r/Motors • • 2h ago

General Where can I get a rewinding done for this 1950s refrigerator compressor

Thumbnail
gallery
2 Upvotes

r/Motors • • 3h ago

Open question [Design review] Relay stop line and isolated DAC throttle for a 48 V motor controller

Thumbnail
gallery
1 Upvotes
Two small circuits for a 48 V golf cart controller (Curtis 1268). Schematics attached.

1. Stop line
- Key feed, then the stock pedal switch with relay K10 in parallel. Then relay K13, then two NC e-stops, then the controller input (J1-8).
- Both relays are Finder 40.61 with 12 V coils, driven by NPN transistors (2N2222, 1k base resistors, 1N4007 flyback diodes) from an Arduino Nano.
- PC817 optos (22k 1/2 W series resistor, 1N4148 reverse diode) watch the key feed, the pedal node and the line after the e-stops, so the Nano can detect a welded contact.

2. Throttle
- An MCP4725 DAC on an isolated 5 V supply, I2C through an ISO1540, referenced to the controller's B-.
- Output goes through a 10-turn trimmer to the NO side of a DPDT relay. NC is the stock pedal pot wiper. Common goes to the controller throttle input (J1-15), with a 10k pull-down to the pot low end.
- Range is held at 0.5 to 4.5 V because the controller faults at 4.7 V.

Questions
1. Are the opto resistor values right for a 48 to 65 V DC line? (About 3 mA, 0.19 W in the 22k at 64.8 V full charge.)
2. Any issue with 2N2222s driving these coils?
3. Is the isolation on the DAC side sound, and is the 10k pull-down sensible?
4. Anything you'd change?

Thanks

r/Motors • • 1d ago

Hi guys , is this wired correctly ?

Thumbnail
gallery
0 Upvotes

I wired this electric motor up but it’s giving me lots of problems , it’s overworking to run and it over heats even with no load attached in about 5 minutes


r/Motors • • 1d ago

Open question Why new bench grinder heats up very quickly?

Post image
1 Upvotes

Is it normal to work heat up like this


r/Motors • • 1d ago

Open question Vacuum Motor Replacement for a Carpet Extractor.

Thumbnail
gallery
0 Upvotes

Hello everyone! I'm trying to replace this vacuum motor in a carpet extractor. On the old motor, the internals got shredded from sucking something up through the vent. The OEM motor is like $500 so I was wondering if I can just get a three stage vacuum motor on Amazon that's nearly exactly the same. Anything I should be aware of before making the purchase? Thanks!


r/Motors • • 2d ago

Open question 4-in-1 ESC: outer motor pad dead on both motors on one side?

1 Upvotes

SEQURE Blueson A2 4-in-1 (AM32), RS2205 motors. The two motors on one side twitch and only work intermittently; the other side runs fine.
On both bad motors, pads 2–3 on continuity test beep, but pad 1 doesn’t. And its symmetric so (1-2-3) (3-2-1) being the three phases of the two motors, port 1 of both dont seem to be connected.
On the good side all pads beep on the continuity test with each other.
My soldering is good no worries on that im sure. I cant seem to find a solution to this, if someone is familiar with this i would really appreciate it if you could help me out.


r/Motors • • 3d ago

Open question Cheap and reliable way to continuously monitor load on a stepper motor?

1 Upvotes

I'm looking for an inexpensive and reliable way to continuously monitor the mechanical load on a NEMA 17 stepper motor connected to a 5.18:1 reduction gearbox.

The motor operates at relatively low speeds and frequently changes direction. I don't need highly accurate torque measurements in N·m, just a consistent indication of how much load the motor is experiencing so I can detect increases in resistance before it stalls.

I'm currently using a TMC2209 driver with an ESP32.

I've considered a few options:

- StallGuard4: Seems promising, but from what I've read, it's unreliable at low speeds.

- Current sensing: I've previously used current sensors with servos to detect increased mechanical load, but I understand that stepper drivers regulate winding current, making this more difficult.

- Rotary torque sensors: Would be ideal, but commercial options seem far too expensive.

- Flexible shaft coupler: Possibly measuring torsional deflection to estimate torque, although I'm unsure how practical or accurate this would be.

