r/mechanic • • May 20 '24

General Over reacting or right to be annoyed?

Thumbnail
gallery
1 Upvotes

I recently took my car to a local shop and had a few repairs done on my new 1988 f250. They replaced the windshield washer fluid reservoir. I just noticed this is the screw they used to remount it. I have only had the truck for a few months. I had pictures of the engine bay when I bought it, and I noticed in the pictures the proper bolt is in place.

Would you find this repair acceptable or am I overreacting? I have not touched that screw, so they would also be the ones that stripped it. Thanks for the feedback.


r/mechanic • • Jul 19 '26

Question 2014 dodge charger bumper alignment help!

Thumbnail
gallery
0 Upvotes

Idk if I’m tripping or does my bumper look not aligned. If not then how can I fix it?


r/mechanic • • Mar 31 '25

Question What needs to be replaced?

2 Upvotes

To add on my last post. 2006 Chevy 2500. Installed rough country 3 inch lift, put torsion key bolt in the same amount they were, just added spacers and wheel, and it looks like the wheels are going in and out on bumps and stuff, looks very unsafe. This is how I can move it when jacked up. What needs to be replaced? I’m trying to avoid driving it to a shop as I will be putting everything in myself. Please anything helps.


r/mechanic • • Jul 15 '24

General these are the 4 best smells in the world. who agrees?

Post image
16 Upvotes

r/mechanic • • Jul 18 '25

Question Why doesn’t my ac blow cold air in my 2014 Nissan Altima

0 Upvotes

It’s been about a month already that my ac is not blowing cold air, it just blows hottish/coldish air


r/mechanic • • Jan 13 '25

Question Is my car still good to drive

Post image
0 Upvotes

I know cold weather causes tire pressure to drop at times but i can still drive this until i get them filled back up right?


r/mechanic • • Oct 16 '26

Question What’s this noise?

0 Upvotes

You may have to turn up to hear, brake shield hitting the rotor? I’m not sure at all, appreciate any help thank you. 2016 Ram 1500 5.7


r/mechanic • • Dec 12 '25

Question Rust repairs and suggestions

Thumbnail
gallery
2 Upvotes

How much of a pain in the rear can I expect for rust repairs. I plan to do it myself and just wanna know how deep of a pit I’m jumping into . Following rules my car is a 2006 tdi jetta with the 1.9l brm motor. The trunk lid is also rusted out but I’m just gonna replace that


r/mechanic • • Dec 29 '24

Question Resurfaced with an orbital sander

1 Upvotes

Is this ok to go back into my van with a new clutch 2012 cirtoren berlingo


r/mechanic • • Jun 20 '26

Question What’s it like being the Elle Woods of a mechanic shop?

0 Upvotes

Hopefully you people know who Elle Woods is. Looks like a dumb blonde but is actually smart and people kept underestimating her until she won a case. From the movie Legally Blonde.

Anyway, I’ve been thinking about quitting my 9 to 5 for a while. I used to build cars while I was in school and it was really good money for a student but it was back breaking work being on an assembly line. I do miss it from time to time but I have to keep reminding myself that my body can’t handle being on my feet 7-8 hours a day with barely any breaks. While I did love the work I can’t do it anymore. I did want to go to school for a few trade jobs like carpentry and electrician work but my parents were against it because I would never get hired because unfortunately sexism is a thing. I listened to them even though I had to pay for my own schooling. Now I’m older and I believe I can take care of myself in a sexist fucked workplace.

So I have been thinking why not learn how to be a mechanic? I’m a hard worker and I learn best while on the job instead of at school. I have asked and I apparently have to slowly buy my own tools. I’m thinking to keep people from stealing my shit I would buy anything and everything pink and/or purple.

Is it a stupid idea? And how much do apprentices get paid? I assume there is a difference between male and female pay, right?


r/mechanic • • Feb 25 '26

General Pulled the trigger on this today

Post image
81 Upvotes

Soft close drawers, USB, big as your mom.


r/mechanic • • Sep 18 '26

Rant used car dealer mechanic removed my rear converter

Post image
0 Upvotes

I am financing a 2008 honda accord that i got almost 2 years ago. November of last year i had an oil leak and exhaust leak, which the place had fixed for me. I was due for inspection in February and got that done on the 4th. 2 days after inspection, check engine light came back on and i gradually started having more issues with the exhaust. Went back to the dealer, and they “fixed” it on the 17th. I’d like to preface that i have had a check engine light on most of the time i’ve had this vehicle. All the codes have been cat/o2 sensor related. Fast forward until just recently, i began having issues yet again. Exhaust is getting louder, there’s a loud metallic buzzing only around 1500rpm and when i’m coasting. Did some looking around, and the flex pipe they had replaced was rattling a lot. I work at the part store they get most of their parts from. i was looking at the exhaust diagrams for my car, and realized that it looks completely different than what they put onto my car. I go out to my car, and what do you know, there is no rear catalytic converter. they put a 10 inch flex pipe on with a connector, and deleted the cat. I’ve had a check engine light on for the downstream o2 sensor reading low and high voltage, and it makes sense because there’s nowhere for it to go. i’m not sure what they did with it yet. Anyway, i gather up the pictures, evidence of parts they bought, and the inspection paper work and go in to talk to them. They tell me the mechanic who did the work no longer works there. They said they will get me the invoice for the work that was done, and contact me back about next steps to fix it. I told them I would rather them not do the work to it as I do not trust them. This whole situation has been so frustrating. If they do not cooperate I will end up reporting them to the attorney general.


