r/prusa • • Dec 29 '23

Why are prusa's filaments so expensive?

0 Upvotes

In Czech republic, I can buy black PLA for 300 CZK (12€) but prusa's PLA for 600 CZK (24€)?
I understand there is some visible changes but not functional. Do you have some explanations or is Prusa simply too greedy?


r/prusa • • Sep 22 '21

Am I the only one thinking the MK3S assembly is a hot mess?

4 Upvotes

*dons fireproof suit*

I have assembled a LOT of mechanical kits over the years, ones with electronic parts and mechanical parts, ones with small pieces and tight tolerances. This is my fifth 3D printer, and the 4th which was a kit to assemble. This MK3S+ kit has been the worst in a long time, and I still have pages to go.

On the positive side, the printed parts look like they've been printed well, and are hardy against abusive forces. The machined parts are also high quality and the part counts are all accurate. The instructions are clear enough about what needs to be done.

It's just the design which is a disaster, completely ignoring the ergonomics of the assembly process. The designer wanted to show how clever they were, and all they demonstrate is how they don't know how to design assemblies.

  • there are several places in the assembly where you have to carefully distinguish very similar bolt lengths (3Mx18 and 3Mx20 in the same bag, for instance) instead of designing for a common bolt length; good thing I am meticulous but you should not have to address user complaints with sentences in the instructions which read "if you already used the 3Mx20 elsewhere, dig into the spares bag"

  • the Y axis linear bearings mount to the deck using crappy little sheet-metal clips; I bet the guys at the factory have a neat little jig which helps them manage a delicate oily smooth cylinder, two 3mm nylock nuts, two short 3mm bolts, a piece of tin and a deck cut in the shape of four St Andrews torture crosses, but not everyone has a soft-jawed vice or even a small wrench that would do better than the included pliers

  • the Y belt is cut at the factory exactly at the right length to the tooth, so if you already folded and secured the first end with just 3mm extra hanging out, you won't have enough on the second end; the harm of having an extra 10mm on this belt is non-existant because both ends could just hang out of their clips

  • the X belt is cut at the factory to be about 44mm too long, and you will need to trim the length while the entire assembly is held under tension (all amidst the five cable pigtails hanging in your way) because the toothed slot ends are so conveniently terminated inside the head instead of doubling back out like the Y belt

  • the X stepper motor has tension adjustment slots that allow for about 1.5 teeth of adjustment; if these slots were longer, the difficulty of cutting the X belt's length would have also been alleviated

  • the extruder head has way too many parts, each one needing extra space to accommodate buried square nuts or tunnels for bolts to hold it together; it could probably be made lighter and simpler if it were just two major halves

  • the nylon guide: just press-fit the tip of this slippery noodle into the back of the extruder head which is only secured by zip-ties on one of the rails... until it's snug enough to pass a pull test; it's not clear that the design really needs a cable guide at all

  • the cable shroud should be left off until functionality is tested; there are a lot of parts of this kit which feel like it will be a PITA to reverse if something isn't right and this is the worst example

  • the electronics assembly is performed after the motors and hot-end, after extruder parts are bolted shut, after zip-ties are cinched; this seems backwards to me, because a good controller can help you test things along the way in a software mode for assembly (test Y axis, test X axis, test Z axis, sync Z axis, check fans, check filament sensor, etc)

Hey, I have high hopes about the printer working well, and many people seem to like the overall functionality vs other printers on the market. I just think that the assembly part of the design does not earn the same level of praise. I hope whoever is laying out CAD files for the MK4 will take their cues from Toyota more than from BMW: make parts accessible, make assembly reversable, make functional testing possible as early as possible, use common parts, make the shapes of parts aid in the assembly rather than fight the assembly, and so on.


r/prusa • • Dec 25 '21

Issue Hey Reddit. Having a rocky start.

Post image
0 Upvotes

r/prusa • • Aug 16 '21

What sort of defects did your printer have?

1 Upvotes

I took 10 days to put mine together. Not straight through, obviously. I have had to take parts of it (esp. extruder) apart and put them back together many times since then. Major defects:

  1. Filament sensor only works when the top screw behind it is loosened just a little.

  2. Tried to recover a print after a crash (that was my fault), instead of starting to print again, the nozzle just moved to the place where it left off and embedded itself in a giant blob of filament it then couldn't extract itself from, thus causing a clog.

  3. Apparently, the firmware can be corrupted when flashing. This caused many problems, esp. with incorrect belt tension readings.

I'm hopeful, now that 1 is understood, 3 appears resolved, and I'm ignoring 2 (maybe it was caused by 3), that things will go well. I def had some serious issues with print quality on a tall/ not narrow print.

Now, I know I didn't do a perfect job. I broke a Y rod holder and plugged the IR sensor in upside down (which also made me mad, since I sent a pic of the way I plugged everything in to support before I turned it on and they said it was correct). I also had my belts a little too tight and maybe the X roller a little too loose, but I was really hoping that this printer would live up to the hype and I've been sorely disappointed.

