r/autoelectrical • • Nov 25 '25

Could leaving a frayed phone charging wire plugged in overnight drain a car battery? 2021 Honda Pilot. Dead battery 3 times in last 6 months. Once first thing in the morning, and twice after parked for 3-4 hours.

Post image
0 Upvotes

r/autoelectrical • • Jul 19 '25

Starter solenoid as a battery cutoff?

0 Upvotes

I have an old vehicle I don't drive often, but when I do, occasionally find the battery dead.

I would like to automate a battery cutoff switch.

My thinking is that I have 2 relays, one powered by the ignition, and one by battery. The battery relay would actually be a solenoid so it can handle starting current. The ignition relay would be to hold the solenoid when the ignition is on.

So in the jeep, I'd have a pushbutton that engages the solenoid. When the button is held, it connects the battery to the vehicle normally. If held while the ignition is on, the ignition relay then powers the solenoid, so releasing the button then just drops the battery power to the solenoid, but it stays on because the ignition relay is holding it.

So the question I then have is, can the solenoid handle continuous duty? It would have the high current during startup, but then only charging current after that. So I'm more curious about the coil being on the whole time, not the contacts.

The ignition-powered relay's contacts would take 12v from the solenoid output contact and route it to the solenoids coil to hold it on, so there's no chance of backfeeding the ignition power circuits with battery power.

Edit: although I said "starter solenoid" in the title as a habitual moniker, I deliberately said "solenoid" without "starter" in this post, as I was hoping people would offer suggestions on solenoids that would serve the purpose, or alternatives...and they have, so thanks much. This theoretical circuit has nothing paeticular to do with the starter, or any specific vehicle model. As for the parasitic draw, it's not severe enough that's there's a malfunction to correct, just a just a nuisance. A battery disco is not actually that terrible a thing. Also removed my job, as it triggered someone and isn't relevant, other than that I was adapting an old general electronics concept to an automotive application.


r/autoelectrical • • Jul 01 '25

Mechanic charged us $3375?

0 Upvotes

Our mechanic has fitted our solar stuff for our Toyota commuter van. Mind you we provided all the solar gear (battery, solar panels, charge controller, battery monitor, inverter, lights, fridge). He also removed an aircon unit that was at the back of the drivers cab. He has fitted solar gear in a hiace van for our friend for a total of $650 including labour and parts cost. He’s charging us $3375? From the start he’s been all “I’m really looking after you guys” and “I’m taking a loss on this, this is a bargain”. He is saying he’s dropped his hourly rate from $165 to $142.50 and that’s “cause he likes us”. Hes saying he’s only charging us for 2.5 days of solid work but he actually had to shut shop for a week to get this done? He wired the parts together, put in some switches/usb ports, and run some wires through the roof for the solar panels. It also seems an expensive charge when the work he did didnt look professional, there’s permanent marker on our cabinets and random holes in our cupboards. Seems like bullshjt to me but I almost want to be wrong because he seemed like such a decent guy up until now. Is this a fair price?


r/autoelectrical • • Jul 23 '26

Hi, can someone please explain what the resistance is on the DMM and why ?

Post image
1 Upvotes

Sorry I’m bad at electrical but I am trying to learn


r/autoelectrical • • Nov 14 '25

Amazon in line breaker, safe/reliable to use?

Post image
5 Upvotes

I'm setting up a 6 way fuse block in my car, I was wondering if the amazon branded in-line breakers were safe and reliable? Or should I just go for a in-line AGU fuse instead?

This is the one I was looking at, but they're all similar anyway. https://www.amazon.com.au/M1A2-Circuit-Breaker-Waterproof-Resettable/

I had a look at a few automotive stores near me (Autobarn, supercheap auto) and to be honest they look to be identical to the ones sold on amazon, just a different 'brand'.

Has anyone used then with them and have experienced them actually tripping?

Thanks all!

EDIT: For those who are still commenting, I've ended up setting a fused oned instead, just some piece of mind knowing I'm not relying on a cheap breaker that may or may not fail.


r/autoelectrical • • Mar 09 '26

Fuses, why so many different physical sizes, and why can't people use the same terminology?

