r/WLED • • 3h ago

Power injection and power supply advice

1 Upvotes

Hi all,

I've been setting up 5V SK6812 LED strips with 60LED/m density, but I'm having some power issues. My setup is in the screenshot below - red shapes are the strips, yellow shapes are power supplies with ESP32 controllers and orange shapes are WLED segments (with start and stop LEDs) - I've named the segments by the controller they're connected with (Fink, Wendy, etc). I've optimistically set this up without power injections and found out this doesn't work well. The issues I have:

  1. The tail end of Fink Balk 2 is flickering

  2. All of Wendy is flickering on many effects and changing settings happens slowly and in very discrete steps

  3. Setting the brightness of Wendy above 20% or so causes the power supply to audibly whir. As I increase the brightness, it gets louder. I've swapped out my power supply for another one and it has the same issue.

My questions:

  1. How much power injection should I be doing (and where) along the Fink and Wendy to fix the voltage drop issues? Online recommendations seem to indicate every 0.5-1m or so, but the Mark, Bobby and Lisa strips are in the 1.5 - 2m range and don't have issues. I don't need to be running these at full brightness, I just want to solve the flickering.

  2. AI is telling me the whirring is caused by the power supply being close to its limit. Does anyone know if this is true? The power supply is 5V/20A and the max current needed according to WLED is 55mA * 308 = 17A, but I'd be surprised if it reaches that due to the voltage drop issues and limiting in WLED. Also, the whirring starts at low brightness too. Would upgrading the supply to e.g. 30A or 40A make a difference, or is there a different issue?

Thanks in advance for your help!


r/WLED • • 8h ago

QuinLED-Dig-Quad (v4) wire connectors: how to connect 14AWG wire? The connectors are so tiny

1 Upvotes

I have all kinds of ferrules, but the smallest that can fit 14AWG wire is too big to fit into the connectors [EDIT: the connectors to the LED strips].

If I try to just solder the end of the wire to stop fraying, sometimes I can get it to fit but it's not easy. Do I need to step down to a smaller guage just for the connector? I must be missing something simple....


r/WLED • • 15h ago

Need some help

2 Upvotes

So I have a small stage lighting project I’m working on. It’s more about ambience and prop lighting than full stage lights.

Currently I have an esp32 with some addressable 5v LED strip and just using wled off the phone. Everything is working well so far as a basic prototype.

I want to now figure out how to step things up to a more robust system which is capable off having multiple lights daisy chained around a stage. Just as a rough estimate I’d like to have 3-5 different LED strip lights around the stage and to have them daisy chained so the chase effect can go between the different lights.

So I’m trying to figure out a good way to get data signal between them, either by sending it between all the lights in a daisy chain (this could end up being 15-20m) or is there a controller or an output device I can use that would allow me to have the lights wired back to a central point yet still give me a chase effect. I don’t really want the lights to only do the same effect at the same time.

So if you have some tips or help for me that would be great as I’m a bit lost as to which parts I’ll need and how to simplify it so I can just hang my lights and then connect the wires between them or back to a central point.

Also if there is a good all in one control box for this. Thanks heaps


r/WLED • • 15h ago

Help with pinouts for hub75

Post image
1 Upvotes

i have a" ESP32 38 Pin WROOM-32 V5 Development Board Dual Core USB C WiFi BT NodeMCU Dev "

I also have a hub 75 breakout board with these pinouts.

Do you guys have any idea which version of hub75 activated wled I can use for this?


r/WLED • • 18h ago

Ceiling light

Post image
1 Upvotes

Hello everyone.

I am trying to make some WLED Light under my ceilling in my living room. In the image there is a scheme how I am planning to do this. I don't have much experience with WLED project that why I want ask you, more experienced people if that will works or something need to be change or maybe you have different ideas. As you can see there will be Three strips of LED: 4,2m, 4,0m and 7,6m, ecause of lenght of the ceiling/wall. power supply and LED Controller will be in the first corner betwen 4,2 m and 4 m wall 1,5 m under ceiling. So the power cable lenght will be

5,7m, 1,5m, 1,5m, 5,5m, 5,5m, 9,1m.

and First data cable 5,7mm other two only few cm. Led be 12V and thats why i want put Power on two sides of the strip to be sure that there is no power drops.

I want use WS2815 12v LED , GLEDOPTO controller, Not sure what power supply.

