r/lurebuilding • • Jan 02 '20

How to Make Your Own Lures: A Guide series

101 Upvotes

1. What kind of lures can I make?

  • Crankbaits (Lipped and Lipless), Jerkbaits (Lipped and Lipless), Swimbaits, Poppers, Stickbaits, and other topwater lures are all possible, with new lures being invented all the time! Below is an info graphic with a few of the most popular types of fishing lures, but there are many more!

2. What do I need to get started making hard body lures?

  • Lure making is not as complicated as it may seem. Yes, power tools such as drills, dremels, lathes and sanding machines all help, but none are necessary. To start all you need is:

  • Wood, to carve into the body.

  • Tools (at the very least a knife to carve, a small saw, and a drill are all very helpful)

  • Sandpaper to finish the bait off smoothly

  • Terminal tackle, including hooks and split rings

  • Screw eyes or a through-wire (a single wire going through the entire bait that serves as your hook eyes and line tie.

  • Weights so your bait sinks, in the form of either split shot, glued into the body, or lead, poured into a cavity.

  • glue/sealant, epoxy, and paint

  • OPTIONAL: Lip (for crankbaits) Rattles, details such as foil, and power tools, and an airbrush for more smooth

3. What do I need to get started making soft plastics?

  • A mold, which can be bought, or made from silicon.

  • Plastic resin (plastisol)

  • Dye to give color to the lure

  • OPTIONAL: Glitter, multiple colors for a more detailed bait

4. What wood should I use?

  • Popular lure making timbers include balsa, basswood, cedar, cypress knees, jelutong, beech and some types of pine. But there are thousands of other options. Look for something easy to carve, lightweight and resistant to denting. It’s easier to get all your components aligned properly if you start with straight, square blanks.

5. What paints should I use?

  • For brushing on paint, a wide variety of artist acrylics and poster paints will work. Just make sure the paint and clear coat will not interfere.

  • For airbrushing, water-based acrylics are the favorite, due to their ability to spray evenly and produce a good coat while remaining non-toxic, and non-flammable.

6. How do I seal my wood lure?

  • Wood is like a sponge, it soaks up water. Once in, water works its way through the wood by capillary action until the wood is waterlogged. This kills action, weakens glue and is the most common cause of paint failure.

  • Super Glue can be used, where the glue is applied over the entire body, left to soak into the wood, and then the bait is sanded smooth.

  • Epoxies are two part synthetic resins that cure hard when mixed. There are some that are designed for penetrating and hardening wood. One example is Envirotex Lite (aka “Etex”). Etex is also great for clear coating painted lure bodies and makes a very strong adhesive.

7. Where can I buy lure parts?

8. What epoxy should I use?

  • Some use prefer to clear coat them with a two part epoxy. Others prefer to use a two pack automotive polyurethane over airbrush acrylics. And still others dip their lures in moisture cure polyurethane.

Below are some some more sources for learning how to build lures, additionally, guides from some of this subs best lure mentors are going to be rolling out very shortly.

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

This stickied post will be used to compile all guides made by our "Lure Mentors." Below are links to each guide, complete with pictures and detailed descriptions for each step. If you would like to become a Lure Mentor, and create guides for this sub Please PM me ( u/jspencer501 ) for more details, you get a cool flair!

Guide 1 - Lipless Crankbait By u/zingerbobingerGuide 2 - Lure made of Paper By u/SolarBaits

More guides will be coming out in the weeks to come! please let me know any comments or concerns.


r/lurebuilding • • 3h ago

Swimbait Does anyone have some unofficial mods/tunes for the tinyklash or k9?

Thumbnail reddit.com
2 Upvotes

I have been experimenting with different mods for my tinyklash for a long time now, would love to know some more!


r/lurebuilding • • 3h ago

Question Best UV paint for lures

1 Upvotes

What the brightest and long lasting uv paint y’all have used and recommend when painting your lures?


r/lurebuilding • • 1d ago

Jig Salve ragazzi

2 Upvotes

Sto facendo degli stampi per esche da pesca, per risparmiare gomma siliconica HT è possibile fare una prima fase in gomma siliconica fino a coprire l’esca e poi dopo mettere del gesso a creare spessore? Grazie


r/lurebuilding • • 2d ago

Crankbait Lil nuggets to go with the big nugget.

Thumbnail
gallery
47 Upvotes

r/lurebuilding • • 1d ago

Question Lure making

5 Upvotes

I am trying to figure out what materials are needed for a larger kind of lure. I saw my father in law watching a YouTube video on lure making. I’m not sure who he was watching but the lure being made was as big as a man’s hand, it looked like it was a lot of blue strings (I want to say as thick as half a box of spaghetti noodles) and he was wrapping the top. I asked him what kind of fish that lure is good for fishing and don’t remember his answer. My father in law goes fishing in the ocean, he usually brings home dolphins and rosys (that I have seen). I am trying to figure out what to get to help with the process, I’ve been racking my brain trying to figure out what to get him for Christmas so I can’t ask him any questions.


r/lurebuilding • • 2d ago

Swimbait This is still really hard lol

Post image
24 Upvotes

Feeling better about things. But...Holy crap there is alot to learn. About 3 months into this journey.


r/lurebuilding • • 2d ago

Glidebait Just cut and carved this 5” trout glidebait. Thoughts so far?

Post image
10 Upvotes

r/lurebuilding • • 3d ago

Spinner A Dark Inline Spinner

Post image
28 Upvotes

Black french spinner with holographic decals, hematite bead body with brass bearings, dressed hook with rooster tail flashabou.


r/lurebuilding • • 3d ago

Question Has anybody tried using these 3d printed lizards as a Lure?