Thumbnail
gallery
1 Upvotes

Following on from this post, I ordered a fuse extender thing. I'm not going to use a switch, just fit this with the fuse part more accessible and I'll pull the fuse as required (It happens about once per month.) First one I bought was the wrong size, that's on me, I ordered the wrong one. Reordered the right one and I either got it wrong again or they sent the wrong thing. I ordered Small, looks like they sent Mini.

So I've put a zip tie on the fuse for now, quicker to identify and easier to pull.


r/autoelectrical • • Aug 07 '25

Door locking issue 2002 Toyota Corolla ascent recently bought

0 Upvotes

r/autoelectrical • • Nov 16 '25

Crank no start, possibly fuel pump. Having trouble reading service manual.

0 Upvotes

Hello, (from Australia)

(car details: 2003 Nissan Pulsar, Auto, sedan, QG18DE)

Context: So basically, car was parked for a month+, now it just cranks, no-start. Suspect fuel pump, but testing needed. Check fuse, looks/tested OK. No fuel-pressure gauge, so removed fuel line. Cranked car, no fuel coming out (has fuel in tank).

Looked in a Haynes repair manual, can't find ANYTHING on the fuel pump relay. Found a Factory Service Manual (for a euro version of car), found an image of where the relay would be, that's it, nothing more :/.

Looked in car, found two identical relays -.-...

Followed testing procedure for the relay testing. Both 'click' when supplying 12v to pins 1 & 2. Both have continuity between pins 3 & 5 when powered.

No current supply, no continuity between pins 3 & 5

NOTE: No pin 4 on these relays.

NOTE: I did a continuity test between pins 1 & 2, I didn't get continuity, I got a reading 124.3 for both relays. Why was there no audible beep? Aren't pins 1 & 2 connected via a wire-coil?

Question. The above image shows a test for the fuel pump. Is it saying to probe the connector on the harness, or the connector on the fuel pump housing? I only just realised this as I write this post. I think I probed the harness & got 1ohm

Question: I read it's better to supply a load to the 12v line when testing, to see if the relay or other, is working correctly. Is this true, & if so, what load do I use? Just a test-light probe? or other 12v light?

I re-installed the relays & used my multi-meter to check voltage going through the harness to the connector. It's spikes for half a second then trickles back to 0v. Is this too quick? (see video link below)

Note: In video, ignition remains 'ON' until voltage goes back to 0v, then I turn 'OFF'. Should voltage remain on 12v +/- while in the 'ON' position?

https://youtube.com/shorts/4o12w-RXPGo?feature=share

I've been reading the 'factory service manual', but the wiring diagrams are doing my head in. I'm trying to figure out which relay is for the fuel pump, & what the other relay is for.
I found under 'Electrical (EL)' in the manual, a diagram of 'Body harness', & fuel pump wiring diagram. The fuel pump wiring says it's relay connector (B5). The body harness diagram shows (B5) connector as one relay, & the other it says "(B6) or (B7)".
This is where I'm stuck. I don't know where to find a list of connectors (B6) for example, & what they are for. I'm looking through wiring diagrams, trying to find (B6) or (B7), but I can't. I suspect it's my lack of understanding of Automotive electrical diagram reading, I don't know where to look :/. Any clues?

Are there any other tests I should be doing?

terribly sorry for the long post. I wanted to give as much information as I could. Much appreciate any assistance though. :)

Regards,


r/autoelectrical • • Jul 09 '25

Battery isolator switch. Will it work if installed on the negative terminal?

0 Upvotes

I have car (2004) that sits for weeks at a time, I have to disconnect the battery to prevent flattening it.

Was thinking of installing a battery isolator switch on the negative side, as the positive has a bunch of cables to deal with, whereas the neg, only has the one, so an easier install.

I suppose the question is, will isolating the negative stop that low current draw, from the various modules that continue to draw current even when the car is off?


r/autoelectrical • • Jun 13 '26

How to actually find a parasitic battery draw on GMT400/GMT800/GMT900/K2XX trucks (multimeter + fuse-pulling method)

Post image
0 Upvotes

r/autoelectrical • • Aug 24 '25

Best, weather resistant way to tap into a 10ga wire?

0 Upvotes

I'm looking for ideas on a good, waterproof way to tap into a wire.

