r/rfelectronics • • Nov 02 '23

Racism in defense industry

11 Upvotes

Hi All,

I have been in the US defence industry as an RF engineer for about a decade now. During my time I saw a lot of racism/discrimination against PoC/immigrants from Asia/middleast/etc. This manifested through either hiring practices or through office politics/culture, etc.

I have worked at two primes, and saw similar behaviours in both. Obviously I am not going to band them. I was wondering if anyone else has seen a similar trend? Or was this just a coincidence within the teams I was in.

Edit: To all of you downvoting. Take a good look in the mirror, because this post is about your ilk. Go ahead and downvote, you are only proving the point of the post.


r/rfelectronics • • May 08 '20

I would think with the internet that most professional/commercial communication would NOT be done over RF, so who's using the communication towers like what I linked to, and what are they communicating?

Post image
1 Upvotes

r/rfelectronics • • Aug 31 '26

question Need guidance and help to quickly learn Silicon Photonics MEMS so as to define a problem stament for my applied electronics PhD.

0 Upvotes

Dear all,

I have just started my PhD into the domain of Silicon Photonics and terra hertz RF based MEMS. This is something we are doing for the first time in my group. However, my knowledge of basics in Silicon photonics and MEMS isn't very great.

I want to quickly learn all these ASAP and wanted guidance on what are the right resources to go through which can enable me to reach that level so that I can take up an efficient work for my PhD.

I have got COMSOL installed via my university access and would really appreciate if someone could guide me. Videos, DIY books and anything similar would be very helpful.

I need inputs on texts, and also simulation setup that I can use to go ahead.

Thanks.


r/rfelectronics • • Sep 08 '26

article WTF is a BJT? (PositiveFB)

Thumbnail
positivefb.com
0 Upvotes

r/rfelectronics • • Jul 31 '25

question Is it possible to make an antenna using square waves?

0 Upvotes

They would range from +5V to -5V at 100khz. If needed, I can amplify them to +10-30V to -10-30V. I can adjust the frequency to about 1Mhz if needed, propably even higher, but I'd like to keep it this low.

Questions:

  1. How big would the antenna have to be? 10-20cm?

  2. Is the voltage enough?

  3. Is it useful for data transmission?

  4. What bitrate are we looking at? 1 kilobit/s?

  5. Is the receiver going to be complex?

Please keep in mind that I've never realy touched my head into antenna stuff, so please excuse my bad questions.

Thanks!


r/rfelectronics • • Apr 10 '20

5G oxygen absorption

3 Upvotes

Hey,

There are a lot of conspiracy theories going around now about 5G being dangerous. Being an engineer myself, I am well aware that RF is harmless and doesn't cause cancer and other negative health effects unless in concentrations high enough that it causes excessive heating or burning.

OK, so that's all good, but the oxygen absorption peak at 60 GHz is odd. I think it's probably OK, but I really can't be sure because none of the studies that talk about this effect mention the field strength required to cause it. I think it would be great to have an Rf engineer debunk this because it is the only claim that 5G conspiracy theorists are making that no one is addressing.

https://www.rfglobalnet.com/doc/fixed-wireless-communications-at-60ghz-unique-0001

I know that these frequencies do not penetrate the body very well, but this still could have an effect I would think. There are other studies that show how this makes the hemoglobin unable to absorb the oxygen molecules. So I need to know what concentration is required for this to actually cause problems? Is it a legitimate concern or would the power levels be so high that it doesn't matter?


r/rfelectronics • • Mar 15 '21

RF Engineering is Not Dead

1 Upvotes

Hey ya'll. I know there is sometimes a lot of doubt in the RF Community about job availability. I read this article and it gave me some hope. RF Engineers will always be needed because of changes in the network and technology.


r/rfelectronics • • Jan 12 '26

Indian RF folks — I’d really appreciate your honest take on this.

1 Upvotes

I’m an ECE student graduating in 2026, and I’m trying to understand where RF in India is actually going. Online, everything looks great — 5G, satellites, radars, IoT, antennas — but I want to hear from people who are working in this field here, not from blogs or YouTube.

From your experience: Where is real hiring happening right now in India? Is it more in antenna & RF design, RF testing, telecom, automotive radar, IoT/telematics, or something else?

What skills really matter today? Is strong RF simulation enough, or are companies expecting embedded, Python, validation, compliance, etc along with RF? And honestly…

If you were starting your career again in 2025–26, would you still choose RF, or would you go for RF + embedded? I’m asking because I have to decide what to focus on for the next 1–2 years, and hearing real industry experience will help a lot.