Post image
10 Upvotes

I get some version of these in gift bags pretty regularly.

Instead of throwing them away I'm wondering if they would be any good for a lure.

The flexibility should make for good action, and the concave pieces should make a good amount of noise as well.

Obviously I would need to attach the hook to the "head" so that it doesnt effect movement but is also strong enough .


r/lurebuilding • • 2d ago

Question Do blades of the same type have standardized sizing?

2 Upvotes

I'm looking to order some inline spinner blades, and I'm confused about the sizing.

I'm comparing sizing charts on Janns Netcraft to the sizing chart on luremaking.com.

The inline spinner blade size 1 looks larger on Janns than on luremaking. Luremaking states the dimensions (3/4" length), but Janns doesn't state their dimensions.

If anyone has experience with these, I'd love to hear. For a point of reference, I normally use Mepps size 1 spinners, and Panther Martin size 1 spinners. Panther Martins run a bit smaller.


r/lurebuilding • • 3d ago

Glidebait My first attempt

Post image
30 Upvotes

I've started getting into making my own fishing lures. If you have any tips, please share them.


r/lurebuilding • • 3d ago

Spoon Spoon outline and cup depth, followed by a steady retrieve and fluttering fall

0 Upvotes

I'm the developer of MakeMyLure, the software in this clip. I work on it in my spare time as a personal hobby. It isn't how I make my living, and I'm not trying to make a profit.

Daily lure series, episode 4 of 9.

The design section changes the spoon outline and cup depth, then selects paint. The swim examples show a slow steady retrieve and stop-and-go, including the model fluttering downward during the pause.

The clips are real-time software simulations of the displayed setup. They provide a way to inspect the design before a prototype, while material selection, hardware behavior and the final action need physical checks and real-water testing.

The workbench is now free after registration, with no subscription fees. I pay the server, storage and AI-token costs myself. The old trial wording in this recording is no longer current. Handmade products and custom builds are priced separately.

Concrete suggestions, broken examples and honest criticism are welcome. Handmade lure makers are also welcome to share or list their own work in the forum, including links to their own shops: https://makemylure.com/forum


r/lurebuilding • • 4d ago

Swimbait Simple hardhead rig for large plastics and a spintail mouse.

Thumbnail
gallery
7 Upvotes

r/lurebuilding • • 5d ago

Jerkbait BFS, trout and homemade jerkbaits

Thumbnail gallery
15 Upvotes

r/lurebuilding • • 5d ago

Swimbait Herring and Mullet for Australian Saltwater

Thumbnail
gallery
30 Upvotes

Sending these 2 to a friend in Australia to raffle off. They requested a herring and mullet pattern for targeting saltwater predators. I’m still not as great as I would like to be with airbrushing, but the build quality and hardware will be good to go. These are hand carved basswood, roughly 10.5” and 4.5 ounces…tuned to sink slow/suspend as requested.


r/lurebuilding • • 5d ago

Crankbait Nugget is finished

Thumbnail
gallery
120 Upvotes

r/lurebuilding • • 6d ago

Crankbait First lure

Post image
39 Upvotes

Was bored over the weekend and started carving a little scrap of poplar. I don’t have any power tools so it was a tedious process and fun learning experience. I am scared to fish with it as I will probably get snagged immediately.…but I will definitely make more. I may need to buy some air brush equipment for the future.

Any tips or suggestions are appreciated thanks.


r/lurebuilding • • 5d ago

Spinner Too bad you can’t give it two flairs for soft plastic and spinner bait

Thumbnail
youtube.com
2 Upvotes

The perfect imitation to the dragonfly


r/lurebuilding • • 6d ago

Jerkbait Minnow buoyancy during the pause, plus three simulated retrieve patterns

0 Upvotes

I'm the developer of MakeMyLure, the software shown here. This is a demo of my own product and episode 1 of 9 in a daily lure series.

The minnow is ballasted three ways for the floating, suspending and sinking lanes. Each uses a stop-and-go retrieve, with that comparison played at 0.85×. The later examples show steady retrieve, twitch-and-pause and short twitches.

The clip also walks through body shape, bill angle and paint. These are software simulations of the shown setups. Physical prototypes need assembly checks, a buoyancy check and real-water testing.


r/lurebuilding • • 7d ago

Spinner DIY lures

Thumbnail reddit.com
2 Upvotes

r/lurebuilding • • 8d ago

Crankbait i didn’t MAKE the lure, but i did give it new paint. i had found a vintage cotten cordell while lure hunting in trees and the OG paint was tacky/sticky and gross. i never change lures that i find but this one wasn’t fishable in the condition lol.

Post image
15 Upvotes

r/lurebuilding • • 7d ago

Crankbait From a digital lure design to a hand-carved wooden lure

0 Upvotes

I’m the developer of MakeMyLure, the design tool shown in this clip. This is a demo of my own product.

The clip runs through shaping, paint layers and a simulated swim. A lure maker carved the lure in the photo entirely by hand from wood, working from the design and paint layers. The swim is a software simulation of the design. The wooden lure still needs its own water test.

For builders who hand-carve crankbaits, what do you decide first before cutting the wood: the body profile, the bill slot angle, or the ballast placement?


r/lurebuilding • • 8d ago

Glidebait which orientation is best ?

Thumbnail
gallery
11 Upvotes

First time hand carving a glide . Was aiming for a s waver sort of design but after I got the rough body finished I realized it could possibly work the other direction and sort of looks like a chad shad . What do you guys think?