I also asked support to check if a gcode was supported (M702 to unload filament at the end of a print - I didn't want to test it myself, because I wasted one of the spare bowden tubes by clogging it trying E-100 and I don't know how to get them shaped like that) and they promised to test it and get back to me and never did, then the guy in charge got all condescending and told me not to mess with the tested gcode.

Anyway, someone responded to my post about wanting to throw the thing out the window when I was building it and I was triggered and needed to vent.


r/prusa • • Apr 13 '22

Research on 3dprinter users needs for new product

0 Upvotes

Hello I am cdeveloping a new product for 3d printing and I would really like to have some information about what user needs actually are so I made the questionaire below.
It will only take 2-3 minutes

https://docs.google.com/forms/d/e/1FAIpQLScr9Y0irxekWaj7uLhoTvcoq06p8BNXCRQwd7F3cZTrWJ7iKw/viewform


r/prusa • • Jun 16 '22

Best CAD program for 3D printing

1 Upvotes

Hey guys, need some good advice about CAD software. I’ve had my printer for just over a year and have only used Tinkercad. I can do quite a lot with it but I’m ready to go to the next level. I was looking at F360 but I’ve seen online reviews stating it’s expensive and the free version is not very useful.

What do you use / think is the best CAD software for 3D print designing.

Here are the features I’m looking for:

  • Work environment as similar to TC as possible.

  • More advanced features like camphering etc.

  • NOT exclusively cloud based so I can save project .3mf files.

  • Free or moderate subscription

Thanks.


r/prusa • • Feb 13 '24

Issue Prusa Store Compromised?

0 Upvotes

Hi - throwaway account for privacy reasons...just putting this out there so other people can be aware:

Last Thursday, I purchased an MK4 printer (assembled) from the Prusa store. Within minutes, my bank sent me a text asking me to confirm/validate the purchase because it was an outlier event. No worries, I approve and go back to what I was doing.

A few minutes later, I got a second notification, with the same title but this time, there were three transactions all with an iOS developer company in China for $40, and would you please approve?

Wait, wut?

I contacted my c/c company and I learned that dozens of separate charges, totaling well over a grand, to three companies, appeared on my card within minutes of the transaction with Prusa. The card is declared compromised, and canceled, and I must call my bank the next morning to arrange for a replacement. No other charges had been posted to my card, previous to this, for almost two weeks.

The next day, get the new card ordered, no problem, and I decided to reach out to Prusa tech support to let them know about the potential threat, to request to talk to someone in legal or fraud, and all I received from Level-1 Support was a blow-off response:

  • we have no access to transactions

  • payment gateway is a third party; not our problem

  • contact the third party (I have no idea who they are, of course)

I reply, cordially, that afaic, Prusa is on the hook as it's their company on my bank statement, not some unknown 3rd-party payment portal that they chose to represent them. I also point out that this is a criminal issue, not a support issue, and also not an issue for the devs. Please escalate to legal or fraud.

(aside: I'm a retired developer who's written payment portals. Support can get access to these APIs - I did when I was Support - and some will gift engineers and support with access to the prod db. Point: When the payment process is compromised, you don't share details with folks who have opportunity.)

Support comes back with: I need all the details if we're going to do anything about this. One sentence.

I reply, respectfully, that again, I would like the problem escalated - that this isn't a support or engineering issue, and for a third time, I am declined.

This posting is just to let you folks all know that the payment portal on the Prusa store could potentially be compromised resulting in unauthorized charges being made to your card.

tl;dr: Always use your credit card, never debit, for online purchases as even the most trusted and beloved retailers can be compromised.


r/prusa • • Apr 20 '23

New mk4 owner

0 Upvotes

I bought a prusa mk4, 8 days ago I placed the order and they have already charged me from the bank. When I placed the order, the delivery time was 2 to 4 days, the status of my order has been paid since day 1, no change since then. I have contacted Prusa and they tell me that they cannot give me the shipping date. Is this something normal in Prusa?


r/prusa • • Jun 22 '20

We convenienced others at your inconvenience

Post image
0 Upvotes

r/prusa • • Feb 24 '22

Issue Can’t remove the fucking cable

0 Upvotes

I’m trying to remove a cable from my prusa printer and can’t get it out of the Einsy bord!


r/prusa • • Sep 20 '20

How many parts to build the i3 mk3?

0 Upvotes

I just started building the Prusa i3 mk3 and I’m curious as to how many parts in total there are. This is mostly so that I can flex it to my friends if I’m being honest. Estimates would be great too!


r/prusa • • Jan 17 '24

Issue New to 3DP, have MK3S+ and no idea where/what to adjust.

Post image
0 Upvotes

I really need suggestions. I've never seen one print, but it ain't lookin right. 😂


r/prusa • • Dec 06 '23

Rotary extruder test

Thumbnail
youtu.be
0 Upvotes

r/prusa • • Feb 06 '25

Question MK4S or MMU3, you can’t have both.