I'm planning to tap into the 10ga 12v hot wire going to my trailer harness for providing 12v power to the truck bed, but want to do this in a way that won't introduce corrosion as it is in an area exposed to a lot of moisture and water. Obviously t-taps are out for that reason.

I've thinking maybe either thick 3:1 adhesive lined heat shrink tubing or making a custom 3d printed mold for encapsulating the splice in hot glue.


r/autoelectrical • • Dec 30 '25

Did I just install a faulty new alternator?

0 Upvotes

Just replaced my old alternator (13.04V output) with a new OEX 130A alternator, but it's only putting out 12.99V!!! Cross-checked my meters against my other ute (14.05V) so they seem honest. Any advice?

Edit: 2010 Toyota Hilux


r/autoelectrical • • Jul 15 '24

Can this be fixed?

0 Upvotes

One of these broken pins is a ground. Still have the pin that broke off. What are my options? I'm calling around locally to see if someone could repair, but not having any luck so far.

Could I try to find someone to solder it back on? What type of shop might I call? Or are there any tricks I could try myself to complete the ground?


r/autoelectrical • • Aug 23 '24

remote starter battery drain

0 Upvotes

disclaimer: I'm not an electrician and don't know the lingo; I'll share what I now with the words that I have

I have a 2009 Honda CR-V EXL 4WD. I got it in the spring of 2024 and ever since if it sits for too long, the battery slowly drains. As a temporary fix, I got a Hulkman portable jumpstarter. I will need to get a new battery now however, I believe the drain is coming from the third-party remote starter (it's called autostart.ca). I would prefer to do something about the drain before I get a new battery.

A friend who knows much about cars suggested getting a kill switch for the battery, like this: tiny.cc/killswitchh

Option 1: install kill switch

Option 2: remove auto starter

What I'm wondering is, if I install a kill switch, is that not just another third party item that can eventually compromise the battery life?


r/autoelectrical • • Jul 06 '24

Light bar

Post image
0 Upvotes

So I bought a stedi light bar (similar to the one pictured) and I have had someone proceed to tell me that I will not be able to run it on my 1992 Nissan safari 24volt because the alternator output is 35 amps. I previously had the original spot lights on which are not led so I would have thought that this led light bar would draw less power. Just thought I would ask before I use it and end up draining both of my battery’s


r/autoelectrical • • Nov 01 '23

How does the Lamborghini Gallardo ECU detect which gear shift paddle has been pulled when it only has two wires in the connector?

Post image
0 Upvotes

r/autoelectrical • • Jan 08 '25

Fuse box continuous power

0 Upvotes

I'm unsure if this is the correct forum for this but....I would like to hard wire in to my fuse box to use USB c to power a cell phone continuously, even when the ignition is off. I know there are dash cam kits, but I've read that they dont provide enough power to keep a phone charged. Any ideas?


r/autoelectrical • • Jan 13 '23

Should I become an auto electrician? What kind of tasks are carried out daily.

0 Upvotes

I'm a vehicle technician in training in a Ford dealer. And to be honest I'm kind of frustrated with the industry overall, and how physical the job is. I did expect the industry to be tough. But I've also started to do some sports competitvely. But I'm struggling to balance the physical demands of both of them.

I have seen a vacancy for a trainee cctv vehicle installer role. And I think it maybe a good entry level job so I can become an auto electrician in the future.

So that's my situation, and my questions are.

What are the daily tasks that maybe involved in being an auto electrician?

And is it as physically demanding as being a vehicle technician?

I understand that a full time job is always going to be tiring but I do feel like being a vehicle technician does take more out of me than the average job. I'm just looking at my options out there.


r/autoelectrical • • Mar 05 '24

Splicing USB C cable for dashcam, what connectors should I use for the tiny 26(?) gauge wires?

0 Upvotes

These are the wires.

The cable is about 6 feet too long so I'm going to shorten it up so I can make the wiring as clean as possible. My current aftermarket wiring is 18g and I'm using 22 to 16g spade connectors but the tiny wiring from the USB cable is too small for those spades. Is my best bet to solder and shrink tube the tiny wire to an 18g wire so it plays nicely with the rest of my wiring?