r/mechanic • • Aug 22 '26

Question What do yall recommend? I can’t get this top nut off. Just keeps spinning the damper. BCracing coils for WRX. I’m replacing the damper. 🙏🙏

Post image
0 Upvotes

r/mechanic • • Dec 26 '24

Question What’s wrong with the car?

Post image
0 Upvotes

My girlfriend just texted me saying that her shift stick on her 2018 Civic feels loose. She says she shifted and it “felt smoother than usual.” And I don’t know if this has anything to do with it but her reverse camera stopped working properly?


r/mechanic • • Feb 17 '26

Question 2009 IS350 won’t start not even accessories (HELP!)

0 Upvotes

So i drove my car to work and on my break i go into my car and i try to press the push to start button and i don’t get anything, i try again and again checked battery cables reconnected it tried to jump it and nothing. Called triple A after work and they tested the battery it was at 90% health and charge and a jump didn’t do anything, and the alternator was replaced 2 months ago. Car won’t even make a noise or a peep or a click, my headlights turn on and they’re bright, the tail lights work too and the lights inside the car are perfectly fine, the only accessory on the dash is it saying my moonroof is open, and it saying my door is open. Car unlocks and locks.

Anyone know what i should do or how to fix it? It’s not the battery


r/mechanic • • Mar 05 '26

Question Should there be a gap between my break pad and rotor??

Post image
0 Upvotes

2008 Ford Escape. I


r/mechanic • • 23d ago

Question What could be the issue?

32 Upvotes

Wheel bearing or toe rod?
Rear left tire

C4 corvette 1991 manual


r/mechanic • • Feb 06 '25

Question Are these snow chains the wrong size ?

Post image
35 Upvotes

Trying to get some input— are these tire snow chains the wrong size? Or, did I put them on wrong? Thanks


r/mechanic • • Feb 13 '26

Question Why won’t my truck jack up?

Thumbnail
gallery
0 Upvotes

I have jacked up my truck a few times before and it seemed perfectly fine but now for some reason when I put a jack stand under it the trucks wheels go low and touch the ground and it doesn’t matter how high I go it does it every time? Am I doing something wrong help me. And when I try to slide jack stands under one is higher than the other? Is my trucks suspension done?


r/mechanic • • Oct 21 '24

Rant Best way to explain this to my mother?

Thumbnail
gallery
69 Upvotes

I was driving on the highway when one of the trucks with big flashing arrow was parked in the fast lane and I couldn’t slow down so I had slight impact with the back of the truck. I know I must be blind to not have seen it in time to break. He didn’t have any damage so we both walked away without filing a police report or insurance claim. Is there a better story that I can tell her than rear ending a large truck with a large flashing arrow on the back? Maybe hit a gate while parking or hit a pole thinking the car was in reverse? Any advice will be appreciated!


r/mechanic • • Oct 12 '24

Question Help with these stains please

Thumbnail
gallery
0 Upvotes

Hi! I have these 2 stains on my windshield that won't go out. I've already tried to wiped from in and outside but they're still there. Does anybody know what can I do to make them go away? Thank you! :)

Audi A1 sport back?


r/mechanic • • 3d ago

Question Help Me Solve This No-Start Mystery

Thumbnail
gallery
0 Upvotes

Update:

Didn’t know there were so many negative nancies in the mechanic subreddit.

I fixed the car it runs good👍

The insulation for the TPS wiring was falling apart so they got some TLC (Thrown in the trash and replaced)

It was right under my nose (Page 3 “P0123 & P2135” theory)

I know it was getting air since it ran on starting fluid.

The fuel system was working but to rule out the pump entirely I bought a new one. The old one had cracks on the housing anyway.

The fuel rail received pressurized fuel but something was cutting it off. I checked the manual, and I found that pushing the pedal to the floor during start up causes the engine to cut off the fuel injection to clear flooded cylinders (Which probably caused P0123) Meaning the sensor wire is probably reading high voltage thinking the pedal is all the way down. I confirmed this with a multimeter, it was one of the first things I did. In the manual for the 2010 Pontiac Vibe I think it’s in the starting section 8-16.

Anyhow I just want to say thanks to everyone who said I don’t know what I’m doing instead of saying something helpful, you guys were so funny.


r/mechanic • • Oct 16 '25

Question Weird light came on

Post image
55 Upvotes

2004 Lexus es330, the check engine, abs, brake, and maintenance light are always on but the one with the car and rear beams I think? Does anyone know what it is?


r/mechanic • • Jun 10 '25

General When your “20 minute job”…

3 Upvotes

…turns into thundercunting your wrench into the garage door. Gobbless