r/projectcar • • 3h ago

Build Progress Got It Moving

Thumbnail
gallery
95 Upvotes

After a couple months of trying to work on this project car on my own, I had to call in reinforcements (my grandaddy and his friend). I wanted to hold off on telling my grandad and dad because I already knew they were gonna say it’s a waste of money and a dumb idea, but I already had my mind setup lol. The original owner of this 84 Camaro passed away over the summer and his buddy that I got the car from couldn’t answer many questions for me. A few things we did were swap the starter, install the distributor and adjust timing, new accelerator cable, rebuilt the carburetor (street avenger) and come to find out there weren’t any pushrods or rocker arms in the engine when I got it! Of course we had to change the oil and fuel also the filters and pumps (car was sitting for 10+ years since the original owner got sick). After swapping all the above, we were able to drive a few miles to the gas station and Auto Zone, just to put a couple of miles on it before actually calling it good. The main things I need now are a couple of vacuum hoses and fix the skipping, the rest are kind of minor like a new hood or a hood scoop, fixing the headliner, paint etc. If anyone has any recommendations around Atlanta, please let me know. I’m hoping to have everything wrapped up pretty soon and at least be able to bounce around a good bit on Thanksgiving lol


r/projectcar • • 9h ago

Finally 'finished' my rocker panel rust repair

Thumbnail
gallery
136 Upvotes

Rivets instead of welding because I suck


r/projectcar • • 11h ago

86 Yugo's. The red one still runs, I think the white will end up being most parts. First project cars, anyone know where to uh... start?

Thumbnail
gallery
160 Upvotes

r/projectcar • • 5h ago

Am I crazy?

Thumbnail
gallery
24 Upvotes

Hey yall I just came across this and well I’ve been looking for an sn95 or new edge mustang for awhile now and even more specifically a cobra. He says there’s no major rust or rot just surface stuff, it’s a southern car, paints faded, small oil leak. I think this could be a very good deal (assuming the motor or something serious isn’t actually wrong with it) just wanna hear some other thoughts on it. Thank you in advance


r/projectcar • • 4h ago

My winter project

Thumbnail
gallery
18 Upvotes

This crusty hotrod has been sitting in the corner of my shop for the last year. I’m going to do a burnout by spring or I’m going to die (of hantavirus) trying.


r/projectcar • • 4h ago

Shitposting We put our lives into machines that take away our unspoken pains.

3 Upvotes

If you wanna see more follow along for the build! Check my page for YouTube and tiktok I do update there more.


r/projectcar • • 12h ago

What car should be my first project car for a fun rally?

9 Upvotes

Hi, I'm moving to a new apartment, which comes with a garage. The garage is 5.65m long, and 2.45 and 2.95m wide (the front and back are different in width). Since the garage isn't big, I'm thinking of getting a hatchback to wrench on and get it ready to go on a fun rally (pothole rodeo). Any suggestions for any particular make and model? I live in Germany, if that's of importance.

Is wrenching possible at all in my garage?


r/projectcar • • 1d ago Bravo

My first try at actual bodywork.

Thumbnail
gallery
559 Upvotes

‘98 4Runner with 327k miles, 5 speed, with a factory rear locker(currently re-installing). Wasn’t gonna let this rust be the end of the car, and the frame is super super solid.

To 30 more years!


r/projectcar • • 5h ago

Has anyone here gotten a state issued vin tag, specifically in Wisconsin?

0 Upvotes

Hi everyone, today I bought the remains of a 1927 Ford model T, I'm going to get a Wisconsin bonded title for it and make a T bucket out of it. However, the seller put the engine number on the bill of sale instead of the frame number. They are off by ONE digit. The frame ends in a 5, the engine in a 6. I am assuming it was an assembly line mistake, but anyway, since he used the engine number I have to keep that engine around until I can get a vin tag matching the number, because otherwise the title I get will not match the vehicle.

I tried getting him to put the frame number on it instead of the engine number but he was a major pain in the ass seller, so I'm kind of lucky that he even wrote me a bill of sale.

But anyway, back to the point of the post, has anyone here gotten a Wisconsin state issued vin tag through the DMV? I.was trying to look up the process but couldn't really find much. What's the chance that a Ford dealership would make one for me if I threw the engine in the frame (seller removed it yesterday for some reason 🤦) then tossed the car on my trailer and took it to the dealership? Afterall, it is a Ford.


r/projectcar • • 5h ago

Build Progress Heart says 944, head says NB Miata for a usable project

1 Upvotes

I'm stuck between two cars I found locally and could use some outside perspective.

First is a 1987 Porsche 944 with the 2.5 NA, 5-speed, and about 140k miles. Body is solid, interior needs work, engine turns but hasn't run in a couple years. Seller wants $3k. The second is a clean 2002 Miata NB with the 1.8, 120k miles, soft top is shot but the rest is decent. Asking $4k.

I already have a daily so this would be the weekend/fun car, but I want to actually drive it once it's sorted instead of it sitting for years. The 944 appeals to me way more on looks and character, and I'd probably do suspension, brakes, and maybe a 3.0 swap down the line. The Miata is obviously the easier platform if I just want something reliable and modifiable without headaches.