As I said I am new in this did some research but as allways there is some concerns and want to do this right because dont have a chance to change anything when everythign be connected.

Hope i describe everything clear and most of You will understand.

Thank you very much for your help.


r/WLED • • 18h ago

How to best put a strip on this kind of TV?

Post image
2 Upvotes

Hey everyone! I’m making use of the Black Friday Sales and am finally upgrading my TV. As this has been the plan for quite some time now I’ve held off on installing a light strip on the back of my current TV bc I knew it would be replaced sooner rather than later. I never looked at a specific TV to put my ambilight setup on as it depended on which would go on sale. The TV I will get, that makes the most sense is one of those, that have more depth to them at the bottom and are extremely thin on top, slightly thicker than the display itself. I’ve attached the best images I could find online.
The problem:
I'm a bit scared to install a light strip on this thin of a part, bc I wonder if I might break it. Also I’m unsure how to handle the fairly big jump in thickness at the bottom and depending on how far away from the edge I should place the strip also the bottom half of both sides.
Does anybody have experience with this? Would love some advice, so thanks in advance for your response!

PS: it’s the new Sony Bravia 6 65A65


r/WLED • • 20h ago

LEDs for each stair

Post image
0 Upvotes

r/WLED • • 21h ago

New problem

0 Upvotes

Im having a problem with my lights. They have started to bug out on me several times a day, and I don’t know how to fix it. Right now they are off, but in about 3 hours they will turn themselves on and just pulse white lights. I can set them for anything, and within a few hours, they will switch back to the white strobe. I know it updated, but it started before the update. Any ideas? Anyone near Fort Worth willing to check it out with me? I want to get it cleared up before Thanksgiving, if possible


r/WLED • • 22h ago

Anyone build rope lights using WLED and Seed Pixels?

0 Upvotes

I am in the process of putting together the BOM for what I want to build and would like to run it by folks here for any feedback.

# Custom Modular 18-ft WLED Rope Lights — Bill of Materials (BOM)

**Project Overview:**

* **Scale:** 5 Columns, 2 modular 18-ft ropes per column (10 ropes / 180 ft total)

* **Design:** 12V WS2811 seed pixels pulled through 1/2" ID clear vinyl tubing with 3-pin xConnect screw ends so ropes can be run either **in parallel** (2 per column, e.g., double-helix) or **chained end-to-end** (36-ft single run with plug-and-play power injection).

* **Control:** 1 dual-output WLED controller per column (synced via WLED UDP Sync / DDP).

---

### 1. LEDs & Tubing (10 × 18-ft Ropes)

* **12V WS2811 Seed Pixels (Clear Wire, 3-Pin)**

* *If building 2.5 cm (~1") pitch (~220 px/rope, 2,200 px total):* **2× 1,000-ct rolls + 2× 200-ct strands** *(200 spare)*

* *If building 5 cm (~2") pitch (~110 px/rope, 1,100 px total):* **1× 1,000-ct roll + 1× 200-ct strand** *(100 spare)*

* **Clear Flexible Vinyl Tubing:** **200 ft** of **1/2" ID × 5/8" OD** (or 1/2" ID × 3/4" OD) UV-resistant PVC *(10 × 18-ft cuts + 20 ft spare)*

---

### 2. Controllers, Power & Enclosures (5 Column Boxes)

* **WLED Controllers:** **5×** Gledopto GL-C-016WL-D *(ESP32, 12V–24V, dual data outputs)*

* **12V IP67 Waterproof Power Supplies:** **5×** **12V 8.5A (100W)** for 2.5 cm pitch *(or **12V 5A (60W)** if using 5 cm pitch)*

* **Weatherproof Junction Boxes:** **5×** IP65/IP66 hinged ABS enclosures *(~6"×4"×3" or 8"×6"×4")*

* **Waterproof Cable Glands (PG9 / PG11):** **15–20×** *(3–4 per box for AC in + xConnect leads out)*

* **Inline Blade Fuse Holders + 5A Fuses:** **15×** *(16–18 AWG waterproof holders; 2 rope outputs + 1 injection lead per box)*

* **Wago 221 Lever Nuts:** **1 assortment pack (~25 pcs)** of 3-port (`221-413`) & 5-port (`221-415`) for `+12V` and `GND` distribution

* **Outdoor AC Power Cords (SJTW):** **5×** *(1 per column box)*

---

### 3. Waterproof Connectors & Power Injection

* **Female 3-Pin xConnect Pigtails (18 AWG):** **25×** *(2 per controller box + 1 per rope output end + 5 spares)*

