I have a BMW seat that I'm using for a simulator, without a car. Is it possible to control the lumbar support without a car? With a 12v battery? Through the socket?
The other seat adjustments are manual.
I haven't gotten to the wiring diagram yet, unfortunately.
I had an aftermarket 1500 watt inverter in my truck that I removed thinking that was drawing power but I re did the multi meter test and it still shows roughly 1.7amps being pulled. It pulls for a minute or so then drops down to .15amps which is fine. I am so confused at what is causing this.
The battery keeps dying (I drove this twice a week, 1 hour each time) and just replaced the battery one month ago (mechanics installed).
There are some weird lights/switches that were installed in the truck prior to me purchasing 3 years ago and I wonder if that is causing the drain - do I just need to pull every fuse at this point?
And yes, all lights are off, doors closed, glove boxes closed, radio off, etc.
I have a draw of what looks like 2 amps when everything is off and the car has been stationary for several hours.
How much higher is this value than would be expected for a car that is completely switched off?
How can I find what is causing the draw?
Thanks
UPDATE
Thanks for all the help. After connecting the monitor and leaving the car to sit for 30 mins the meter dropped to 0.48 amps which is still higher than the 0.05 people have recommended as the minimum. I then began testing fuses and found one fuse had been blown and fuse #17 was the problem. I removed fuse #17 and after leaving to stand for a while longer I got a reading of 0.10.
So I am trying to get my 1979 jeep j10 5.9 running enough to take it to one of you (a pro) with the battery on and ignition on I only measure 5.5v on the positive side of the coil nothing on the negative side. If I unplug the negative side I read 12v on both poles of the coil. When I unplug the battery my tester showed continuity between the positive wire and the block no continuity on the negative green wire. Any ideas?
Second in a attempt to run the truck can I hotwire the coil straight through this resister to the battery?
As the title says, on Friday afternoon I went to Batteries Plus for a new battery for my 1991 Ford F250 pickup with approximately 76000 miles on it. The employee hooked it up with the terminals to the wrong posts. I'm an old lady and didn't realize the posts are different sizes but did see he was having a difficult time getting them on although he was tenacious in doing it. He eventually said "Ohh, it's backwards" and turned the battery around. The terminals seemed to fit the posts that way. When he was done I started it briefly to make sure it would start and turned it off to go back inside to get my core refund. When I started it to leave, the radio wasn't working and the battery light on the dash was on. The battery light was not on and the radio was working when I drove there. I went back inside to tell them. The employee came back out and told me that if a customer has an after market radio (I do) it's their responsibility to tell them so they can hook up a battery tender prior to changing the battery so it doesn't fry the radio or other electronics. Nothing like that was said to me prior to the battery being removed.
I immediately became concerned that there may be damage to my truck from the battery being connected backwards with the battery light on and the battery voltage gauge now showing low when it was in normal range on the way there. The manager said he needed to call corporate to find out what to do but there would be no one there until Monday so took my name and number to call me. I was very hesitant to drive the truck in case any damage was occurring from it running. The manager said the battery light was on because it needed time to reset itself and it would reset if I drove it. He assured me it was safe to drive in the same breath he was telling me that they only get training in basic battery installation so didn't know about anything else. I left and went straight to my mechanic. They were short staffed so couldn't check it out then but he said it was likely there was damage with the battery light being on. They will look at it next week.
What's the protocol when something like this happens? I realize mistakes happen and what's important is the steps taken to correct it. The manager acted like there wasn't and couldn't be a problem from the battery being hooked up wrong. (I asked him if his employee told him he hooked it up backwards and he said yes, he told him.) The mechanic said it most definitely was a problem with the battery light on but he wouldn't know how big of one until they could check it out. The battery light remained on.
So I’m looking to add a second battery in the Bed of my truck and I have an accessory fuse block that I have lights, etc. wired to. It is a blue sea fuse block with a breaker in line that is close to the battery (from my understanding this is important to have it close to the battery) I’m wanting to run this power wire to a battery in the bed so my starter battery is only used for the truck.
Would it be okay to have a second breaker close to the battery in the bed? The setup I have now is clean with the mounting location for the breaker so I’d like to not remove it but I guess it’s not the end of the world. Is there anything unsafe about having both breakers? Would it work properly? Sorry I’m not so good when it comes to this stuff thank you for any help!