Anyone been down this road? Did the 944 end up being more trouble than it was worth as a driver, or is it manageable with normal maintenance?


r/projectcar • • 9h ago

Troubleshooting Help Fuel Delivery Issue - 73 Mach 1 351C

2 Upvotes

Alright, this might be a long post, but I figured the more information I include, the better.
I’ve got a 1973 Mustang Mach 1 with a 351 Cleveland 4V, an Edelbrock carburetor, and a mechanical fuel pump (believed to be a NAPA replacement). The fuel tank and pickup are new, and the pump was supposedly unused when I got the car. I’ve driven it plenty of times without this issue.
I recently took it on its longest test drive yet, about 20 minutes to a friend’s shop and another 10 minutes back. On the way home, the engine started bogging down and losing power, almost exactly like it was running out of gas. Eventually, it sputtered out completely and wouldn’t restart.
I initially assumed I’d run out of gas, but I checked the tank and there was plenty of fuel.
I tried adding a little gasoline directly to the carburetor, and the engine would start and run just long enough to burn through what I’d added before dying again. Eventually, I got it home and started troubleshooting the fuel system.
Here’s what I’ve checked so far:
Tank to fuel pump: I disconnected the rubber hose at the mechanical fuel pump’s inlet, and it was full of gasoline. I then connected a hand vacuum pump to that hose and successfully pulled a continuous flow of gasoline all the way from the tank, through the hard line, to the pump inlet.
Fuel pump to carburetor: I checked the rigid metal line running from the pump to the Edelbrock carburetor and was able to pass fluid through it without any apparent obstruction.
Fuel pump: I haven’t tested the actual output pressure yet. However, when I disconnected the metal line at the carburetor and cranked the engine, I could feel what seemed like pressure pulses at the end of the line, but no gasoline was coming out.
After pulling gasoline through the tank-to-pump line with the vacuum pump, I reconnected everything, and the car started running normally again.
I thought I’d fixed it, but after approximately 15 minutes of driving, the exact same thing happened. It started bogging down, sputtered, died, and wouldn’t restart.
The following day, I tried again. I added a little gasoline to the carburetor, managed to get the engine running, and it continued running on its own for about five minutes before dying again.
At this point, I’m pretty confident it’s a fuel-delivery issue, but I’m trying to figure out exactly where the problem is before throwing parts at it.
My questions:
Does this sound like a mechanical fuel pump that’s failing intermittently or losing its prime?
Could a small air leak on the suction side cause the car to run normally for 5–15 minutes before dying?
If gasoline flows freely through both the tank-to-pump line and the pump-to-carburetor line, is there anything else I should be checking?
What’s the best way to definitively test the mechanical fuel pump before replacing it?
I’m planning to get a low-pressure fuel-pressure gauge to test the pump, but I’d appreciate any other ideas or things I might be overlooking.
Thanks in advance!


r/projectcar • • 1d ago

Way too many hours later… and we’re still not driving it!

Thumbnail
gallery
74 Upvotes

r/projectcar • • 23h ago

Am I crazy for choosing a classic restomod project over a more practical modern sports car as a base for a project for a daily drive?

22 Upvotes

I’m torn between two cars and would love some advice.
I’ve found a beautiful 1970 Triumph Spitfire Mk3. It’s collector-owned, recently rebuilt, looks pristine and has a Triumph 1500 engine fitted. I absolutely love the styling.

The other option is a 2001 Mazda MX-5 NB2, with 100,000 km (62k miles) and full service history. Both cars are priced fairly similarly, with the Spitfire being slightly cheaper. The MX-5 is obviously a more modern and capable platform, but I don’t find it nearly as attractive.

I already own a Land Rover Defender 300Tdi, so this would be my second car. However, I’d still like something I can comfortably daily drive, take on long road trips and potentially take to the track on the rare occasion.

I’m planning on modifying whichever I buy. With the Spitfire, I’d consider an engine swap, suspension and brake upgrades, and other improvements over time to make it more reliable, comfortable and capable.

My head says MX-5, but my heart says Spitfire. I love the Triumph’s looks and the idea of building a classic restomod, but I’m worried about how much time, work and money it would take to make it a genuinely usable daily driver.

What would you choose?


r/projectcar • • 1d ago

Getting there 😁

Post image
96 Upvotes

r/projectcar • • 1d ago

Do I sand off the old paint or I can slap on primer and paint? Attempting to paint my car soon.

Post image
52 Upvotes

It probably sounds like a stupid question but I gotta ask since the current paint looks okay but close up it’s slowly fading away or chipped off. I wanted to try buying the equipment needed to do a paint job and before I start I was curious if I have to remove all the current paint off.


r/projectcar • • 1d ago

Still have some mechanical issues to work on but she's nice and clean!

Thumbnail
gallery
53 Upvotes

washed, clay bar, and wax. I love this yellow


r/projectcar • • 3h ago

ISO GMC Typhoon / Syclone 1987 Buick grand national / 1996 Chevrolet impala SS / F-150 lighting. Wire / Cash / Cashier Check ready! PM me.

