r/Modded_iPods • • Mar 29 '26

iPod Pro V2: AirTag, Note 9 4000Mah Battery, USB-C, Bluetooth, Haptics & Custom Backplate Builds

Thumbnail
gallery
962 Upvotes

V2 of my custom iPod backplate is done!
These are two nearly identical builds I completed for u/Friendly-Bag2512: a 5th gen and a 7th gen, both 512GB with the same set of mods and internal layout.

This version is mostly a refinement of V1, tightening tolerances, simplifying assembly, and fixing a few design choices that didn’t age well.

Mods included in these two builds:

  • Gutted AirTag

  • Note 9 4000mAh battery

  • UGREEN Bluetooth transmitter with LED indicators

  • 512GB iFlash uDual

  • USB-C charging and 2.0 data transfer

  • iPhone 7 Taptic Engine

  • Relocated lock switch

Both builds also have custom faceplates that were stripped of their anodising for a more industrial look compared to stock or third-party colors. The 7th gen received a brushed finish, while the 5th gen has a polished finish. Center buttons also received a special swirl polish.

AirTag integration (Main V2 improvement):
The AirTag is fully integrated into the thicker backplate variant and powered directly from the iPod’s main battery. Instead of a coin cell, I’m using an MCP1703-3002 LDO regulator to step it down to a stable 3V supply.

This makes the AirTag effectively permanent, no battery swaps needed. The MCP1703 works well here because of its low dropout and very low quiescent current. It only draws around 2µA at idle, so the impact on battery life is basically negligible. The AirTag still retains its internal speaker. It’s quieter than stock due to being enclosed, but still audible when triggered through Find My.

The Bluetooth button has been redesigned to use standard 6×6 tactile switches instead of the SMD button from before. That change makes it more reliable and easier to source. It also removes the separate clamp piece and one screw, simplifying both printing and assembly. The old clamp worked but was fiddly and awkward to put together.

Dual Bluetooth LEDs (new in V2):
Bluetooth is controlled by a momentary switch next to the AUX port. The button is printed in translucent PETG, with the LEDs mounted directly above it to shine through for a clean indicator.

I also finally got dual LEDs working to show the Bluetooth board’s state, which I couldn’t get right in previous builds. The red LED wouldn’t power on initially.

The issue came down to where I was tapping the signal. Originally I tapped on the LED side of the resistor, but that point cannot reliably drive a second LED.

After probing:
LED side of resistor: ~2.23V when ON, ~2.95V when OFF
MCU side of resistor: ~60–80mV when ON, ~2.95V when OFF

Tapping the MCU side of the resistor fixes it. You get a proper low when the LED is on and a high around 3V when it’s off, which makes it usable for driving another indicator LED. The red LED just needs its own series resistor (1k SMD works well).

Backplate variants:

  • One version with space for a gutted AirTag

  • One version without

  • Both versions support either an iPhone 7 or iPhone XS Taptic Engine

Thickness options:

  • Thick (AirTag): 17.4 mm

  • Thin: 15.3 mm

The thicker version also makes internal assembly noticeably easier thanks to the extra space. Both have a weighty feel, slightly heavier than a stock HDD model due to the large battery.

Backplate construction:
This version supports both fully printed backplates and hybrid builds using a 1 mm aluminium rear plate mounted to a printed frame using 5 M2 screws.

Instead of the original clips, u/daddyfatflab and I developed a design that uses six M1.4 screws. These pass through the faceplate and thread into the midframe, securing the two halves together.

Some small Dremel modification to the midframe is required: I'll talk about these in more depth when I release the models on Printables soon. It’s quick work, but important to note for builders. This fastening system makes the assembly much more solid and easier to work on compared to the original clips.

Other details:

  • Bottom-left notch on the back is for the Bluetooth antenna

  • Lock switch relocated to the left side to make room for the battery and USB-C board

  • Still uses the original switch and flex cable, just removed from the stock bracket

  • Full 30-pin functionality is retained, so it remains compatible with docks

I'll upload all the files for free on Printables soon, with a guide to help you with your own build!


r/Modded_iPods • • Feb 16 '25

Boxy Pixel's First iPod

Thumbnail
gallery
908 Upvotes

r/Modded_iPods • • Apr 06 '25

The most modded ipod in existence?