I'm sure this kind of device exists but I'm not searching for the right thing.
I have a 2013 C Max Hybrid. The entertainment unit pulls power even when the vehicle is off, and eventually kills the battery. I pulled the fuses for the entertainment unit and now it keeps a charge even after sitting for a long time.
Now I'm looking for solutions to get the entertainment unit working again. This seems like the simplest solution.
Essentially when the ignition is on, the relay allows all the other fuses to operate. Does this exist? If so, what do I search for?
'02 Ranger. Driver door lock switch didn't work in lock position. Removed switch, checked lock position - 100k ohms. Multiple times. Order an $80 switch. Install switch. No bueno. Are you f'ing kidding me!? Check old switch - 2 ohms i shit you not... Check new switch 2 ohms... I still damn old switch for intermittent high resistance but... Lock wire to next connector in cab isolated and found to be open... What a shit comnector to get to. Pulled speaker, pulled on lock wire - found completely cut in half in door jamb. Holy shit. Repair, reassemble, hated the fact i had to spend an extra half hour screwing with a double whammy.
The guy next to me had a crazy '13 mustang with funky door open response, radio on after locking car, dim headlamp on one side. Stupid shit like that. Took him all saturday but i told him to take off the two grounds next to the bjb. They had nuts on the underside but they were self tappers. Sure enough, body shop evidence. They had replaced that fender and the bolts had no metal in between the heads and the nuts. No grounds. Repaired, all issues resolved.
Is there a more simple way to figure out which wire connects to which existing wire than looking at the picture of my old pigtail and making note of what color wires go in what order to try to match them with the new junk yard pigtail clip. For reference the first picture is my old pigtail
I apologize if I'm not explaining myself correctly I am definitely new to electrical. Thank you for your help
I have done alot of improvements to my car since i got it a few months ago. I've replaced the original unit in the car with an android head unit and have also installed a rear reverse camera.
However, I want to add parking sensors into my car, I understand how to wire everything up at the rear of the car. However, how am i going to connect the sensor module to the Android head unit?
With the parking sensors would i need some adapter so that it would fit into the head unit? The unit itself definitely supports having reverse sensors and front sensors as when you go into reverse is shows you the lines and distance (obvs it doesn't show anything at the moment) but it understands that there could be one if that makes sense.
These sensors can also come with a display (which would look like the headunit display once fitted) so thats why i want to make it go onto this unit, It doesnt matter if it beeps or not i just want to have like the lines go something like this- see first image of stock camera lines
I have these spare cables which can plug into the head unit which aren't being used if they would help? Please see photos bellow, sorry there not the best. Where taken at night.
Hello everyone, I’m here to pick your brains about a problem I’m having with my 86 Nissan z31. When I push the light stalk forward it kills my regular low beams. They work normally if high beams are not on, I’m assuming it’s an issue with the control stalk which I have a spare of but I’m asking here if anyone else has run into a similar issue. When high beams are activated neither low or high beams work. The issue came about after an intercooler switch was fitted which makes me think this could be related although it could also just be a coincidence. High beams work once out of every 20 times I try to use them. I have her booked into a garage to investigate the issue but I’d like to consult the experts if you have any words of wisdom. Thanks 🙏
Just got my hands on a 2008 Mercedes Sprinter (ex-Ambulance, Australia) and while pulling out the Ambulance cabling I think I’ve shorted something. Pic is of the preliminary fuses. Is the bridge connection fried? If so, is it replaceable and what with? Do I need do do anything with the other fuses? I was planning to do a contact clean.
This is my grandson's Pontiac Vibe. The clips that hold the wire harness broke and it dropped onto the alternator. The wire covering is brittle for a couple of inches, fine after that.
My side-of-the-road repair was to stick a generic copper end, crimped with a random pair of pliers, then wrapped up with electrical tape. Put it back on the post, zip tied the harness on place, jump started and drove home.
No further melting in a 5 mile drive and it did charge the battery.
I'm not a mechanic and hate electrical problems.
About 2" of wire is gone.
Any constructive suggestions for a reliable fix on a student's budget?