I haven’t had this product long, and I’ve already have multiple issues with it. Now it’s got to the point of it not even being able to pull a shot? After seeing so many people already having issues with these machines. I think the least they can do is extend the warranty for everyone on these things.
I am posting this so anyone unfortunate enough to face the same issue can fix it themselves more easily than I did.
Main Issue: Grinder doesn’t respond when pressing the button after trying a hard restart.
Causes of this are typically one of two things, one being a spent board fuse and another being a faulty/ broken hopper sensor. This sensor is the one responsible for ensuring the grinder stops running automatically and making it impossible to run without the hopper on.
To find out if you have either of these faults you must first open the machine. NOTE! This will void your warranty if it wasn’t already obvious, also UNPLUG THE MACHINE BEFORE OPENING IT UP.
To open the machine, unscrew the two screws on the bottom of the machine and then pull the plastic back cover off carefully. It will feel like you are going to break the cover, if you are careful and do not yank it off it will be fine.
The screws are located here:
Next you will see the inside of the machine.
To first test for a broken fuse you can use a multimeter to check for continuity inside the fuse. This is easily done by unscrewing the front pcb board and then contacting the fuse pins on the back of the board. If the fuse is ok then you are most likely dealing with a faulty sensor. There is no easy way to check this for sure since one of the leads to it goes down into the base of the machine. However, it is the next most likely cause of failure. This can be ”fixed“ by permanently connecting the leads going to the sensor to trick it into always being on. NOTE! This will make it possible to run the machine with the hopper off thus creating a safety hazard, perform at your own risk.
The wires going to the sensor and the fuse itself are depicted below.
The way I achieved connection of the wires is through a Wago Quick Connector. Simply cut each wire and then connect the lead going into the board and the lead going into the lower part of the machine. The other leads are now useless and do not receive any live power so it is perfectly safe to cut them down and leave them tucked into the machine. My result is shown below.
This immediately restored functionality. NOTE! Please ignore any shrink tubing and soldering seen above as because I did not have any schematics or prior experience seen online I had to actually cut almost every wire and test them to see which one went to the sensor.
For anyone looking for help on an issue with a fuse as of 11/21/26 there is no information I can find out what type of fuse is needed. However, I hope this helped you locate it and understand how to remove it. Obviously, that procedue would require actually soldering.
NOTE: This happened to my machine after about 3 months of heavy use.
I pre-ordered the Fellow Espresso Series 1 and have been using it for six months now, and my experience has been nothing but positive. Honestly, I don't have anything negative to say about it.
One of the biggest questions people had early on was the build quality, given that the majority of the machine is made of plastic. Half a year in, it still feels solid and well put together.
In terms of workflow, I don't actually use the volumetric dosing I prefer pulling shots manually. Because different coffees, roast levels, and other variables change how volumetric behaves, doing it manually gives me much better control. The custom programming has been a highlight, too I just dialed in and programmed a profile for a Kericho Kenyan decaf, and the cup came out genuinely lovely.
Hi all! I got an Espresso Series 1 as a gift this week (US 120V model, black, firmware 2.5.15), and it has behaved like this since the very first use:
1. No pressure on any profile
The gauge sits at ~1 bar for the whole shot, and the phase shows "INFUSION" the entire time.
Same result on every profile I've tried, both Fellow's and others.
Even with a pour-over grind, the shot runs ~50 s with only thin drips, and the machine tells me to grind coarser because the shot was too long.
2. Hot water spout: only a thin, pencil-like stream.
3. Steam: pressing the steam button makes the pump pulse roughly once per second, but no steam comes out of the wand. A short purge does happen when I put the wand back in the home position.
Setup: 131V outlet on a 20A circuit (plug adapter, since I'm outside the US).
What I've tried so far:
Several profiles
Grind sizes from espresso-fine to pour-over coarse
My guess is that all three symptoms come from the same thing: low water delivery from the pump or inlet (air lock? stuck tank valve?), not grind or profile settings.
Questions:
Has anyone had this on a new unit? What fixed it?
Is there a priming routine that worked for you after an air lock?
