r/Cummins • u/Hawk_drvr • 5h ago
OBD2/code reader
Looking for recommendations for a code reader/clearer. Feeling overwhelmed with the amount of options on amazon so thought I would ask my people. 2018 Ram 2500 Cummins 4x4. TYIA!
r/Cummins • u/Hawk_drvr • 5h ago
Looking for recommendations for a code reader/clearer. Feeling overwhelmed with the amount of options on amazon so thought I would ask my people. 2018 Ram 2500 Cummins 4x4. TYIA!
r/Cummins • u/Postells • 19h ago
2014 Ram 2500 Mega cab. Bds front 3 inch lift coil springs. Bilstein 5100’s all the way around. Synergy dual rate 1 inch lift rear coil springs. Fox steering stabilizer. Core 4x4 drag link. Trac bar and tie rods. Super heavy duty stuff with those guys. Bad Axe gear box stabilizer. Built for Thuren or Carli sway bars. Also new kryptonite ball joints. Just not got to installing them yet. Truck ride is so so much better. Definitely worth the effort.
r/Cummins • u/Usetobeme69 • 20h ago
It’s torqued down to 185ft lbs on a 2006 dodge ram 2500. It’s a psc 6 bolt steering box I upgraded to
r/Cummins • u/Final-Associate-2882 • 1d ago
While doing my heater core I saw this hose had cracked opened and am trying to find the part but cannot seem to find the right one only 2013 and up am I going to have to just make one? Thanks
r/Cummins • u/No_Pianist_9162 • 1d ago
The ecu seems to be fine I'm just hoping it didn't fry the abs module.
r/Cummins • u/Downriver-Rat • 1d ago
Should I put 15w40 in my engine? AMSOIL says to use 5w40
r/Cummins • u/Altruistic_Sea_574 • 1d ago
Greetings, all. I have a 1998.5 Cummins 24 valve and I’m trying to track down the oil leak(s). I noticed there’s fresh fluid around and underneath the vacuum and oil pump unit. I assumed it’s the infamous gasket leak between the two pumps. However as I was looking at it, there seems to be wetness around where the power steering hoses connect to the pump on the (our) left side of the unit. I’m wondering if I am actually leaking power steering fluid from the pump, not oil. Thanks y’all.
r/Cummins • u/Joeshmoe42O • 1d ago
Looking at bd iron horn kit for my 2014 stock fuel looking into 40 overs and lift pump for future but stock fuel for awhile, wondering either s364 1.0 or 66 1.0? Going to retune with CAperformance, and what’s the difference between adding an electric BD brake vs the fleece cheetah one as I do tow every now and then, thank you
r/Cummins • u/richey15 • 3d ago
had a motor with some issues, figured it would be easier to swap in anotherone i found on marketplace for a good deal, not a to good to be true deal though.
We swapped over pretty much all of our known good parts from the old engine to the new engine. as the engine had been sitting outside, and alot of those parts un known condition, we swapped over alot of the stuff. pretty much everything except the vp44 as i didnt have the tool to pull it.
we even swapped over our known good engine harness.
we plug everything in. it cranks fine. but no sputtering nothing. Ive swapped injectors, the liftpump is less than 2 years old. it runs for 25 seconds after a bump. Ive cracked lines and bled, everything seems to be fine but it just wont sputter.
I finally bought a fuel pressure kit, tapped it to the shrader valve at the fuel filter housing. reads practically nothing when cranking, and only about 7 psi after a bump on that 25 second cooldown period.
Ok, poor pressure to the vp 44. check all the fuel lines for any gaps or anything like that. its all solid ffrom what i can tell, and i get the same reading at the vp44 shrader valve too. i would be shocked if the lift pump went bad, as it was working just fine 2 weeks ago before we pulled the motor. But poor pressure, otherwise good fuel lines that i can tell, and correct high and low pressure lines are routed too and from the gas tank.
ive also checked witha multimeterthe voltage at the pump, it reads 12.3-12.7 volts so i know thats healthy. it drops to 8 volts after 30 seconds then shuts off. i think thats expected
so poor fuel pressure from the liftpump.
good fuel lines
good voltage
replace the pump right? Well, the new pump doesnt seem to run at all after a bump? if i move the line over to the old pump, it will fire right up, new pump doesnt.
