r/Motors • u/PunkiesBoner • Jul 20 '25
r/Motors • u/downtownpartytime • Jul 14 '25
Am I doing something wrong or is Amazon sending me bad capacitors?
A/c condenser fan motor is doing a bad job of starting. I tested that capacitor and it was like 3uf. Ordered a new 7.5 from Amazon, tested it before installing and get 0, order another, different brand, and test it and same thing. Are they sending me garbage or am I doing something wrong?
r/Motors • u/BlacksmithWinter7823 • Aug 27 '25
Antique 40 hp motor pulled from 1930’s building
I removed this motor from the rafters of a 1930’s building. I would like to sell it to help cover costs. Unfortunately, I have no idea what something like this would be valued at. If anyone has any knowledge on these old motors, I would like to get a ballpark number on what it maybe worth and how much it may weigh.
r/Motors • u/Popa_Filly • Apr 27 '26
Antique Blador Motor
Wrapped on my antique Baldor Motor today!! 💪
Recap: this motor came in a 1945 Delta Milwaukee bandsaw I picked up a couple months ago. A member here, ID’d it to be an antique Blador motor. While I still wasn’t able to find a similar example online, I searched Google books for digitized publications (filtered for 1920-1930) for “Baldor Motor” and was able to find a few adds with illustrations of this motor as well as examples of the motor tag. With that I’ve narrowed the age of the motor to be as early as 1926, based on the date of the publications where I found the matching illustrations.
The motor is neat, 6-pole/1200 RPM (1140 under load) the lower RPM makes sense as this was on a saw set up to cut metal. Based on my amperage testing, I settled on 1HP. It’s a heavy duty motor at 65lbs and has a 3/4” shaft.
I pulled it completely open, and cleaned out the likely 100 years of shop dust caked in the motor. Degreased the bearings which were in phenomenal shape and spin so nicely after the cleaning. I cleaned everything inside, and polished all the bare metal parts. Repainted the castings, but left the laminated steel bare, then clear coated. New lubricants and closed it all up, and it runs like a top.
The badge I recreated on my computer based on the add illustrations and sent out to have done professionally from Von Industrial. I had him leave the specs blank and I hand stamped them in.
Not sure exactly what I plan to do with the motor just yet. It might go back to work in a machine, or it might be a piece of art in the shop. 🙌
r/Motors • u/PanicPineapple0 • Jul 08 '20
General Lego Motor Lifts 200lb Rock through Gear Reduction
r/Motors • u/Bigbore_729 • Dec 09 '21
General 7.5hp P&H. Coils made, material cut, and coils completely inserted all by me in 8 hours.
r/Motors • u/VarsitySquad • Nov 29 '19
General Was sent here from r/electronics. I rewind motors for a living.
r/Motors • u/Ill-Painter208 • Feb 08 '25
Just finished this project
I'm a motor winder ac and dc... ask away.
r/Motors • u/Bigbore_729 • Apr 02 '21
General 700 HP dual speed 2300v form winding with 2 windings in one explosion proof stator
r/Motors • u/Bigbore_729 • Sep 16 '20
Open question Any other winders here insulate their coils like this?
r/Motors • u/StormingMoose • May 17 '26
Old Motor. Any ideas?
Does this look familiar to anyone?
r/Motors • u/ErasylD • May 29 '26
General BLCD motor on 3d printer
My own bldc motor fully designed by me and printed on 3d printer, no rpm test yet, but some successful launches has been done. Next steps to add back iron, VESC, more voltage and other stuff with some better design. Some extraordinary ideas about next design would be appreciated!
r/Motors • u/Bigbore_729 • Sep 16 '20
General 400 HP 4160v. Coils made in 3 days, coils inserted in 2.5 hours
r/Motors • u/1Davide • Apr 09 '20
General Machine-winding of the rotor for an electric motor
r/Motors • u/TheMacgyver2 • Jan 31 '26
General Milling machine motor completed
Hey guys, it's been a year since I got a bunch of advice on my first motor rewind. This project really took me into the weeds.
I attempted to rewind in the same oddball pattern of the original motor. Despite having the original coils to measure, my coils were slightly too small and the last coil group was impossible to install. I put it on the back burner out of frustration for almost a year.
I bought an old motor rewinding manual off ebay and after making my brain burn for a month or so came up with a plan to change the winding to a new pattern. I mostly based this off a diagram I found online that seemed to agree with my book.
I very carefully unwound my previously wound coils and rewound them into new coil groups in order to not have to purchase two new rolls of wire. I'm not sure how good of an idea that was but it seems I got away with it.
After winding and tieing my motor. I hooked it up to a vfd, and blew up the vfd. Thinking I had screwed something up I untied and checked all my connections. They all matched the schematic....so I drew up a new schematic and realized the start and end of the yellow phases were reversed in the online schematic. After correcting the yellow phase the motor worked. I then used electrical spray varnish to soak the coils as much as possible and got the motor nice and warm to cure the varnish.
So this post is a thankyou to everyone who gave me advice initially, I'm calling it a success, albeit not an easy one.
r/Motors • u/ArnauAguilar • Dec 19 '24
Open question Made my first ever bldc motor, struggling to evaluate it's performance, help!
Hi, first of all i'm not an engineer (but I wish I was!) I'm learning on my own at my shop.
I've designed and built my own bldc motor and I want to test it's performance and get some metrics (Kv, Ke, back emf...) sp that i can build a better one next time
I've built a small test rig where I have a known comercial bldc motor controlled by a FOC controller coupled to my MUT(motor under test) motor.
My first issue is that if I measure the rpm at a certain voltage and calculate the KV I get around 21, but if I measure the back emf from the MUT and calculate the KV front that I get around 28. I'm not sure if that's too much discrepancy, and if it is where can it be coming from? I've re-tesyed everything several times... Any help, suggestion or direction would be appreciated!
Here is a short video of the motor running: https://youtube.com/shorts/igbXB_XZKwk?si=aqdPnJlUTCPhqemh
And I've attached fotos of the test rig as well as a spreadsheet with all the data I've been able to measure
r/Motors • u/ArnauAguilar • Apr 17 '26
Open question 3D printed monster motor that lifts + 15kg!
I finally have ready the first working version of a BLDC motor i'm working on. It's a torque monster and also quite a good generator!
There are a lot of modifications i have to do still, but I'll release the files once done!
How should I test it? What could it be used for?
My biggest issue now is finding an ESC controller that works great with this motor, everything i tried need help (pushing it by hand) when starting up. In the video i'musing a FOC odrive
Find a video here: https://www.reddit.com/u/ArnauAguilar/s/I13UItUxyn
Here are the specs:
KV: 4.1 RPM/V
Kt: 2 Nm/A
Phase resistance: 1.5 Ω
Peak torque: 13.3Nm
Base speed @ 24V: 60 RPM
Stator specs:
OD: 138mm
Depth: 60mm
Slots: 36
Wire OD: 0.8mm
Turns per slot: 25
Rotor specs:
OD: 180mm
Poles: 40
Magnet: N-42 Neodiymium
Air gap: 1mm
r/Motors • u/Organic_Cold_6491 • Mar 20 '23
Open question Tesla Motor repair
So a friend in Madeira Island in Portugal has a company that specializes in repairing and rewinding electric motors and transformers, from the small ones up to substations and anything giant. So a costumer asked him if he could repair a Tesla motor! He said yes, and even though he had to built some tools for the job, here are the results. Not sure if this is not the first Tesla motor to be repaired. Tell me what you think. Car is running perfectly since this was done some months ago.