r/E30 • u/maxytaxii • 3h ago
M42 head pitting
There’s a decent amount of pitting on the mating surface for the profile gasket that seals a coolant passage, is there a way to repair?
r/E30 • u/maxytaxii • 3h ago
There’s a decent amount of pitting on the mating surface for the profile gasket that seals a coolant passage, is there a way to repair?
r/E30 • u/Top_Bus243 • 9h ago
So I recently posted about my crank no start 87 vert,
Turns out the original seller swapped the engine with a 89 but the fuel lines were swapped. Once I swapped then the car started to run and there was white smoke (first start in 14 Years) but I couldn’t step on the Accelerator. I accepted my win and gave it a break for the weekend. Now I went to turn it on and it sounds horrible😭 it will turn over but it will have a really rough idle and then sputter and die.
It was shooting some black smoke but it wasn’t thick. And it would die quickly. I’ve cleaned the icv, checked and replaced the TPS, and I’m kinda at a stand still right now. Would love any advice or ideas! I’m trying to keep the engine so anything that would help me use the engine would be nice!
r/E30 • u/Icy_Recognition5031 • 9h ago
this sub has only seen the build at night so heres some during the day, loved brg on the e36 growing up so i put it on the e30
missing front valence i know lol
r/E30 • u/porthos1984part2 • 13h ago
r/E30 • u/Western_Giraffe396 • 18h ago
Dropped a 10mm hex nut in this hole. I’ve seen other people mentioned they have to take the oil pan out.
I’ve already drained the oil, didn’t come out. Used a thin magnet but nothing. Any advice
r/E30 • u/Opening_Educator4931 • 20h ago
Help diagnose new noise after I did a manual swap. Only make noise when rolling not at idle.
r/E30 • u/Aikamping • 21h ago
And yes, I love the Taifuns
Some high points:
Manual Transmission
Mileage - 108,277
Bought from Original Family (Mother’s car originally, eventually given to Adult Son)
Cirrus Blue with Gray interior
Interior excellent - Original crack free dash. Seats overall are good, but driver seat does have a tear on the bottom.
Garage kept - Condition reflects this
Underside has surface corrosion from NH driving, but any body or frame rust was previously taken care of by original owners.
Lots of money spent on maintenance. Approx. $15,000 spent within last 2,000 miles.
Past 2,000 Miles the following items have been done:
Front struts and mounts
Hood Strut
Rear Muffler
Rear Lower Control Arm Bushings
4-wheel alignment
Floor board repair ($4,132.55) - Looks factory, very well done.
Rear Window regulator
Front wheel bearing
Front rotors, pads, and remanufactured calipers.
Remove and replaced front brake lines
Brake fluid flush
New Water pump
New thermostat and housing
New Timing belt
New v-belts (all three)
Valve adjustment
O2 sensor
New spark plugs and wires
New distributor cap and rotor
New engine coolant temperature switch
New engine coolant temperature sensor
Rear shocks
New radiator shroud
Replaced a few cracked hoses on top of engine
Cleaned idle control valve
Tires
What still needs to be done:
Vibration at idle and sometimes while driving - Should replace engine and transmission mounts as well as guibo.
Check engine light is on. I can’t get stomp test to give me code.
Overall, this car is a bit of a unicorn. Great color, garaged most of its life, manual transmission, maintained with an open checkbook, and owned by an enthusiast family. It looks amazing from 10’, but up close you can see road wear from almost 40 years and 108,000 miles of use. With that said, it’s a great car, and far better than most E30s I have seen that have been subject to multiple owners, deferred maintenance and neglect. Great bones for a full restoration, or a really nice driver for someone who appreciates a little patina on a mostly mechanically sorted car.
Looking for opinions on what $$$ I should start this at, and where would be the best place to list. I truly don’t know the E30 market well, and prices are all over the place between BaT, Facebook, and enthusiast forums.
By the way, I have all original manuals, bottle cap wheels and dealership info from the new sale (except window sticker). I also have a folder with service and parts receipts totaling $28k going back to 2010.
r/E30 • u/ilaughforaliving • 1d ago
Got new wheels today, decided to check out how they turned and discovered both wheels turn the same way when turning one of them. The car is a 91’ 318i with the M42
r/E30 • u/XTheChosenDogeX • 1d ago
So I have a 1990 325iA and I just topped off the ATF due to a leak (Toptec 1200 mixed with at205 reseal) and now I noticed I have some rpm stutters under acceleration. Been leaking pretty significantly for 2mo before I could get to it, so it took about 1.25L
Any ideas as to what may be causing it? I believe the ATF is at the right level (hard to tell with the shitty dip stick) and I put everything to spec. The entire fuel system is new short of injectors but theyve never given me this issue prior, timing was done 2y ago and <10k miles ago, and valve lashings were done within 500 miles.
The car has always had a bit of a burbly idle since it got restored, but nothing severe. This is the first time where its stuttered under load
r/E30 • u/Mu_burrrr • 1d ago
Gooday first time poster here I was wondering if anyone's mounted ZC31S recaros in there e30 before using the stock rails and might be able to offer some tips or tricks on what route they took and how they sit in the car I'm looking for something that'll be more comfortable on longer trips
Pfa my m52 swapped facelift
r/E30 • u/ATLienGG249 • 1d ago
r/E30 • u/GMW_357i • 1d ago
Keep grinding in your builds!
r/E30 • u/Goopiestgoblin • 1d ago
What’s the best way to stop this popping out? I don’t think this part is listed on realoem. Glue it in?
I feel like I’ve seen various people leaving this disconnected and deleting it altogether.
r/E30 • u/bendsomemetal • 1d ago
Is 6k too much for a clean 1989 325i auto 2 door with a bad fuel pump?
r/E30 • u/MarcosTac0s • 1d ago
Hello everyone,
I have a 3d printer and printed bushings numerous times for my car, including rear sway bar bushings. I found a 20mm front sway bar model online but they absolutely don't fit.
I was wondering if one of you had a set of 20mm front sway bar bushings and would be willing to take some measurements for me, hole size, width, depth, distance between hole and top and bottom, etc.
I'd gladly share the print file for anyone wanting to print them using TPU once I test fit them.
r/E30 • u/SAVIOR_OMEGA • 1d ago
DIY frame repair is not for the faint of heart. This car was only $3,300 and I like doing things for cheap. Given that it already has over 300K miles with a salvage title, there's no reason to pay someone to fix it.
My rear drivers wheel arch and sill are totally gone and I need to cut them out and weld new metal in. However part of the rust is on the subframe mount and that’s where I’m jacked up on. What’s the best way to have the Car on jacks and also cut out all the rust in this corner?
r/E30 • u/Financial-Drink8073 • 2d ago
r/E30 • u/AntiqueBus99 • 2d ago
Hi. I'm replacing the parts in red in pic attached. I'm wondering if anyone knows any videos or forum posts or anything that shows how it's done?
This is for a 1985/04 e30 318i manual. The same as the diagram shows.
Thanks.
EDIT: I figured it out, thanks.
r/E30 • u/porthos1984part2 • 2d ago
Ya done fucked up, a a ron. It's snowing in Boone.