* **Male 3-Pin xConnect Pigtails (18 AWG):** **20×** *(1 per rope input end + 1 per injection lead + 5 spares)*

* **xConnect Waterproof Screw End Caps:** **15×** *(to seal the unused top Male connector on each column + 5 spares)*

* **3-3-3 xConnect Power Injection T-Splitters:** **5×** *(1 per column; used between Rope 1 & Rope 2 when chained end-to-end at 2.5 cm pitch)*

* **18/2 Low-Voltage Outdoor Wire:** **100 ft spool** *(for 5 × ~19-ft `+12V`/`GND`-only power injection jumpers up to the T-splitters)*

---

### 4. Sealing, Soldering & Pulling Consumables

* **3/4" (19mm) Adhesive-Lined Marine Heat Shrink (3:1):** **1 roll / pack** *(~3–4 ft total needed to seal pigtail-to-vinyl tube ends)*

* **22–18 AWG Waterproof Solder Seal Wire Connectors:** **100-pack** *(~60–75 splices needed)*

* **100% Neutral-Cure Clear Silicone Sealant:** **1 tube** *(must be oxime/neutral-cure—avoid acidic acetoxy silicone so copper doesn't corrode)*

* **Pull String & Silicone Spray:** **1 each** *(mason's twine/fish tape + dry silicone lube for pulling pixels through the 18-ft tubes)*

* **UV-Resistant Zip Ties / Clear Mounting Clips:** **100-pack**

---

### Quick Wiring & Build Notes

  1. **Verify Pinout First:** Always check `+12V`, `DATA`, and `GND` with a multimeter in continuity mode before powering on—wire markings on seed pixel rolls vary by batch.

  2. **Power Injection Safety:** On the injection leg going into the 3-3-3 T-splitter, connect **only `+12V` and `GND`** (leave the center `DATA` pin disconnected), and always feed it from the **same** 12V power supply running that column's controller.

  3. **Test Before Sealing:** Power up and test every rope on the bench with WLED before applying neutral-cure silicone and shrinking the 3/4" marine heat shrink over the tubing ends.


r/WLED • • 22h ago

Strip Identifizieren

Thumbnail
gallery
1 Upvotes

Kann mir jemand helfen und mir sagen was das für ein Strip ist?

Die Pins sind mit 12v DO W und GND beschriftet.

Ich vermute es handelt sich um ein WS2811 mit einer Leitung für RGB und einer für Weiß, bin mir aber nicht sicher.

Was müsste ich in WLED einstellen?

Danke


r/WLED • • 23h ago

WLED Controller for 15m 24V WS2805 cove lighting + audio sync (GLEDOPTO SonicX vs. Elite 6D-EXMU vs. alternatives?)

Thumbnail reddit.com
2 Upvotes

r/WLED • • 1d ago

WLED Window Candle

Thumbnail
gallery
51 Upvotes

I have been wanting to make this for years and finally did this spring. A few revisions later and I'm doing a kickstarter to gauge is there's any interest before I bother with getting them certified. I've been testing them for about 6 months, and have about 2 dozen running now at home. The photos don't really do it justice, especially at night but you get the idea.

The effect in the photos is PS Fire.

Thoughts or questions let need know! Thanks.

https://www.kickstarter.com/projects/mikeat/window-spark-wifi-candle


r/WLED • • 1d ago

[SOLVED] Gledopto GL-C-017WL-D (ESP32 WLED) not turning on / flickering after factory reset

Thumbnail reddit.com
1 Upvotes

r/WLED • • 1d ago

WLED bootet unkontrolliert neu

0 Upvotes

Hi Leutz

Ich komme aus dem schönen Sauerland und werkel mit WLED seit ca. 5 Jahren. Ich habe verschiedenen Sachen gemacht. Garagenampel, beleuchteter Leitpfosten, Aussenleuchten am Haus, LED Beleuchtung innen, ...

Seit ein paar Tagen habe ich ein Problem, was ich nicht erklären kann.

Von jetzt auf gleich gingen alle WLED Systeme gleichzeitig an.

Meine Bedingungen sind immer gleich. Meanwell Netzteil 5V, ESP8266, WS2812 und die Version V0.13.0-b2 Toki. Die Netzteile sind immer an die Verbraucher angepasst. Sie gehen bis 12A. Schalten kann ich sie über WEB Oberläche, mit Alexa, mit iobroker oder von einem Lichtschalter. Dazu gibt es ein Potentialfreies Relais.

