r/resinprinting • • 23m ago

Question For everyone that makes figures how should I start learning to paint them

1 Upvotes

Just got my printer and my goal is to make my own anime figures and since black Friday is coming up planning to but everything i needed. What kinda paint should I get as a beginner I was looking at nicpro set just for all of the and also vellego sets but there kinda expensive. I know i need brushes for the small details but should I also get a budget airbrush kit like one of the gaahleri kits if I get the airbrush im just gonna get the vellego bundle with the cleaning pot and clear but I really just want to know everyone's opinion.


r/resinprinting • • 37m ago

Promoting Paid Item/Service Printed my new Undead Hound (Free Pre-Supported STL)

Thumbnail
gallery
1 Upvotes

Just got this one off the printer. Sculpted by hand in ZBrush. I left a short process video in the comments if you're curious how it was made. Pre-supported, in 32mm on a 25x35mm base and in 75mm (hollowed). This one is free, and the Stalker and Mauler from the same pack are in the store too.


r/resinprinting • • 1h ago

Company Sponsored/Affiliated Free 3d Printable Mutated Mage

Post image
0 Upvotes

Hey guys, it’s me again! Just sharing another free mini. This one’s the Mutated Mage😄  

Free download: mmf.io/o/y878215

He’s part of our School of Magic collection, which is live on Kickstarter if you’re curious to see the other minis. And mods, if this post is outside the rules, I’m happy to take it down. :)


r/resinprinting • • 2h ago

Question Is this FEP still good?

3 Upvotes

I'm new to resin printing and got a used spare vat that came with a FEP still mounted and was wondering if the film is still good for use.
If still good, will those wrinkles show up on the prints?


r/resinprinting • • 3h ago

Promoting Paid Item/Service Print photos of our fourth set of catrines

Thumbnail
gallery
10 Upvotes

Fantasy characters inspired by Mexican folklore and pop culture!


r/resinprinting • • 5h ago

Fluff Resin Printer Safety Livingroom

Post image
1 Upvotes

r/resinprinting • • 6h ago

Fluff HeyGears G1X - Slap in the face

1 Upvotes

It's one thing to delay a product, it's another thing to bury it as bullet #3 in an announcement and write it like it's a good thing. Start of shipments were slated for December. Now they're saying they'll have 300 units in March. 0 people have mentioned it and the Youtubers that demoed this BS, have made no remarks.

There are 4000 backers, 300 units for March, means they down and outright lied.


r/resinprinting • • 7h ago

Question Resin printing goes wrong. How it can be fixed?

Thumbnail gallery
1 Upvotes

r/resinprinting • • 13h ago

Troubleshooting Clumps of resin during wash

Thumbnail
gallery
2 Upvotes

Hi all,

I’m relatively new to this hobby and I tried to print this large hollow piece on my Elegoo Saturn 4 Ultra, and it came off the build plate looking great. But during washing, thick, rubbery clumps of resin stuck to the basket, the hollow piece, and the other miniatures in the same batch. I cleaned everything by hand, and the prints turned out fine. I’ve been resin printing for over six months and haven’t seen anything like this before.

There may have been some resin buildup in my wash tank already, but the amount of residue was sudden and unusually large. My suspicion is that the hollow piece held more liquid resin than I realized and released it into the bath. I’ve attached photos of the piece and the residue.

For this specific part, is the large opening shown in the photo meant to drain the entire cavity? Are there any internal pockets that can trap resin in the supplied print orientation? If you’ve washed this part yourselves, how do you orient it to drain and flush it before putting it in the main wash bath? Would you recommend adding a drain or vent hole, and if so, where?

Thanks!


r/resinprinting • • 14h ago

Showcase Devilman - Tanuki Figures NSFW

Thumbnail
gallery
39 Upvotes

r/resinprinting • • 14h ago

Showcase Lady - Devil May Cry

Thumbnail
gallery
85 Upvotes

r/resinprinting • • 14h ago

Question elegoo saturn 4 ultra (12k), heygears rs, anycubic p1 or uniformations gk3?

0 Upvotes

all of them are on sale right now for around 500


r/resinprinting • • 16h ago

Question Best 2026 resin printer for 1000 euros

1 Upvotes

Hello!
What resin printer is worth buying in 2026 for around 1000 euros?


r/resinprinting • • 17h ago

Question Drugi raz ten sam błąd😒

Thumbnail
gallery
2 Upvotes

Gdzie jest problem Slicer? Oryginalny pendrive? A tak mi na niej zależy


r/resinprinting • • 19h ago

Troubleshooting Best calibration for a Mono X?

0 Upvotes

I've been really struggling to calibrate my anycubic Mono X, between the UV strength and the actual print settings. I'm printing with anycubic ABS -LIKE + and using Lychee slicer.