- Load cell: Measuring reaction torque could work, but I'd prefer something compact that doesn't require significantly modifying the motor mounting arrangement.

I'm trying to keep the cost as low as possible, ideally under $20–30 CAD.

Has anyone implemented a cheap method for continuously estimating stepper motor load at low RPM, particularly with frequent direction changes?

I'm open to DIY solutions, additional sensors, or clever ways of using the existing driver. I don't need precision, just reliable and repeatable relative load measurements.


r/Motors • • 5d ago

Electric motors keep giving up , have no idea why

Thumbnail
gallery
12 Upvotes

Hi everyone , I’ve been having problems getting my electric motor to power this wheel smoothly and I’m at my last straw as nothing is working, any input is much appreciated,

this is a pewter wheel for polishing stones on , underneath the bench there is a pulley system powered by a 3 phase electric motor , there’s a belt connected to the pulley which is tightened to the bottom half of the spindle which spins the wheel, The tips on both ends of the spindle sit on a block of rose wood which allow the wheel to spin freely.

I previously used single fase motors and they would work so hard to get the wheel up to speed they’d just over heat and give up due to too much tension on the motor , so I had just assumed a more powerful 3 phase motor would fix the issue but it still cannot handle the load it gets so hot to the point it just melts the insides.

What I don’t understand is that the guy who designed this setup has multiple benches with the exact same pulley system with single phase motors powering the exact same wheels and for many years he has faced no issues with overloading or tension on the motor, so I’ve gone and built the setup identical to his and the motors dont like it. It just doesn’t make any sense, i have tried tightening the belt and loosening it, have had multiple electricians check the wiring and the power and no issues there , I’ve secured the motor and straightened everything up about a hundred times but the motor just cannot seem to take the spin the wheel consistently without it overheating and blowing up . Something is clearly incorrect and I just cannot understand what is I feel like I’ve tried every possible thing .

I am in Ireland and the guy who designed this setup is in UK and he can only tell me that he has multiple set ups exactly the same and there is no reason for it not to work 🤯🤯🤯


r/Motors • • 6d ago

Answered why is the motor sparking, can i do anything about it?

Post image
1 Upvotes

hi, im not native english, might not know certain terms.

i have this 1200W mortar mixer and lately i noticed that you can see some sparks in the back air intake, also with the spark you could hear a sparking sound (like little flash sounds). i know to some degree this is normal, only i was using it in a place with somewhat unstable electric (a place connected with a big diameter but very long extention cord), i had lights on the same circuit and you could see them dimming down / flickering exactly in the moments when i could see little flashes / light arks inside the motor.

first i assumed that maybe the carbon / coal contacts would be worn down, i pulled one out (pic), but it looks very new to me.

is there anything else i can do to make the motor do less sparks / have less amp draw fluctuation so i don't stress the power source and long cable?

(i am off grid on a farm, i have a 10kW inverter, but distances are long and that cannot be changed...)


r/Motors • • 7d ago

Open question Looking where to buy DC gear motors

2 Upvotes

I been looking for a website to buy DC brushed motors, or in just general a website that specializes in selling AC/DC motors that can deliver to USA, I tried with Amazon and eBay, but both of them have a really general variety, they usually just sell the typical hobby basic motor such as the 775, or just the typical 3V yellow gearbox motors, I have to say that I have tried with Stepper online and it’s probably the closest thing to what I am looking for, the big problem is that they for some reason don’t deliver Germany storage motors to the US, china storage ones delivery prices are exaggerated and typically cost 80-100$ for a small Motor or a small item, and their USA catalog storage is incredibly small.

eBay is a good option when looking for big/used/or cheap motors, especially AC of 3 phases or when they start to get categorized in HP

Thanks.


r/Motors • • 7d ago

Open question Wiring 12V Noctua PWM Fans to AC Infinity 10V UIS Port for Constant Climate