is the new pump bad? or is the new pump telling me something is fucked up and the old pump just ran regardless?
im really really stuck right now. im considering swapping the engine harness incase maybe it got fucked up will i was installing the motor but everything i can tell is fine except for this fuel pressure issue. i have no idea how to proceed. ive swapped a new lift pump, doesnt run, ive checked all the lines. no dice. old lift pump runs, but low pressure. or is there pressure maybe leaking out somewhere? where are places i should be checking for this? no fuel is dripping or spraying out anywhere?
r/Cummins • u/Final-Associate-2882 • 3d ago
Is there a plug or so I just have to do repeated flushes to get the coolant left in the block out?
r/Cummins • u/woahdamnson556 • 3d ago
Kind of new to trucking and wondering how critical it is to be changing my crank case filter on my X15 engine. Truck is a 23’ T880, original engine. Couldn’t find any recommended maintenance intervals for the crank case filter, but my local Kenworth dealership is highly recommending it.
r/Cummins • u/Consistent_Place_508 • 3d ago
I’ve got a 2002 2nd gen dodge ram 2500 auto which the t case blew up on I’m putting a used t case off of a 2000 but the new t case has pto attached to it and the old one didn’t, I need a new front driveshaft for the truck and I’m looking at just buying a brand new one off rock auto but not too sure which front driveshaft I will need to order or anything if anyone knows and could let me know would be great
r/Cummins • u/Several-Reaction5932 • 3d ago
Long story short, my dad was a diesel mechanic for 25 years. He recently passed away and this bag was stolen from his house afterwards. What tools does Cummins sell that come in a travel case like this?
r/Cummins • u/TryIcy2119 • 3d ago
Truck turns off while driving or just idling. Engine dies, dash resets, radio and headlights stay on. Today the power turned off but engine stayed on. I got the u103c-00 stored code and I know it’s the rf hub/ ignition. So far I’ve replaced crank sensor, ignition switch, and tipm. Batteries are a year old and alternator is charging at 14.2 volts.
Has anyone dealt with their truck turning off and having this code?
r/Cummins • u/wyliesdiesels • 5d ago
I've been searching for a 3rd gen (preferably 06 or 07) w/ a G56 in good or decent condition without a crap ton of miles and they just dont seem to exist on the market these days.
I do see a ton of autos, some in pristine condition with low miles. So im wondering how hard it is to swap a G56 into an auto equipped truck and how much am I looking at roughly. I am in california for pricing reference...
r/Cummins • u/JMAnonymous59 • 5d ago
truck had intermittent parasitic draw / charging issues when I bought it. fixing my lift pump ring terminal and replacing all positive wiring solved this for about 18 months.
so I was driving down the road the other day and my mm3 tuner started reading wonky ass readings like 436psi boost 700 ECT and the voltage stopped charging.
batteries are good. alternator was bench tested and it’s good. alternator wiring is good and fusible link also good.
at this point I either have a broken or chafed wire in the 2 pin connector either at the ground or the wire to the ECM.
If not it’s the ECM and I just go forward with external voltage regulator + CEL bypass and ensure it’s wired to a key on/off power source in the fuse box right?
r/Cummins • u/[deleted] • 5d ago
I have a 2005 ram 2500 5.9l Cummins, in the future I plan on getting bigger injectors, turbo, built trans, right now just looking for a little more power tow/economy tune or something, have been looking at different tuners, I want to stay on a budget with a tuner because of the fact when I do the injectors and stuff I’m going to have it tuned for that so just something in the current time that will be safe and keep egts in a lower range, I hear the bully dog is bad about causing high egts but I’m not sure currently looking at the banks automind 2, just in general with a good reputation and good price what do you think?
r/Cummins • u/flapito • 5d ago
Got a P2609 code on my 2018 Ram 2500 6.7 Cummins after using remote start on a cold morning (40s). Truck starts and runs perfectly fine.
Had the Banks Monster-Ram installed back in January with the grid heater upgrade. First time getting this code since the install.
Checked battery voltage, charging system, relay, and wiring. Nothing obvious so far.
Anyone running the Banks setup ever get this code? Curious what ended up being the fix. Also wondering if the cold weather or remote start had anything to do with it.