What pressure should a backflush-disc (blind) test show on a healthy unit?
Roughly how many grams does a normal unit dispense in 10 s from the grouphead (no portafilter) and from the hot water spout?
Did System Calibration (Settings > Setup) on 2.5.15 change anything for you?
I already have a call scheduled with Fellow support, but I'd love to hear from other owners first. Thanks!
Just purchased one on Amazon on Black Friday sale. Those of you who have it - does it really jam as much as Amazon reviewers say? Also, do you just grind all coffee beans at setting 6-7 for filter coffee prep (like Moccamaster) or would you vary the grind per bean, say different grind for medium roast vs Ethiopian vs French Roast? Not quite sure how to change the grind size based on bean or whether I even should for filter coffee.
Anyone have this issue before and know what could be the problem. Just happened this morning and now the steam wand in constantly dripping water even when the machine is turned off.
I used my opus 2 once today fresh out of the box. Ground fine, then would not grind again. No motion when pressing button.
I took off the hopper and removed the burrito basket to confirm no clogs or other issues. Then reinstalled. Still no luck.
I have repeated that process with power cycling a couple of times but it has not run again.
When I lock the upper basket in place I get a beep.
Seems like maybe a hopper sensor issue?
Any tips would be appreciated before returning.
Thanks!
**Update:
I have gotten it to work a total of about 5 times with lots of not working in between. I think it may be a motor power sensor. The times it does run, i have no beans in it and it may work a second time, but then it will not run again.
I have contacted support, but have not heard back yet. Seems like a return. Disappointed. It seems this may be a somewhat common issue.
**Update 2:
Exchanged at the store of purchase for a new grinder. So far so good!
Got into coffee last month and have been loving the Fellow Aiden. It's just so convenient and makes a really good cup of coffee.
As one does with hobbies, especially with coffee, I got down its rabbit hole and came across the concern around plastics in coffee machines.
This prompted me to order the Hario Switch with the intention to eventually transition over to it. But here's the thing, I love the convenience factor of the Fellow Aiden. I love letting it do its thing while I clean around the kitchen or tend to some other task. And by the time I return to it, it brews me a wonderful cup of coffee. So I never really got around to the Hario Switch (which is another learning curve I'm dreading to start).
Just wondering, how do you cope with this sentiment? What are your thoughts around this?
Hello, just got my ode gen 2 delivered today. Making a bit of a funny clicking noise on first start so wanted to ensure the burrs very calibrated correct. Clicking noise gone but want to ensure the burrs are set correctly.
Does this seem correct for 1 on the dial? Not sure of the best way to show the grind size. New to this so any help is appreciated! 😀
I have nothing except a cheap pour over at home that I don't use that often. I pretty much primarily drink decaf without anything added. This machine will be in my personal office at work as that's where I drink 30-40oz a day.
I hate the Keurig we have at work and the pot makes an ok basic brew. Could've just gotten a grinder and probably been ok but I go way to deep usually.
Just got my Fellow Opus 2 few hours ago, already pulled around 5 espressos (I may have issues sleeping tonight) and I'm loving it. But there is small inconvenience that sometimes it stop grinding because it detect that the Load Bin is unlocked, sonI have to wiggle around, locking and unlocking a few times to detect that is locked and keep grinding.
Didn’t like the idea of the dispersion plate being made of plastic. I talked it over with a friend that’s an engineer and this is our first prototype. This version was in aluminum for testing purposes. We plan to make the final out of brass.
Hey all, so I took a punt on the Fellow Aiden, through an early Black Friday deal on Amazon. It arrives tomorrow, and then I’m off up to the Manchester Coffee Festival for the weekend to buy some tasty beans to run through it. Anyone have any recommendations, tips, tricks up their sleeves?
Am totally new to this sub. Joined and have not read anything so apologise in advance. Did lots of YouTube and internet searching and reviews prior to purchasing now it’s time to hear from you fine folks.
Apart from the Fellow branded filters, what are you buying in the UK that is compatible with batch brew basket and relatively economical? I can't seem to find the Melitta 8-12 white filters at a decent price.