1 Upvotes

Hi everyone,
I am currently building a premium DIY indoor plant cabinet for my rare aroids (Monsteras, Alocasias, etc.). The goal is to automate the entire ecosystem through the AC Infinity Controller AI+.
For humidity spikes and temperature control, I am setting up a dual-fan intake at the bottom and a dual-fan exhaust at the top using Noctua NF-A14x25 G2 PWM fans. I also have the matching AC Infinity CLOUDFORGE humidifier connected natively to handle low humidity.
Here is the most critical part of my project: I need the Noctua fans to run on a true, linear scale from level 1 to 10 based on the controller's dynamic transition settings.
I absolutely do NOT want a simple ON/OFF solution where the fans just jump from 0 straight to 10 or toggle back and forth. Instead, they need to scale smoothly—cruising quietly at level 2 or 3 when the climate is near perfect, ramping up to 5 or 6 if things drift, and only hitting 10 during extreme spikes. This is the only way to keep the temperature and humidity completely stable and constant without crashing the environment.
Since AC Infinity UIS (USB-C) ports output a proprietary 10V PWM signal and Noctua G2 fans expect a 5V PWM signal (along with a separate 12V DC power source), I am comfortable soldering a custom adapter box.
Could you please help me with the exact electronics needed to achieve this true variable speed control?
How do I properly wire the 10V UIS PWM signal to the 5V Noctua PWM pin to ensure the fan's internal controller reads the full linear range (1–10) correctly?
Is a simple voltage divider using two 10 kΩ resistors enough to achieve this smooth scaling, or will it cause the fans to behave erratically?
What is the exact pinout/wire color mapping of the AC Infinity UIS cable for the 10V PWM out and GND?
How do I properly bridge the common ground (GND) between the external 12V power supply and the controller so the signal transmission remains perfectly clean?
If anyone has a proven wiring diagram, a forum thread link, or has successfully achieved this smooth, multi-speed scaling with this exact hardware, I would be incredibly grateful for your guidance!
Thanks a lot!


r/Motors • • 7d ago

Open question removing the screw behind a gear

Thumbnail
gallery
2 Upvotes

taking apart my shredder to try and clean it thoroughly as it was getting dangerously hot all the time. i’ve almost got all of it except this last plastic part; it’s held in place by a screw that is completely blocked by this gear and i cannot figure out how to remove the gear. there aren’t any threads in the holes and i can’t pry it off, nor am i able to move the gear independently of the shaft and whatever cap might be on it. hammering from the other side doesn’t work either

i know i could probably clean it without taking it fully apart but i am autistically determined to defeat this thing (it’s a cheap thing from walmart i’ve had for years so i wont be devastated if i completely break it but i want to take it apart dammit!) help!


r/Motors • • 7d ago

Open question How can excessive vibration in rotating machines be reduced?

1 Upvotes

I am a first-year Mechanical Engineering student. What are the common causes of excessive vibration in rotating machines such as motors, pumps, and fans, and what methods can be used to reduce it?


r/Motors • • 8d ago

Open question ZLTECH ZLAC8015 hub motor servo driver: looking for config software and correct Modbus RTU register map

1 Upvotes

Hi everyone!

Has anyone here worked with the ZLTECH ZLAC8015 servo driver for hub motors?

I’m using it in an AGV robotics project at my university, but the software that came with the driver was lost, and the manufacturer hasn’t replied to my emails yet.

My setup:

Driver: ZLTECH ZLAC8015 + ZLTECH hub motors with encoder

Controller: ESP32 + MAX485 module

Communication: RS485 Modbus-RTU, 115200 bps, slave ID 1

The problem: I can read holding registers in the 0x2000-0x207F range, but the register addresses I found online return “Illegal data address”, so I’m not sure whether they match my firmware version.

Does anyone have:

The correct Modbus-RTU register map for the ZLAC8015 (control word, operation mode, target speed, actual speed, fault code)?

The PC configuration software, or a link to it?

Example code (Arduino/ESP32/Python) that works with this driver?

Any hints, links, or GitHub repos would be a huge help. Thanks in advance!


r/Motors • • 9d ago

General Would a Voltmeter Notice Something Wrong with an Overheating Motor?

3 Upvotes

I've sometimes seen news articles of where traction motors have caught on fire. So I'm curious, if you hooked up a voltmeter to a motor, what would it look like when it is overheating? Let's say it's a 3-phase induction motor, although I think the answer is going to be the same for any traction motor.