0 Upvotes

Hello everybody, I have just angrily realised that after upgrading to the MK4S there is no point of buying the MMU3 kit. Because you can’t use the fast nozzle from the S kit. I wish that the customer service guy which I asked on Christmas had told me before buying them, because I told him that I would buy both things and he said that it was a great idea. And now I end up having to use either one or the other. I still have the MMU3 inside the box and I haven’t unboxed it yet, but I am thinking of selling it. What are your thoughts? Many thanks


r/prusa • • Apr 06 '23

MK4 Shipping Thread

0 Upvotes

I wasn’t sure if this would be permitted in r/prusa3d so putting it here instead. I figured a thread for everyone to post when they ordered, their order status, and where they’re located might help paint a picture of how MK4 orders are being fulfilled since we’re not getting any details from Prusa at this time as far as expectations. It would be helpful for everyone to update their replies when the status changes too.

Order Date / Time: 3/29 4pm Eastern Time Location: NY, USA Order Status: As of 4/6/2023 - “NEW, deposit paid in full, no delivery estimate”


r/prusa • • Jan 07 '22

Show and Tell Found it interesting the motors turn on the screen

0 Upvotes

r/prusa • • Jun 03 '23

Is it good first layer?

Thumbnail
gallery
3 Upvotes

I just assembled my Prusa i3 MK3S+ and trying to do the Live Z height but not sure what a good result looks like


r/prusa • • Mar 04 '26

My first Prusa!

Thumbnail reddit.com
0 Upvotes

r/prusa • • Dec 09 '25

Question Core One L dealbreaker?

0 Upvotes

Grateful for an experienced recommendation here for a potential Core One L purchaser, given my use-case.

Currently own a Prusa Mini, run it 24/7 for 3 years, all black or white PLA, fed from a standalone heated drier box that is always on. Final print is heat-shaped by hand, painted, washed, waxed, and sold. My items are custom art pieces, Blender/CAD and expensive (around $400 apiece), so I’m not looking for a thingiverse factory. I can’t make things fast enough to keep up with orders, thus my thought of upgrading. The cost of a printer isn’t a consideration. Core One L is attractive for higher quality prints, faster, more prints at once, less post-production, and the potential to do ASA with acetone fuming.

The Core One L checks every box but one: the lack of an integrated filament heater. I can’t fathom buying something the size of a dishwasher, and out the gate having to feed my PLA from a separate heated box. I have seen the mods, the snap-in dry boxes. But they are not heated. And I’m utterly convinced that pre-heated and bone-dry PLA is a massive predictor of the quality I get from my current setup. And that quality is why I charge what I do.

Prusa themselves says that the dryness of the PLA is a fundamental component of quality. My experiments agree. I suspect that no amount of CoreXY or direct drive or chambered temperature regulation can overcome even brand new PLA humidified for 6 hours out of the shrink wrap. Even if it inside the Core One L’s little plastic door, passively heated by the bed.

Does anyone have any thoughts on my predicament, recommendations or alternatives? I just can’t shake the idea that I’m immediately Jerry-rigging a $2000 machine out-of-the-box for the most basic, fundamental quality predictor.

Thanks kindly everyone.


r/prusa • • Apr 20 '26

Quick survey

0 Upvotes

Hi, I’m collecting information about the maker and 3D‑printing community to better understand what types of projects are most suitable (mechanical, modular, parametric, electronic, etc.). This survey is anonymous and takes 1–2 minutes.

https://forms.gle/5wCMs6nPBHkv36Er9


r/prusa • • Nov 06 '18

the best upgrade kit?? Prusa i3 bear review

Thumbnail
youtu.be
0 Upvotes

r/prusa • • Sep 12 '21

Bought a mini, what's next?

0 Upvotes

So I just bought a prusa mini. I wanted to build some 10/22 receivers, and the price of the printer, vs the price of buying new receivers made it seem like a not terrible idea to just buy the printer and make them. I'd spend like $200 extra, but I have a brand new 3d printer. I bought the preassembled version, only because the estimate for me to get it was 3-5 days vs 3-4 weeks. It should be here later this week. Once I pull it out of the box, what should I do? Is there any software I should download in advance? I already have the receiver file. Are there any prusa specific video guides I can watch to familiarize myself with the mini, so once it's here I can just get started?


r/prusa • • Apr 05 '23

Issue Bad quality printing

0 Upvotes

My roommate has a Prusa i3 mk3 and has been having issues with the printing quality, it seems to move or shift with each layer it prints. It never actually seems to accurately print over the previous layer. It has been calibrated countless times by ourselves and by some technicians so that is not the issue. I'll attach some pictures of a test we ran maybe someone can help. thanks


r/prusa • • Oct 05 '21

What type of connector is this on the prusa MINI?

Post image
0 Upvotes