Any feedback is greatly appreciated.


r/autoelectrical • • Jul 28 '26

Our car audio works every other time after battery change.

0 Upvotes

I apologize if I am in the wrong place. Google has become useless.

My wife has a north american 2014 Mercedes ml 350. I do not know the trim level.

Her battery died and we replaced it.

 

After, their was no sound from her radio, and her powered lift gate no longer works (we'll deal with the lift gate after).

 

I checked the fuses, and could find nothing wrong.

 

Eventually I found a youtube video about “engineering mode” where the guy goes to menu 7.5, turns off the car, comes back 15 minutes later and it works.

 

And that works for us, but then the next time she drives the car, no radio again.

 

So she repeats that process, gets sound on her next drive.. Only to not have sound again on the following drive.

 

How do we keep her radio working?


r/autoelectrical • • Dec 24 '25

external LED help

Thumbnail
gallery
0 Upvotes

Hi everyone,

first time using reddit so apologies if there is an error in the post/pics.

I have recently bought this car with a bodykit and additional LED light strips in front bumper.

The 2 pics are of the actual car one from an old 2023 advert with all 4 light strips working, the other from a more recent advert with only 3 out of the 4 strips working.

Firstly, the one not working is definitely faulty as it doesn't work when wired to a separate supply.

I have bought a replacement LED and replaced the faulty one. They have individual 2 pin plugs supplying power behind the grill. Both plugs are supplying between 12 and 14 volts with engine running. Both plugs and lights have the same polarity to/from the plugs. I believe they have been wired/spliced to the original headlight loom just before it plugs into headlight.

Both LED strips work individually when plugged into either of the 2 plugs supplying power.

However, when I plug them BOTH in, only the new one works, the other (old) one goes off. Neither old lights, nor the new one have any power related markings on them.

The new one is much brighter if that helps diagnose what the issue might be.

Can anyone help explain in simple terms what the problem might be?

If I bought another LED strip to match the new one, are they likely to both work together at the same time?

Many thanks for any advice.


r/autoelectrical • • 3d ago

Phone charger behaving weird

Thumbnail
gallery
0 Upvotes

I'm trying to hide cables for a wireless phone charging mount behind the dash, using stuff I already had. Currently tapped into the cigarette lighter fuse to connect another 12v port with a charger plugged in leading to the wireless mount. Car is a 2004 Audi A4.

The phone is constantly switching between charging and not charging no matter if the engine is running or just ignition (gif of problem on last slide).

I assume its because the voltage is fluctuating but I don't know how to solve this. Can anyone help?


r/autoelectrical • • May 03 '26

Late night stoner question

0 Upvotes

So in gas powered vehicles we have alternators that charge the battery while running. Would it be possible to built alternators on an electrical vehicle that would charge the batteries while moving? In my head it would eliminate the need to charge your car. But i would imagine this would be a thing if it was possible

Edit: as I said it was a late night stoner idea. In my head, an "alternator" would hook up to the tire and as the tires rotates the "alternator" would charge then transferring that energy into the existing batteries. I have zero knowledge of electrical vehicles, it made sense early this morning, lol. Thanks for the responses


r/autoelectrical • • Nov 05 '25

No battery light on dash

1 Upvotes

Hi, wondering if anyone could help please. My sister’s VW polo 6R (2010 plate) broke down the other night, the car died and AA came out to jump it, he said the alternator was failing as there was no charge to the battery. He gave it the obligatory whack and it started to charge at 14V. Fair enough. So I bought an OEM alternator from a scrapyard and fitted it. However, there is still no charge to the battery. One thing I noticed is that when you turn the ignition on, the battery light on the dash does not illuminate at all. I noticed also when the car broke down that the battery light didn’t illuminate so I was surprised when it ended up being the alternator that was failing. I am assuming that there is an issue with the circuit to the exciter plug on the alternator? I believe it has two wires, one blue and one red. Has anyone ever had this before and how did you solve it? So far I have checked the voltage on the B+ lead on the alternator which is the same as the battery voltage, around 11.8V. I have checked all fuses I can find and they are all intact. I am going to look at the car when I have some time tomorrow, any advice would be great, thank you.