r/consolerepair • u/entropicanonimity • 14m ago
[PS5] Screw these zif connectors
Also your PSA to not blindly trust AI for help. It suggested me to pull the relese bar the opposite direction.
r/consolerepair • u/entropicanonimity • 14m ago
Also your PSA to not blindly trust AI for help. It suggested me to pull the relese bar the opposite direction.
r/consolerepair • u/Horror-Ad5783 • 2h ago
Hello, I have a very specific issue. The touchpad on my PS5 controller is not clicking and gets stuck. The touch is working fine, just the click. I have tried resetting the controller, it did not reset completely no matter what way I tried. I have cleaned the sides, there doesn’t seem to be a blockage. Please help.
r/consolerepair • u/washunter • 2h ago
This was my first soldering project I've attempted, so the board is a little mangled and I'm sure my soldering job isn't great lol but I'm kinda stuck with this problem. Does anyone know what might be the issue?
r/consolerepair • u/Negative-Price7051 • 2h ago
Quisiera saber si alguien sabe cual es el capacitor q falta en la foto? Es de una ps5 fat cfi1016a , placa base edm010 side b , detras del chip ssd [CXD90062GG] , creo que es un smd 402 . Es de una ps5 que compre averiada y ya faltaba . Gracias de antemano a toda la comunidad
r/consolerepair • u/AyeJayeB • 3h ago
Does someone experienced the same issue like this? My left joycon battery indicator constantly switches from charged to charging. Is there a fix for this?
r/consolerepair • u/Arcangel_xxx • 3h ago
Hi everyone,
I’m currently troubleshooting a PS5 Digital Edition (CFI-1015B) and would appreciate some advice from anyone experienced with PS5 motherboard-level repairs.
Symptoms:
● The console beeps when pressing the power button.
● Sometimes, on the second attempt, the blue light comes on for approximately 1–2 seconds and then the console shuts off.
● The fan does not appear to start.
● The issue appeared after a crash while launching a game.
Previous history:
The console has previously undergone a deep cleaning, including work around the APU area, where some oxidation was noticed.
What I’ve checked so far:
I’ve started inspecting capacitors around the APU and other motherboard areas.
I found several capacitors marked 560. I’ve checked six similar capacitors, and none showed an obvious short circuit. Their readings were approximately 0.091 on my multimeter during testing.
I haven’t replaced any capacitors yet because I want to understand the fault before removing components unnecessarily.
My questions:
Has anyone experienced this exact startup behavior caused by faulty capacitors?
Have you successfully repaired a PS5 with similar symptoms by replacing capacitors around the APU?
Are there particular capacitor groups or power rails I should investigate first?
Would you recommend checking specific power rails or enable signals before attempting capacitor replacement?
Could this behavior point to a power sequencing issue rather than a faulty capacitor?
I have a Fluke multimeter, adjustable DC power supply, hot-air rework station, soldering station, and microscope, so I can perform board-level diagnostics and component replacement.
I’m not looking for random part replacement. I’d really like to hear from someone who has actually diagnosed and repaired this type of PS5 motherboard fault.
Any suggestions, previous experiences, or repair references would be greatly appreciated.
Thanks!
r/consolerepair • u/Fickle-Position-3575 • 4h ago
Hey guys, i have a PS4 CUH-1116A that is giving me a tripple beep when pressing the eject button but nothing happens when pressing the power button. Just wanted to know if someone might have a clue where to look before i waste hours trying to fault find it.
It's not the PSU (tested with a known good).
Thanks in advance.
r/consolerepair • u/Cube_N00b • 4h ago
Does anyone have the value for C201? I don't think this board is in the schematics for the Series X.
The capacitor was shorted to ground and cracked, causing no power on the console.
r/consolerepair • u/socom_II • 5h ago
So I'm pretty confident the wireless receiver is drawing too much on the +3.3v line causing the video to drop occasionally. I think it only happens when I have the adapter on rumble pack mode. Might be a stupid question but will adding another capacitor to the 3.3 line or large cap to an existing pad reduces this? The system and PSU are recapped(console5 kit). It is modded with a retro gem HDMI kit without the clock mod. The firmware for the kit/receiver are updated. Thanks for any help or feedback!
r/consolerepair • u/Mike4046 • 5h ago
I’ve got this Nintendo switch 1 in for repair. Customers said it wasn’t charging.