What if you also had an independent measure of RPM? If I had to guess, I think an overheating motor would look like a voltage drop and declining RPM (all the energy going into heat instead of propulsion).

Say you were trying to design a system to log information for maintenance. On electrical locomotive, if each motor was measured by a voltmeter and you had to choose at least 2 places to measure voltage, where would they be? The inverter?


r/Motors • • 9d ago

Open question Persistent humidity around my water booster pump – is a dehumidifier a good idea?

Thumbnail
gallery
1 Upvotes

Hi everyone, I’m not entirely sure this is the right subreddit for this, so apologies in advance if it isn’t. Any pointers in the right direction would be much appreciated.
I have a water booster pump (motor with a pressure tank) installed in the basement of my building. There’s constant dampness in that area, so I bought a hygrometer to check. It reads 15.2 °C and 65% relative humidity, and that’s with a window open for ventilation, so this is basically the best-ventilated state I can get down there.
The motor has some light rust on it, and it occasionally runs noisy. I suspect the motor is “sweating” (condensation forming on it), which would explain the rust.
My idea is to put a dehumidifier down there and route its water drain into the nearby plumbing so it can run continuously.
My questions:
Does a dehumidifier sound like a reasonable solution here?
What humidity range should I aim for to keep the motor safe?
Is there anything simpler I should try first?
Photos attached. Thanks in advance for your time


r/Motors • • 10d ago

Open question Color wire in motor

2 Upvotes

Why is this wire colored red? You can see under it that the wire is bare copper. What is the difference?


r/Motors • • 10d ago

Open question Any recommendations for making with this rs 555 dc motor

1 Upvotes

It runs on 12v 2amps but i run it with a 12v 5amps adapter im saying about any useful things for home except a water pump


r/Motors • • 12d ago

Open question Would this connection work?

Post image
5 Upvotes

Hi,

I am rewinding my first motor for a personal project, and had a really difficult time mapping out the original connections. I know it is a 6 pole 3 phase motor, so is there a reason I can't move the order of some of the groups?

Having the terminal wires coming off in similar locations will make it much easier for me to figure out, but it would be a bit different from the original setup, where T1 T2 and T3 seemed to start at random groups in the motor. I could see maybe magnetic imbalance being a problem, but any info would be helpful. Thank you!


r/Motors • • 12d ago

Open question Controlling hysteresis brake

3 Upvotes

Is it possible to control a hysteresis brake using esp32 driven MOSFET. It’s a 24v, 800mA hysteresis brake and I’ll be using close loop system( with a load cell and encoder) for precise readings. If anyone knows anything about this topic please help.
Or if there are any other ways I am open to them as well.


r/Motors • • 12d ago

Open question Motor design software for BLDC motor

4 Upvotes

Good evening everyone,

I am a senior in EE and am in charge of designing an inrunner bldc motor for my capstone project. I have been using an online software called MotorDesignSoftware to build my motor but its applications are very limited for what I need. I was wondering if anyone had input on another software for motor design?


r/Motors • • 12d ago

24V brushed dc motor recommendations?

1 Upvotes

https://www.servocity.com/170-rpm-econ-gear-motor/

Like that but 24V. It is light weight as well (100 gram). I want 24V brushed dc motor (not brushless) that has high power to weight ratio. Any recommendations?


r/Motors • • 13d ago

Open question Help finding replacement

Thumbnail
gallery
2 Upvotes

Hi all, need help finding a replacement for this circa 1954 Universal Electric Co motor. Its a 4-7/8 case with a 5/16 d shaft. 230v 1/30 HP 1550 rpm. Mounts to frame on a modine style heater with 4 threaded holes on the case. Hope someone can help.


r/Motors • • 13d ago

Open question FOC related

1 Upvotes

Hello guys,

I have few doubts,

What if the back emf is equal to the applied voltage of motor, will the current consumption of motor will become zero because there is no potential difference right in this case?

And how this Id,Iq(direct axis, quadrature current) are related to Ia,Ib,Ic phase current?

Thanks for your clarifications.