Thumbnail
gallery
846 Upvotes

Mods include usbc, taptic engine, bluetooth, speaker, wireless charging, 2000 mah battery, sd card storage, and a custom (thick) clipless backplate


r/Modded_iPods • • Feb 04 '25

Picture i plugged it in and it gave me a virus

Post image
727 Upvotes

r/Modded_iPods • • Feb 06 '25

Picture Hey, everyone! I just wanted to say thank you for the suggestions and info on my first mod. Heres how this bad boy turned out. Its so cool.

Post image
661 Upvotes

r/Modded_iPods • • Feb 05 '25

1TB iPodPro

Thumbnail
gallery
527 Upvotes

The nostalgia is flowing


r/Modded_iPods • • Jan 31 '25

Question Thoughts

Thumbnail
gallery
468 Upvotes

Which Atom looks the best?


r/Modded_iPods • • Mar 08 '25

Custom First of its kind, clipless ipod case prototype

Thumbnail
gallery
424 Upvotes

r/Modded_iPods • • Jan 08 '25

Advice Atomic Classics

Thumbnail
gallery
424 Upvotes

What is your thoughts.


r/Modded_iPods • • May 06 '25

Picture Obsessed 🟣✨

Thumbnail
gallery
423 Upvotes

Souped up 5.5g with an iflash quad, 3000mah battery, click wheel and thick backplate from Elite Obsolete. Screen has some white cloudiness from moisture or something so gonna replace that eventually but I am very happy! IEMs are KZ ZS10 pros with a purple Linsoul cable and kbear tips.


r/Modded_iPods • • 24d ago

Picture Transparent Orange Resin iPod with NFC

Thumbnail
gallery
378 Upvotes

A few weeks ago on r/ipod I posted about adding NFC capabilities to an iPod. I was quite rightly struck down as I was informed NFC cannot pass through the metal backplate. A few people told me just put a case on it and add it to the back of the case that sort of thing but I wanted to also have a transparent back as I thought it would be fun. I had 3 custom printed backplates. A clear transparent, transparent green, and transparent orange. Then, I bought a small NFC tag that we use here in Hong Kong (it says Mong Kok - my home metro station). I hope you like my final (for now) version. I used the orange one as it matched my click wheel. I may get a transparent orange faceplate to complete the job. We shall see! Credit to dianexis on thingiverse for the mold and Pendleton115 for the remixed version that is resin compatible.

Edit: The link to the stl file I used is here

Thin version is here - disclaimer being that I haven't used this one before but the resin version above used this as the basis model


r/Modded_iPods • • Feb 27 '25

Question WOLFSON DAC

Post image
373 Upvotes

Hey everyone ! Happy modding :)

I have already modded the 6/7th gen on the right with I flash solo 128gb and 2000mah battery and now just won an auction for the 5.5 gen on the left with the sought after WOLFSON DAC :) after listening them back to back no EQ on high fidelity headphones I can clearly tell,

that I am unable to spot any difference 😂. Am I the only one with such bad earring qualities or are any of you guys able to clearly differentiate the sound characteristics of those two DACs ?

Anyway, I am looking forward to modding this 5th gen as it will be way easier to open this bad boy !

PS: I am based in Switzerland and it seems that since Jan 1st we are not able to get batteries from Aliexpress anymore. If anyone is able to provide guidance or help, that would be much appreciated ! I have the 30gb (thin) 5.5 (looking forward a 2000mah rectangular battery)


r/Modded_iPods • • 19d ago

Picture Transparent Orange Resin iPod v1.5

356 Upvotes

Many people here were very receptive to my original post. I thought you might appreciate my final(?) tweaks. I added a transparent faceplate and clickwheel button to round out the transparent orange look. The oranges are very similar but not exactly the same color so I may still change it up or go back to the two toned. We shall see! I also installed the new ipodwizard 1.3.5 (credit to u/SonyCaptain) and changed my ipod to "Dark Grey" mode.


r/Modded_iPods • • Feb 26 '26

Review Thoughts on this beauty. 7th generation 1tb iflash mega battery

Thumbnail
gallery
356 Upvotes

I like it do you? What don’t you like?


r/Modded_iPods • • Feb 02 '25

Chroma Theme: Zip files ready for download

Post image
326 Upvotes

r/Modded_iPods • • Apr 11 '26

Modded Center click-wheel: Opaque vs Translucent

325 Upvotes

I prefer the solid look, since the button itself is not perfectly centered, making the clear one look cheaper. However, I do understand the appeal and on some models, I do use the clear.


r/Modded_iPods • • 29d ago

iPod dual Flash Card Brackets - Print your Own!