I plugged it in and it jumps to 450mA but doesn’t turn on or show the battery symbol.
I’ve checked for shorts around M92T36 & P13USB but couldn’t find any.
The only thing I did find was a shorted cap next to MAX77620A which turned out to be a short in the LCD connector which I think I caused when either removing the motherboard or trying to put the motherboard back in. Either way I fixed that but not sure why it’s not turning on. Anyone have any suggestions?
r/consolerepair • u/MembershipOk9657 • 6h ago
Got this from someone who tried to swap the USB C port with a hardware store heat gun, told them I'd try to save it. Half a day of work later it docks and charges fine again. Still not quite happy with all of the pads, but I learnt a lot.
r/consolerepair • u/crud3 • 8h ago
probably hasn't run since 2015 but mint shape... needs lube or something? Or?
r/consolerepair • u/snepaibinladen • 9h ago
hey my psv 2000 is dead and I would like to give a little context how it really happend:
so I took my vita out after 2 years and when charged it was charging and turned on suprisingly and seemed fine ( modded vita).
But then when I try to play games it showed me several data corruption errors which i thought would simply due to the outdated plugins so I formatted the whole thing and re modded it. Games worked fine but then it had wierd battery behaviour like it would take an hour to charge by 1% or 2.
Then the actual situation arrives, when i turned on the device it suddenly showed me a an error **do not remove your memory card while system is on ( i didn't) and it froze there forever until i force shut it down, since then it wouldn't charge nor turn on** .
I gave it to repair and the technicians quoted the motherboard is corroded and cannot be fixed. But i feel they weren't ready to experiment on this niche console.
What do you guys think of this? I'm thinking to diagnose and fix this on my own, I've got some stuff like multimeter lying around so I thought I'd ask somone here to rest stuffs, how do I begin with?
Note: I've tried measuring the battery it shows 3.7V i guess
r/consolerepair • u/Toscotitto • 13h ago
Hello,
Managed to fix several things on a PS5 edm-010 but now I got some strange faults.
Beep on and beep off.
According to UART following:
80810001SeverePowerSequence - Power Sequence Error - General Power Failure (Peripheral, GDDR6, APU, Data Line Short)
808B0092HighNot found in list. Report Findings.
The console draws 245mA at 12V at start and goes down to 5mA. When powered on, the console draws 245mA for about 5-10s and down to 5mA again.
What I've noticed on the console:
I receive correct voltages around Dialog chip.
I receive 0 voltage around the hdmi retimer.
I get the stand by voltages (5V and 3.3V) backside of the hdmi retimer but no 3.3V power on voltage.
I get some kind of short (I think?) on the GDDR6 power regulator vias, (0.38V diode / 28.4ohms).
According to donor boards (Have removed a couple of chips so can't be sure of the readings) I should get around .145V diode / 100ohms.
No short on wifi chip
No short on southbridge
No short on SSD
All fuses are fine
I've replaced following:
SSD-controller
DDR4
Southbridge
Several of components like ex. capacitors, coils and mosfets from the GDDR6 power regulator.
Dialog chip for SSD voltage regulator.
Any suggestions on what to look at next?
r/consolerepair • u/Romas002 • 13h ago
Hi all i have short at sic655a output. Maybe sameone knows where it goes? I have dismantled all components around it but still short. Can it be shorted APU?
r/consolerepair • u/SmokeOdd775 • 15h ago
My cat knocked soda onto my switch (it's a lite)by accident, and my left joystick isnt working well (video) but my husband ordered a repair kit for it...his friend is gonna try and fix it. Will it save it? Everything else looks fine..
r/consolerepair • u/Pomelodude • 16h ago
To go off my original post I found the issue. How do I fix this?
r/consolerepair • u/Csnj2 • 16h ago
I was trying to change the Liquid Metal on my ps5 and when opening it I stripped one of screws on the heatsink bracket.It’s the one that is like an X and now I’m struggling to find a replacement does anyone know what I can do or find a replacement for the screws.I looked on eBay but can really find anything and was wondering if maybe I can use the screws from another system like a ps4 or something like that.
r/consolerepair • u/TurtleSatan • 19h ago
Had my PS for 4 years. Recently started shutting down randomly before not switching on at all. I had it cleaned. Worked for a day and then the same issue.