Would really value replies from people working in Indian companies like L&T, Tejas, Qualcomm, Bosch, Tata, ISRO, VVDN, startups, etc.


r/rfelectronics • • Oct 13 '26

We built an LLM specialized in RF component selection and datasheet retrieval. Looking for feedback from RF engineers on this 2-min demo.

13 Upvotes

For the past few months, in our free time, a colleague and I have been building a tool for hardware designers. It’s called ACE, and before moving forward, we’d like to see if it actually makes sense.

The idea stems from a personal frustration. If you ask ChatGPT for the noise figure of an amplifier, it responds with absolute confidence. But it’s not actually reading the datasheet: it just hallucinates the most likely number based on its training data. As a result, you get a value measured at a different frequency, or from a similar model, or a "typical" value presented as guaranteed—and nobody tells you where it came from. It also does math "by eye": one mistake in an RF chain calculation, and the whole result is wrong, written with the exact same confidence as a correct one. You only notice it when the board arrives.

ACE, on the other hand, answers strictly based on datasheets. Every value displays the exact page and measurement conditions right next to it, so you can double-check it in ten seconds. The code handles the calculations using transparent formulas, not the AI model. If a data point isn't there, it tells you instead of making it up.

Right now, it's a prototype: it includes about 1,500 datasheets, mostly RF, and some features shown in the video are still in the early stages.

To the hardware designers out there: would you use this? And what would it take for you to truly trust the numbers? We are especially looking for critical feedback.


r/rfelectronics • • Jul 04 '25

Am I looking for a Unicorn?

0 Upvotes

Is there a device that can detect cell phones over a 1/2 mile radius? Not looking for a room bug sweeper or camera setup, but trying to police a property without wifi.


r/rfelectronics • • May 16 '23

Listening device to hear 2.45 and 5ghz wifi signals?

0 Upvotes

Is there a cheap or easy way to make a listening device that can turn the RF/EMF from wifi routers into something audible?

I like how this Fluke prob lets you hear things through walls (like 120v 60hz ac), you don't even need the tone emitter hooked up for that.. but the probe doesn't hear much at all when near 2.45 or 5ghz signals.

https://www.fluke.com/en-us/product/network-cable-testers/copper/pro3000kit

I badly need to track down some stuff hidden in the walls, but im sure its 500mhz-6ghz.


r/rfelectronics • • Aug 26 '18

Can anybody explain why the relays are used?

Post image
0 Upvotes

r/rfelectronics • • Jan 08 '25

Are American Engineers mediocre?

0 Upvotes

Not intending for this to be a political post, but in the experience of this community, are American engineers mediocre? Why is SpaceX CEO saying things like this?

I'm American, and while I don't think I'm a genius or a prodigy, I feel like I am competent. There has never been a subject matter that I have felt was out of reach or that I was incapable of understanding given enough time and study.


r/rfelectronics • • Jul 28 '26

Too good to be true?

Post image
18 Upvotes

I am VERY new to antenna design and experimenting with hilbert fractilization. In iteration 5 the size went down by 20 percent and the linear gain went up by 25 percent but as u can see the directivity is messed up. Im worried that it just took the energy from the single lobe in the left picture and concentrated it in the 2 lobes so that 25 linear gain isnt even actual gain. Which actually makes sence since u cant create energy out of nothing, i was just hoping maybe it could increase its pointing gain or whatever its called.. Maybe this will only help a rx system.. This is at 2.45 ghz btw but my code can mod it to any freq and iteration.

Theoretically, tunning it will fix the lobe and im debating on wether to spend 15k on a computer to do it since it took Feko over 2-3 hours just to render this or whatever the terminooogy is(i have like over 90 cores in my ic, its the newest I9, and used all of them).

20 percent reduction for patch antennas is enough to make me a billionaire but I highly doubt this is even patenable, also of i cna figure this out im sure its already been figured out.


r/rfelectronics • • Mar 07 '23

Hey everyone, we want to share our RF synthesizer design with all of you.

4 Upvotes

The idea is to create a guideline for highly integrated electronic devices of any shape, moving away from the flat PCB formfactor and fitting electronic functionality into any suitable volume.