Does anyone have it dialed in that can lead me in the right direction?


r/resinprinting • • 20h ago

Question Uniformation gk2 adhesive replacement

1 Upvotes

Hi everyone, so I've been looking at the tutorial videos and reading some stuff online about how to replace the gk2's nfep but can't find much on the adhesive layer. Iv asked their support who say any double sided tape should do but reading here Iv seen some say you need to use strong ultra thin stuff (3m 15mm tape comes up a couple times) otherwise you can get a leak after a few prints with the nfep pulling away, but others say it's not needed at all and it's only used to help with the installation of the nfep.

I wanted to see if anyone else who has used a gk2 and has replaced their nfep put on new adhesive, and if so what did you use? Did you find it had to be something strong like the 3m tape or was something as normal as sellotape/scotch tape good too?

Also sorry if I've mis worded my question, I'm not the best at writing.


r/resinprinting • • 21h ago

Fluff Me when my printer warns me the FEP has 30,001 layers on it

55 Upvotes

r/resinprinting • • 21h ago

Question Looking for someone in Berlin with a resin printer

1 Upvotes

I'm looking for a private person in Berlin who has a resin (SLA/MSLA) printer and could print a detailed piece for me. I'm happy to pay for it


r/resinprinting • • 21h ago

Troubleshooting Prints not even starting

Thumbnail
gallery
3 Upvotes

Just got a resin printer and had a successful first print. Sense that initial first print everything that I send to the printer. Goes through the entire printing process. Then when I check the build plate. Nothing. I even used the previously printed file on the printer to reprint that successful initial print. This time it didn’t work. I don’t know what I’m doing wrong. I also made sure that there wasn’t cured resin bits in the pool. From what I can tell there is nothing. Any help would be appreciated.
Thanks


r/resinprinting • • 21h ago

Question Resinwanne in die Wash and Cure Station?

1 Upvotes

Kann ich die Wanne auch in der Station sauber machen oder ist das schlecht für die Folie/Wanne?


r/resinprinting • • 21h ago

Question Annoying print lines on saturn 16k

Thumbnail
gallery
0 Upvotes

Hi everyone, i have for some time already wierd print lines, appears randomly in different print levels etc. Models are printed without hollowing as intended, sometimes i have the same on 32mm scale aswell.....any guess?


r/resinprinting • • 23h ago

Question Advice on the best way to wash/cure this structure?

Thumbnail
gallery
4 Upvotes

I'm printing these towers of plugs for a project I'm working on. They are printed in Inslogic 70A flexible resin. I've got the design and print settings down and they work well, but I'm going to be printing these en masse. Like, each tower has 441, and I'll be printing several towers at a time. I'm trying to figure out an efficient process for washing and curing them though. Obviously they are fairly packed together. Each plug is connected to the one above it, and each column is connected by thin horizontal connections to the adjacent columns (for support during printing given the nature of flexible resin). I currently have an Anycubic Wash and Cure Max 3, which sprays rather than submerges, and I'm worried that that won't actually be enough to penetrate through to the inner most columns in the tower. Same with curing. Am I going about this design all wrong? I'm trying to maximize the plug count per run, but I'm brand new to resin printing in general. Any advice would be completely welcome.

Edit: lmao, who’s going through and downvoting each of my comments instead of just trying to help me work out the process here 😂


r/resinprinting • • 23h ago

Promoting Paid Item/Service Print tests for the 1:72 scale Object 775

Thumbnail
gallery
7 Upvotes

Hi everyone, here’s an update on the project.

I’ve had some very satisfying results from the print tests for the Object 775—a model I created as an additional reward for "early bird" backers of my Kickstarter campaign.

I found the Object 775 to be a fascinating project. While modeling it, I actually had to fight against my own common sense; the turret is so incredibly flat that it felt quite strange to look at! It’s a unique vehicle—a tank designed with a completely different philosophy compared to a standard MBT—and I’ve tried to recreate it as accurately as possible.

The model is high-quality, with separate parts to make 3D printing easier. I’ll share the final, complete result with you soon.

I don’t want to spam the group; I simply hope that this community—centered around a hobby I dedicate so much time to—might offer some support. I’m truly grateful for the support I’ve received so far, and I’m very open to any suggestions or constructive criticism—all advice is welcome! Thanks in advance.

If you’d like to learn more about the project, see more of this vehicle, or check out the rest of the collection, you can take a look here:

https://www.kickstarter.com/projects/vbertz/secret-soviet-armored-program


r/resinprinting • • 1d ago

Promoting Paid Item/Service If it bleeds, we can kill it. 🩸Predator printing & assembly process

97 Upvotes

Test print of Predator created by Bulkamancer Sculpts.

Sculpted by Valentina Iudina.

Printed, filmed & edited by Takokumono.

Printed on Anycubic Photon P1 & ELEGOO Saturn 3 Ultra using Conjure Sculpt Beige resin (27 pieces, 273 ml).