Sent it to a guy and it seems to me like I just need to replace the thermal paste judging by the image but he's saying it can't be fixed.
Please see images and advise.
r/consolerepair • u/Hairy-Pomegranate897 • 20h ago
I was moving it around to a different spot, just trying to get it into a more accessible spot considering the controllers.
When I plugged it in though, everything was okay until about a minute later when it started smoking and gurgling.
I think it’s only the big capacitor that exploded, I tested the resistors and they were okay but I haven’t got much further yet.
Also, the cord I was using was from EBay, which normally is fine. It had all the correct ratings so I don’t actually know what caused this.
Anyway, I do have the supplies to repair it, I’m just not too experienced. Does anyone have suggestions for either a new power board or just a new capacitor? Or did something else most likely get damaged beyond repair?
r/consolerepair • u/RetroRenew4l • 20h ago
While I'm fairly experienced in reballing large processors such as GPUs, small ICs such as for phones with 0.2mm or similar sized balls are a bit of a hassle.
Keeping the stencil in place solely freehand, and using solder paste that is largely too wet (too much flux).
Anyone have recommendations on a chip holder for small chips of various size? And a solder paste that comes a bit drier from the factory?
Cheers
r/consolerepair • u/maxiewawa • 20h ago
This component has come off a new 3ds LL. I'm not sure what it is, it has Js written on it. I'm not sure how to test it (it might be damaged). It has a white bar on it so it only goes around one way. The pads it are connected to aren't connected to each other.
I'm not sure if it's relevant, but the blue light is coming on, but the console isn't starting up. Blank screen.
What might it be?
r/consolerepair • u/More-Pollution8187 • 20h ago
I recently purchased an NES - 001. Originally it would turn on and the intro screen would show but the graphics were bad and I couldn’t get past the screen (also no sound but I think that’s a different issue.
I followed a YouTube video and disassemble, cleaned and reassembled the console. I noticed three of the pins are darker than the others and they correspond to an area of the board that had some dark stuff on it. I tried to get it off but the pictures are the best I could do.
after the cleaning. I can get the game to run but the graphics are still bad and I think this is the issue. I know I can get new connector pins but what can I do about the board? Anyyhing? TIA
r/consolerepair • u/Okas43 • 20h ago
Hi all, I repair consoles for a living, and while diagnosing a Steam Deck board I found that the EC prints a pretty detailed boot log over UART. Reading it raw is painful, so I wrote a small Windows tool that decodes it live.
**What it does**
- Reads the EC log from any USB-UART adapter (or opens a saved .txt)
- Decodes the power sequence: G3 → S5 → S3 → S0, RSMRST, PLTRST
- Decodes BIOS POST codes (Insyde H2O + AMD AGESA ranges)
- Tracks 20 boot stages with timing and deviation from a known-good board
- Colour-coded: green = OK, yellow = something not connected (battery, display, SSD, controller board), red = error or hang
- If the board hangs, it shows the step it stopped at and what the EC is probably waiting for
- Built-in UART pinout window with board photos
- UI in English, Ukrainian, Russian
**Hookup**
UART RX on the board → adapter RX, GND → GND, leave adapter TX unconnected. 3.3 V adapter, 115200 8N1. Start capturing first, then plug in the battery or charger.
**Some things I learned from the logs**
- The power sequencer timing is identical to the millisecond across every configuration I tried. Missing parts only change what happens after it.
- After S0 there's roughly 18 seconds of PSP/memory training before the first BIOS codes. A board that looks dead for those 18 s may be fine.
- No SSD → BIOS ends on "no boot device"; no display → panel ID reads as not connected; no controller board → the USB stage never shows up. So you can tell what's missing without opening anything else.
**Download / source**
https://github.com/Olarkal/Steam-Deck-UART-Analizer
Free, open source (GPL-3.0). The repo also has sample logs from 6 configurations, power sequence tables and timing diagrams.
**Limitations**
Tuned for the OLED (EC ITE IT81302). The LCD model uses a different EC, so its log may differ. AMD POST code meanings come from public AGESA tables, and a few may not match Van Gogh exactly.
If you have a UART log from an LCD board or a faulty board, I'd really appreciate it. That's how the decoding gets better.