Using AME technology to distribute RF signals has a significant advantage. It allows for the smooth transport of RF signals through coaxial lines with a predefined bending radius, minimizing reflections in signal paths.


r/rfelectronics • • 27d ago

How do you actually use AI in your RF work, and where does it fall flat?

0 Upvotes

I've started using AI to cut the grind in my RF work. I am designing an RF T/R module using COTS. I am finding parts that meet a spec using distributers online search or web search. This requires digging out the datasheet page behind each figure, re-running the same numbers after a change.

Some of it saves real time. Most LLMs currently not capable of excluding obsolete parts even with web search ON. I still have to check by hand in the datasheet, because it will confidently quote a figure I can't find in any datasheet. I have actually started developing my own MCPs to do a lot of the manual work. Hopefully open source it some day.

Curious how others here use it day to day:

- Which tasks do you hand to AI now?

- Which ones did you try and give up on?

- What's still fully manual that you wish wasn't? I can add to my MCPs.


r/rfelectronics • • Jun 18 '24

question Friend claims their wifi modem and a nearby cell tower emit levels their EMF reader shows as above the safe limit

2 Upvotes

I don't know the science of radio frequencies, but in general I NEVER trust ideas that are alternative to normal scientific understanding, because science is an extremely reliable framework based on the research of countless people using rigorous testing and knowledge vs an individual or group of individuals using unreliable testing or knowledge. In this case, my friend says the radio tower reads 650, and the modem reads 2000, both of which are near or outside safe human limits. Purely due to the fact these radiotower type theories arent taken seriously within science, what's likely happening here? Is there a measurement a modem typically emits that could match around 2000? And have they gotten it mixed up with another kind, or found an unreliable source on why that level is unsafe. Is there no measurement that would come from a modem reading around that so the EMF reader is likely broken?

I'm curious in general the science behind EMF readers. Again I'm moreso basing my doubt on the fact humans are generally good at figuring out what's unsafe. We have the understanding of the electromagnetic spectrum to map black holes, yet it's up to some individuals to figure this out using a device you can buy on eBay? I don't buy it


r/rfelectronics • • Aug 13 '21

question At what frequency range does it become difficult to travel through solid objects like doors and walls?

2 Upvotes

At what frequency range does it become difficult to travel through solid objects like doors and walls? I don't want answers like it depends on the signal strength, most normal people will not have the power to increase the signal strength to a level where the signal might damage a wall or heat skin or cause a power outage in the building.

Give me a frequency range for normal materials out of which walls are made of in your classroom, etc. Not for metals like copper, etc.


r/rfelectronics • • Aug 25 '24

question PhD about anechoic chamber RF compliance

0 Upvotes

I found a PhD Thesis (written at the University of Southern Queensland (Australia)) about an anechoic chamber performance regarding electromagnetic compliance. It has:

  • 23 used citations.

  • 0 publications in peer-reviewed journals.

  • The University of Southern Queensland does not accept any responsibility for the truth, accuracy, or completeness of material contained within or associated with this dissertation.

Can anyone explain how this kind of quality content is even possible? Did he just bought his PhD?


r/rfelectronics • • Feb 02 '23

question How is the number of turns in a balun calculated?

1 Upvotes

I haven't been able to get to the bottom of this with google, so here I go:

I want to make a 1:1 balun and it needs to be decent at what's left of the TV UHF band (470-700Mhz). Probably on a toroid.

Given a known wire thickness and bandwidth requirement, how would I go about calculating the core size, number of turns, etc?


r/rfelectronics • • Jan 25 '26

question Current State of AI in RF Engineering

Thumbnail reddit.com
2 Upvotes

r/rfelectronics • • Mar 19 '24

usb over 5-10 kms

0 Upvotes

A remote device with a usb port needs to be accessed from a computer sitting about 10 km away. The only acceptable means is via a wired connection. No budget for buying transceivers or converters. Any thoughts on this?

Update: Something on the lines of this (https://www.digi.com/resources/library/data-sheets/anywhereusb-plus-ds?view=fullscreen) but cheaper with a maximum of 2 ports in one location


r/rfelectronics • • Jul 16 '26

Hairpin Filter with AI control of MWO

Post image
0 Upvotes

Finally got a screen recording with audio. It's LONG so use the timeline to click through.

https://youtu.be/1wjlHlji9Os?si=eL15s-qo4pIaBGjy

Continuing from last post, I asked it to do a hairpin topology and it did the electrical prototype correctly but then it had a lot of trouble with the layout as it did NOT attempt to use multi-coupled lines, rather staggered coupled pairs, therefore attempted to create a physical layout using simple bends. Thus I halted the attempt. It was able to properly arrange the schematic elements using visual feedback.

