r/WLED • • 5d ago

Weird Wled problem

I could really use some help friends, I'm banging my head against the wall at this point.

12 Upvotes

15 comments sorted by

1

u/Outrageous-Kick-2699 5d ago

I assume you power the esp from the same psu as the leds? Does the freeze happen when you have less leds connected? I would say it’s a power glitch in the esp.

1

u/RageReviewYT 5d ago

Yup, it's all connected together. One 150 watt psu, it runs about 32 feet of leds, I just did the math, at peak brightness 32 feet will consume 192 watts. And that psu also powers 2 esp32's. I think I'm way under powered.... damn. What's puzzling to me is, I also have a 2nd 150 watt psu powering a much smaller strip, about 20 feet, I keep it on low as it's just accent lighting under my desk. And it also struggles like crazy on startup. Which makes me think it's a software issue. I'm so lost lol.

1

u/Outrageous-Kick-2699 5d ago

Try the power limit in wled. Go 20% under max power of the psu, see if this helps.

1

u/RageReviewYT 4d ago

I already had it set lower but I'll turn it way down and see if that helps at all. Ty

1

u/Low_Tomato_6837 4d ago

Retired electrical engineer here, most of the consumer power supplies will begin to derate at 80% of listed capacity. Some even earlier. I just had one, rated 25 amps at 12 VDC, voltage fell to 9.1 volts at only 6.5 amps.

You need to check voltage at load to see but you probably need a much larger power supply.

2

u/RageReviewYT 3d ago

Thanks man! After all my testing, it really does seem like a power supply issue. The power supply goes into that plastic dish, where then I have a couple wire connectors that split the incoming power to the esp32 board. The power continues through the connectors to the actually leds, along with the data wire from the esp32. I mean, I've been driving the PSUs pretty hard for two years, they're very cheap so, many it's time to upgrade to something more substantial.

1

u/RageReviewYT 5d ago

The glitch/slow startup happens no matter how many LEDs are connected. Like I said in my previous msg, I have a smaller strip under my desk, with plenty of power, and it too struggles to start up, after about 10 minutes or so, it'll change from random colors to the effects that it's intended to display.

1

u/ChocolateThese7545 4d ago

I’m confused why the esp32 on top of the gledapto ? (No hate could be dumb question just curious)

1

u/RageReviewYT 3d ago

There's 4 controllers all controlling separate areas of the room. The gledapto being one of them. I wanted to see how it would word compared to the esp32 dev boards, so far it's been far more consistent.

1

u/ChocolateThese7545 3d ago

Ohhh that makes a lotta sense

1

u/mushmouth26 4d ago

I had an issue like this awhile back on a smaller project. It was a wire gauge issue. Where the wires where to small for the needed amps to flow correctly. Like there was to much resistance in the smaller gauge wire. So my ESP32 wasnt getting enough voltage to function properly.

1

u/RageReviewYT 3d ago

Hm, I wonder if powering them via usb would solve my problem.

1

u/mushmouth26 3d ago

have you checked the voltage coming out of the quick splice terminal that running into your esp32 when on to make sure its proper voltage. What voltage are your LEDs?

1

u/thesnowpup 4d ago

The esp is definitely getting power starved somehow.

Try injecting power directly between the esp and the strip.

1

u/upeenarce 3d ago

Are they all sharing the same ground? I had similar issues when i had accidentally given different grounds to the lights than the esp.