0 Upvotes

r/projectcar • • 1d ago

Build Progress 1970 Charger getting some love…

Thumbnail
gallery
179 Upvotes

r/projectcar • • 1d ago

Car starts but dies

Post image
16 Upvotes

Hello! I’m working on my 1984 Renault Alliance project car. I bought it in non running condition. I installed a new fuel pump and filter. The car will now start and run for about 5ish seconds then dies, if I give it any throttle at all it immediately dies also won’t start if any throttle is applied. I looked at the vacuum lines, all seem to be in good shape. It has the Throttle body injection. Is there anything that stands out that I should look into? Thanks


r/projectcar • • 19h ago

Michigan Mechanic

2 Upvotes

Anyone know any good mechanics in MI? I have an early 90s Geo Tracker and it's in need of a tune up. It's got a rough idle and the whole car shakes. I'm in Oakland County. I know that these vehicles are easy to work on I just don't have the time and would like to have someone who actually is familiar with the Geo Trackers to work on it.


r/projectcar • • 2d ago

Something a little different in the garage — my turbocharged Dodge Shelby Charger

Thumbnail
gallery
984 Upvotes

Thought some of you might appreciate a look at a car you don't see very often anymore.

Here's my Dodge Shelby Charger, powered by Chrysler's turbocharged 2.2L four-cylinder.

I've always appreciated how different these cars were from the traditional American performance machines of the time. Lightweight, front-wheel drive, turbocharged, and loaded with unmistakable 1980s Shelby styling.

The black and silver exterior, Shelby graphics, rear louvers, and distinctive seats really set this one apart.

Included some pictures of the exterior, interior, and engine bay for anyone interested in these old Turbo Mopars.

Anyone else here own or work on an old Turbo Dodge? I'd love to see what you've got!

#ProjectCar #TurboDodge #ShelbyCharger #TurboMopar #ClassicMopar


r/projectcar • • 1d ago

ACC with mass backing question

Post image
9 Upvotes

Wanting to know if it’s necessary to remove this insulation before installing my new ACC carpet replacement with mass backing.


r/projectcar • • 1d ago

Troubleshooting Help Is it possible to fix this type of paint damage without a full respray?

Post image
10 Upvotes

It’s not dust, looks a lot like it tho. When the car is wet I can’t see it but after drying it comes back.


r/projectcar • • 10h ago

⚠️ OFFICIAL PRESS RELEASE: In Response to the Unwarranted Censorship & "Slop" Accusations by r/supercars Moderators

Thumbnail
gallery
0 Upvotes

From the Desk of the Chief Backyard Engineer, "realNoobNoob" Garage & Fabrication Group
For Immediate Release

It has come to our attention that our ground-breaking, 100% hand-built 1,200 HP AWD "Wedge" has been removed from r/supercars on baseless accusations of being "AI slop" and "imaginary."

While the internet’s self-appointed forensic investigators and armchair engineers are busy measuring headrest heights on their phone screens, we are actually in the shop turning wrenches.

To address the highly specific (and frankly, hilarious) concerns of one particular Reddit investigator (u/LUXOR54), we have drafted this formal engineering response:

  1. THE "HIGH-ENGINE VS. EMPTY-BAY" GEOMETRY CONTROVERSY

  2. Skeptics claimed our twin-turbocharged V8 is "sitting as high as the headrests" in the garage footage, but was "invisible" in the outdoor walking video.

Bullet The Reality of Packaging: The Twin-Turbo V8 is mid-rear mounted, nestled extremely low inside a heavily modified, custom tube-frame cradle. What you saw "sitting high" in the garage video is the colossal, custom-welded aluminum intake plenum and turbo piping which sits directly beneath the high hatchback cover.

Bullet Aero and Angle: The rear window of the wedge is deeply tinted and highly angled. When the rear hatch is closed (as seen in the outdoor walkaround video), the dark glass and natural outdoor reflections completely obscure the top of the intake. It's called optics, not AI. We don't have time to design a glass engine cover when we're trying to contain 1,200 horsepower.

2. TO THE MODERATORS AND "AI" DETECTIVES
You call it AI; we call it custom TIG welds and questionable backyard tolerances. If our panels look slightly uneven, it's because they were cut with an angle grinder, not a factory laser. That is called character, not a rendering error.
We challenge any "slop" accuser to bring a magnet, a flatbed, and a camera to our shop. Just because your hands have only ever touched a keyboard doesn't mean we can't build a 2.3-second 0-60 weapon out of sheet metal and willpower.

WHAT'S NEXT?

Since the elitists at r/supercars apparently only want to look at lease-financed Ferraris and stock Porsches, we will be taking the Wedge where it is appreciated: The drag strip and the local Cars & Coffee.

Stay skeptical, Reddit. We'll be busy doing 1,200 HP AWD launches while you guys argue about pixel counts.

- realNoobNoob OP
Lead Fabricator, "Wedge" Prototype #001

EDIT: Due to overwhelming demand from Reddit's top forensic engineers asking for our chassis schematics and suspension geometry, we have decided to open-source the original CAD blueprints. You can view the full technical specifications https://imgur.com/a/ouuAsoW