I then started fresh and told it to just go research a filter and build it, and it decided upon an "open loop" topology which was really just a hairpin. This is where things get interesting. I switched to the 5.6 Sol model (the top model). It scanned the MWO examples directory, found a hairpin example, parsed that example using the API, then re-synthesized that example on a new substrate with a higher order topology.

This is where the Sol model really improved things:

Really good at visually checking all the junctions.

Intelligently tuning different sections depending on response; resonator length, coupling tap adjustment, gap spacing. It is NOT running a raw numerical optimization, rather truly intelligent tuning. Was able to process about 3 tunes a second in the simulation and read-back loop.

Next going to switch to amplifiers or antennas. It’s probably at the point now it can be let loose to run overnight on synthesis tasks, though a couple of times it halted after EM sim was complete and needed to tell it to resume.

Codex summary:

In this session, I used Python automation and the Cadence AWR Microwave Office API to design, tune, and electromagnetically verify a compact folded open-loop hairpin bandpass filter centered near 4 GHz.

The project followed a staged workflow:

  1. Configure metric units, substrate, copper layers, materials, and the EMSight stackup.

  2. Verify the electrical prototype.

  3. Create and tune the physical microstrip model.

  4. Snap and visually inspect every layout junction.

  5. Simulate the EMSight test bench.

  6. Apply an EM-derived correction and verify the final response.

I independently found an installed Cadence hairpin-filter example and inspected it through the API. This provided its exact element types, parameters, positions, rotations, nodes, and connections. I also simulated the example before adapting its topology.

The reference used M10CLIN and M8CLIN multi-conductor coupled-line models with MTEEX$, MUBEND, and MOPENX elements. Its proven topology was adapted for a 4 GHz RT/duroid 5880 design.

Tuning used numerical S11 and S21 data. Each candidate was evaluated for return loss, insertion loss, cutoff frequencies, cutoff midpoint, and nearby stopband rejection. The filter center was defined by the midpoint between its cutoffs, not simply the S21 peak.

Resonator length primarily controlled center frequency, coupling gaps controlled bandwidth, and feed geometry controlled external matching. Symmetric parameters were tuned together using coarse searches followed by finer local sweeps.

API connectivity alone was not accepted as proof of correct geometry. After every physical change, the layout was updated, snapped, redrawn, and inspected at close zoom. The input, every internal junction, and the output were checked for red X markers, gaps, copper overlap, narrowed coupling gaps, overhangs, incorrectly oriented transitions, and corners bridging adjacent resonators. The mirrored output was checked independently.

The EMSight mesh was selected from the smallest important features. An anisotropic grid used 0.05 mm resolution in the critical direction and 0.10 mm in the less critical direction, resolving the coupled geometry while reducing simulation size.

The transverse enclosure was reduced to about two substrate heights beyond the copper. The input and output walls were aligned with the edge-port faces. This compact enclosure was a project-specific runtime compromise.

The EM sweep used coarse spacing in remote stopbands, moderate spacing near the shoulders, and fine spacing through the passband and transitions—approximately 0.25, 0.05, and 0.01 GHz, respectively.

The first EM response was slightly above 4 GHz. I preserved the baseline, created a separate tuned copy, and increased the common coupled-leg length to 10.4 mm.

Final EM results were approximately:

• Peak S21: −0.95 dB at 4.00 GHz

• S11 at 4.00 GHz: −29.7 dB

• −3 dB passband: 3.91–4.15 GHz

The active Microwave Office windows were kept visible and tiled throughout the work. The narrowband graph was shown during tuning, close-up layouts during junction inspection, and the EM structure and solver status during simulation.

This workflow combines API inspection, numerical tuning, visual layout verification, and EM analysis. The API provides precise data, while graphical inspection catches physical problems that connectivity alone cannot reveal.


r/rfelectronics • • May 31 '24

How is it possible that if I plug my USB hub, my WiFi performance degrades? I think it's because since this USB hub is not powered, it asks USB much power creating EM field which can cause interference to WiFi? But for having this the EM field should be the WiFi one so I don't think it's the case

0 Upvotes

This USB hub has nothing attached. It's empty.

I don't get how is it possible that it's creating this interference to a WiFi band that should not at all be affected by a EM field generated by a power which is continues current so 0Hz.....