Thumbnail
gallery
324 Upvotes

I made these brackets for the generic dual microSD adapters used in iPod flash mods. They hold the adapter neatly in the midframe and keep the HDD ribbon cable from sitting in an awkward bend.

The bracket fills the gaps around and under the board, with cutouts for the chips, so it doesn’t make the assembly any thicker. It stays at 3.7 mm, just like the adapter on its own, and makes the inside of the iPod look a lot tidier without compromising the fit.

There are two versions: a standard one that’s a bit easier to print, and one for my USB-C modded backplates. They’re both free on Printables if you want to give them a try!

https://www.printables.com/model/1888468-ipod-dual-flash-card-brackets


r/Modded_iPods • • Mar 07 '25

Advice Thoughts

Thumbnail
gallery
322 Upvotes

Which one do you like the best?


r/Modded_iPods • • Apr 10 '26 Popcorn

Picture New Atomic Faceplates colors coming soon!

Thumbnail
gallery
320 Upvotes

More than 50 new colorways coming soon for your 5th generation iPod.


r/Modded_iPods • • Jan 29 '25

Chroma theme now available

Post image
311 Upvotes

r/Modded_iPods • • 21d ago

Wish me luck

Post image
306 Upvotes

13th year anniversary gift for me and my wife, first time opening an ipod.


r/Modded_iPods • • Mar 30 '26

My Daily…

Thumbnail
gallery
298 Upvotes

iPod classic modded with Bluetooth and AirPod max…


r/Modded_iPods • • Jun 25 '26

Tweaked the rockbox oscilloscope code!

296 Upvotes

For those of you unfamiliar with rockbox, it has a built-in oscilloscope which is pretty cool.

I loved the Rockbox oscilloscope demo so much that I decided to edit and recompile the source code on my ipod to make some changes. (I hope I'm not breaking any copyright laws)

  1. cycling through colours. I can't decide which colours I prefer though

  2. the "rate" of the colour cycling vaguely responds to the music. This is done by increasing the cycle rate when the volume suddenly jumps, which overall makes the colour change in time with beat drops, ect (I'm working on a better system)

If you've never used the oscilloscope plugin you can check it out, it's a nice green colour by default.

UPDATE!!!
I have a github page if you want the code, I only have it for the ipod video 5.5 but if you DM me your device I can make another version for your named device in just 1 day!!

13/07/26 EDIT: Having some technical difficulties (ipod battery competely dead) so I'm putting all the coding on hold for a few weeks. sorry!

EDIT: WE'RE BACK IN BUSINESS, SEND ME PROJECT REQUESTS IF YOU WANT

https://github.com/D4ntesinferno/better_oscilloscope/tree/main

Copyright (C) 2004-2006 Jens Arnold (tweaked by me)

r/Modded_iPods • • Jul 21 '26

Bluetooth Mod Finished my iPod Classic mod: 3000mAh, iFlash-uDUAL, 256GB, Bluetooth

Thumbnail
gallery
274 Upvotes

Finally finished my iPod Classic mod.

Specs:

  • 3000mAh battery

  • iFlash-uDUAL

  • 2×128GB microSD cards (256GB total)

  • Internal bluetooth mod

  • Switch to enable/disable Bluetooth

  • Bluetooth pairing button

The BT switch disconnects power from the module when it's not needed, so it behaves like a normal wired iPod and doesn't waste any battery. The pairing button is mounted internally so I don't have to open the case to connect new headphones.

It took a fair amount of fitting everything inside, but it all came together in the end. So far it's been working well, and it's nice having 256GB storage, much longer battery life and the option of wired or BT audio in the same device.


r/Modded_iPods • • Mar 03 '25

Modded First Mod: iPod Mini 128GB/Battery

Thumbnail
gallery
267 Upvotes

For a Newbie, mostly hassle free. MCM Battery, iFixit SD Adapter and 128GB Lexar SD (heard sandisk have issues with iFixit)

  1. I did get stuck on the end pieces, I was digging too deep at first but once you feel out the thickness of the plastic (1-2mm?) it’s easy to pop them off with the iFixit tool.

  2. I ended up having to Rebuild the MDR on the SDR, delete the partition and then format the memory to FAT32 otherwise I’d get the dreaded folder icon. This video helped me out.

https://youtu.be/Jt_xv6uqgAw