Hopefully this info will help someone. I've been dinking around with this B4U Android based head unit (B0F8H9YV59). I bought it back in March of 2026 and yanked it out of my car by the end of July. It looks nice and mostly worked. The major issue with it is that the mic gain/sensitivity is way too low. I even hooked up my SM58 as an external mic and it's volume matched the internal mic. I don't like to particularly take calls while driving so it wasn't a deal-breaker, but using it for Google Assistant also suffered because of that. The deal-breaker was that by the middle of July, it was rebooting on it's own, way too often. So out it went and I picked up a SJoyBring (B0CT5P32L7) stereo/display that has worked relatively well.
I set the B4U unit on a shelf in my basement and forgot about it. I knew what risk I ran picking it up, so I wasn't that upset. Anyway, a week or so ago I saw some posts about folks pointing Claude at it and de-crapifying their units. So I decided to take a look at it and see if I could do a couple of things:
Debloat the device with hopes it would stabilize for normal usage
Improve microphone volume so that hands-free operation would be feasible (without yelling at my stereo)
So, not really knowing where to start, I dove into setting up LM-Studio on my computer, stumbled my way into setting up Cline in VSCode and connecting it to the model server hosted on LM-Studio. Then I would use Co-Pilot to help me form prompts. Yes, sounds pretty dumb.
According to the Amazon listing, this thing has 4GB RAM, an 8 core CPU, 64GB of storage, Android 13.
I wasted a bunch of time trying to get a Cline/AI diagnostic going. So I ditched that after a couple of evenings. I ended up using co-pilot for some advice at getting information and analyzing data.
I went over to this site https://s.xygala.com/login and used these credentials (xyauto:6823DK) to sign in and pull USB OTA images- which I ended up not needing- except to rescue myself from myself.
First, see what the actual hardware is. I installed "Device Info HW" and pulled some info:
Devicealps B9320B
Resolution 720x1280
Platform 8238
Android 13?
RAM 4GB
Flash Sandisk DA4064 64GB
CPU 8238 - armv71 4 cores
But some of those things were suspect, so I asked co-pilot for some commands to get a second opinion:
Where I ran into a roadblock - ADB access.
I needed to go into the Factory Settings, enter 8888 to access it, scroll down to USB settings and make sure that USB mode was set as 'device'.
I can't confirm this, but I read that you had to use a 4 pin USB header for ADB access - not the 6 pin. My 4 pin connector did not have a female USB-A connector - that was on the 6 pin connector; rather the 4 pin had a connector for my car. So I carefully pulled the pins from both connectors and moved the female USB A cable to the 4 pin.
I then needed a USB A to USB A cable to connect to my computer. I kept seeing online that you couldn't just splice the matching wires - that you had to take one cable and solder the ends to the "donor" USB A connector.
I just spliced the wires and it worked. Plugged things in, had to install some Android drivers and I was in business. But not only in business, but after running 'adb shell', I ran 'su' and had root. So that was a pretty nice break. So I got down to business getting info:
Platform: AC8227L
CPU Architecture: ARMv7 (32-bit)
CPU Cores: 4
RAM: 4 GB
Storage: 64 GB eMMC (confirmed)
Reported Android Version: 10.0
SDK Level: 27 (Android 8.1)
Security Patch: 2020-02-01
So, not Android 13, but Android 10, but not really as it's running sdk 27 - Android 8.1. I confirmed this again after attempting to install an .apk that required Android 9 as minimum and it failed. The CPU is a quad core - not and 8 core.
I haven't confirmed the storage by copying 40GB of data to it, but if I do, I'll post about it. yup, 64GB - or at least close enough.
I spent a few nights figuring things out, mainly looking for passwords in various apk's pulled from the device but here's the good stuff:
Accessing Engineer Mode:
I think this is where I can eventually increase the mic vol. If I use the built in Sound Recorder app, I've seen slight mic vol increases by adjusting this setting: EngineerMode > Hardware Testing > Audio > Normal Mode > Type: Mic, Level: Level 4, then adjust the "Value" my default is 192. Increasing to 255 barely does anything- even using an external mic.
If you try to open this from Factory Settings/USB Settings, it will throw a message saying you can't access it. Run this command via ADB to clear that message and access Engineer Mode: adb shell settings put global development_settings_enabled 1
Production Management
Not much here- Uses the same login as the website. Maybe an alternative for upgrading/updating.
USER:PASSWORD: xyauto:6823DK
Engineering Test Debugging
Found in Factory Settings/Parameter Setting at the bottom right
PASSWORD: 26959910
Enabling "Hidden Settings" ie. Android Developer Settings
Developer Settings is nowhere to be found. You can tap the Build section in About all you want but it won't appear.
I found this purely by accident. Still can't believe it. I just randomly tapped on the Engineering Settings header at the bottom of Factory Settings/Parameter Settings and up popped a password prompt. You have to tap 5 times to get this prompt. I still can't believe my dumb luck. I tried every password I could think of, every pin or password that has been posted and nothing worked. Got to work with Co-Pilot and we evaluated a couple of packages. Ended up using vdexExtractor and JADX to analyze PvCanset.vdex and found the password. I still can't believe I found it. I can't believe I'm not the only one who hardcodes passwords in their code. Ludicrous.
PASSWORD: ac92xy
Here you can enable OEM unlock and as far as I know it enabled fastboot and makes it possible (possibly) to unlock the bootloader.
I ran 'adb reboot bootloader' And got into the FASTBOOT mode. I ran 'fastboot getvar unlocked' next and got the result 'no' This command 'fastboot flashing get_unlock_ability' returned '(bootloader) unlock_ability = 16777216" Finally 'fastboot flashing unlock" and this appeared on screen:
Unlock bootloader?
If you unlock the bootloader, you will be able to install custom operating system software...
Yes (Volume Up): Unlock No (Volume Down): Do not unlock bootloader
But since there are no physical Vol+/Vol- buttons, I was out of luck- I think there are some pads on the pcb that i can try to solder wires/buttons to and try later.
I threw StrataOS on it and may eventually look around for packages/processes to remove.
These are pretty crap head units. I actually bought two more for my kids cars, but returned them before 30 days were up. Too late to return mine though- but thankfully mine started acting up in time. If I can get the mic to behave and get it working stable, it might go back into my Camry. Anyway, hope this helps someone in the future.
https://imgur.com/a/b4u-android-auto-head-unit-4D4KEF1