an old Beatty piston style well pump. Everything seems to operate on it as it should, other then it is leaking around the brass piston as it cycles. Can anyone recommend if/how to fix? See photo.


r/Plumbing • • 17h ago

Tankless water heater rec

4 Upvotes

My water heater just went out. I've been thinking about switching to a tankless. Any reason I should stay away from tankless other than c0st? Also any brand I should stay away from. I was just going to pick one from Home depot.


r/Plumbing • • 14h ago

Identifying material

Post image
2 Upvotes

I believe this is polybutylene. Its for a mobile home built in1979. My mom sent me this picture and shes old and wasn't able to find any markings on the pipe. So my question is whats the material of the pipe and is this just a push to thread fitting i can find or am I going to have to cut the pipe, and convert what I can to pex b to thread it in? She's an hour drive away so I would like to show up with everything I would need in hand.


r/Plumbing • • 16h ago

Is there something wrong with my toilet ?

Post image
3 Upvotes

I’ve noticed the base of my toilet is sort of shiny right where at the floor. I thought it might just need to be cleaned, but it still seems to look that way. Is this a sign of impending disaster?


r/Plumbing • • 10h ago

No Hot Water coming from my triple sink faucet but...

Thumbnail
gallery
1 Upvotes

I can feel the fixture being hot and there's hot water dripping from the handle; there's a trickle of cold water coming from the faucet regardless of the hot setting and the cold being off.

I checked the tightness of the hot handle with a screwdriver and it seems tightened properly. Underneath/behind the triple sink it kinda looks like the hot line (right line in the attached picture underneath the sink) is turned away/wrapped around the connector point for some weird reason? That's my best guess as to what is causing the issue.

Sorry for any missing info to provide, I'm completely ignorant of anything relating to this type of hardware and am just in a bind at work so I figured I'd reach out to the internet. Thank you in advance for your assistance


r/Plumbing • • 12h ago

John Wood Vs Rheem

1 Upvotes

I am proactively replacing my hot water tank as it’s 14 years old (in a townhouse). I currently have a John Wood 184 L electric tank and it’s worked and lasted well.

I could get a replacement John Wood E50TE-45208 with a 6 year warranty 1 year labour or a Rheem Performance Plus with a 9 year warranty 1 year labour.

I am leaning towards the John Wood as this current tank has lasted well but I can’t really find reviews. Does anyone have any experience with this tank and its performance?

Thanks


r/Plumbing • • 15h ago

Easy fix?

Thumbnail
gallery
2 Upvotes

Pipe is leaking where the blue line is on first pic. What is that large bulky thing near the middle, and is it easily removeable? I imagine if it just dismantles, I can just replace the parts.


r/Plumbing • • 12h ago

ID Shower Head

Thumbnail
gallery
1 Upvotes

I liked this shower head. Surprisingly so for a hotel. Found a the Canopy by Hilton in Memphis