Also habe ich mich auf die Suche gemacht. Die Skripte und die Instanz abgeschaltet. Problem bleibt. Alle dns Einträge gelöscht. Ich hatte die Sync in Verdacht. Keine Besserung. Ich starte ein Preset nach dem booten. Dieses auf Null gestellt und siehe da alles bleibt aus. Allerdings leuchten sie beim ersten einschalten orange mit den default Werten. Es laufen keine Timer oder Makros. Ich sehe an der uptime, dass sie vermutlich gerade neu gebootet haben. Es passiert an 15 Geräten gleichzeitig. Somit schliesse ich die Hardware aus. Mein Testboard mit 3 LED's und auch ESP8266 habe ich mal auf Version 16 geuppt. Das läuft seit 20 Stunden und hat noch nicht neu gestartet.

Wenn, dann starten alle Geräte zur gleichenzeit neu. So als wenn alle ohne Spannung grwesen wären. Anhand der Netzteile, schliesse ich das aber aus. Sie halten die Spannung über mehrere Sekunden. Zudem sind die Geräte auf alle drei Phasen im Haus aufgeteilt und sonst verliert auch kein anderes Gerät seine Einstellungen.

Das einzige, was letzte Woche war, mein Hauptzähler wurde getauscht. Das sollte aber nichts damit zutun haben.

Ich verzweifel hier so langsam. Alle Systeme laufen über drei Jahre problemlos und jetzt das.

Hat das auch jemand oder eine Idee?

LG aus dem Sauerland

Jörg


r/WLED • • 1d ago

Bts 2026.

Thumbnail
youtube.com
6 Upvotes

A little bts that I been working on for the past 2 weeks. These will get install soon. All run by wled.


r/WLED • • 1d ago

Weird Wled problem

10 Upvotes

I could really use some help friends, I'm banging my head against the wall at this point.


r/WLED • • 1d ago

RGB colors and brightness mismatch

Thumbnail
gallery
4 Upvotes

I have two levels both on separate boards I ran a update a while back and now the RGB color values are not the same and the brightness is much more dim on one of the boards. Any idea?


r/WLED • • 1d ago

Help meee wled system is not working

6 Upvotes

Hello wled friends. I have a big wled setup, it's never given me a single issue since I built it, I added a wled plugin to my streamdeck, it worked perfectly fine, and a day later this is all I get. The ceiling/wall perimeter LED is run off a wegolot esp32 which are like 30 something bucks, the shelves and everything else runs off legit esp32 dev boards, never given me a hard time, now all at the same time they aren't working. Which makes zero sense because every shelf has its own power source and esp32. Also on the wled app, all the esp32 dev boards have lost connection to the internet. If anyone could help that would be unreal. Thanks yall,


r/WLED • • 1d ago

Best controller for permanent christmas light setup

Post image
4 Upvotes

I installed this kit recently but the app/control leaves alot to be desired. It uses the surplife app but I would like to use wled if that would work. Which controller will allow me to use wled and work with these lights?


r/WLED • • 2d ago

Can Xlights integrate with live audio?

1 Upvotes

I have a personal radio station using station playlist software that I want the audio to synchronise with X-lights. I am thinking about having Station Playlist trigger X-lights to play certain sequences when a part of the show is played over the radio station. When that sequence isn't triggered, or has ended, I want X-lights to just create synchronization to whatever is playing. Is this possible? Any ideas?

Im leading govee prisim lights as I want the govee lights to be on the house 365..


r/WLED • • 2d ago

patterns of 3D array (R,G,B) ,what other dynamic features or interactions could I add to my LED panel?

2 Upvotes

r/WLED • • 2d ago

will it WLED: Govee Cone Tree (episode 14)

Thumbnail
youtube.com
25 Upvotes

r/WLED • • 2d ago

Trimlight Chicago

1 Upvotes

I had Trimlight installed awhile ago and I was interested in seeing if it would be easy to add WLED control to it so I can include it in my xlights sequences.

Does anyone know if this is as simple as disconnecting power and leds from the Trimlight controller?


r/WLED • • 2d ago

Got that holiday spirit

42 Upvotes

Wanted to share the last project I cranked. Getting that holiday spirit going! Inspired by the govee ball. Will post model to maketworld in coming days