Hey guys, So for the past few months, I've been working a lot on my autonomous fire extinguishing drone. It is called Sentinel. I've been making it for my school exhibition and competition. And so this is my journey basically. I'll give you a small generated summary of my drone, and then I'll tell you what went wrong and how I improvised and how I'll improve version 2.
SENTINEL is an autonomous firefighting drone prototype I built to explore how a small drone could detect and put out a fire without a human steering it. The idea is that the first few minutes of a fire matter most, so a drone that can spot a fire and respond straight away is useful. It runs on a 10 inch frame with 3115 motors on 6S, but right now it's a ground-tested demonstrator while I work on getting the flight version up. The system has three parts. On the drone, an ESP32 is the main brain: it drives the ESCs, reads an MLX90640 thermal camera, controls a servo that aims the nozzle, and switches a 12V water pump through a MOSFET. The fire decision is simple and reliable: when the hottest thermal pixel reaches 100°C, the drone treats it as a fire, engages, points the nozzle at the hot spot, and sprays in bursts until the heat is gone, then stops by itself. An old Galaxy A32 mounted on the drone runs my own Android app with flame detection, boxes the flame on screen, and streams live video with a sci-fi style HUD over Wi-Fi to a
second phone built into the controller. The controller is a handheld panel I built from scratch with an ESP32, a TFT display, two joysticks and a master arm switch, and it talks to the drone over ESP-NOW. It has manual control, where one stick aims the nozzle and a button fires the pump, and an autonomous mode where the drone waits and acts on its own. The arm switch is the master kill: flip it off and everything stops, and if the link drops the drone stops too.
*Alright, so here are some of the things I learned along the way while making this drone.*
● So first things first, basically this was an autonomous drone project and I've used a ESP32 and a phone for the telemetry and basically the AI autonomous part of this project, which is a really unique architecture and unique choice because usually people use a Raspberry Pi or something like that to handle telemetry/directions, but I've used a different route, and it's been pretty ah It's an interesting choice.
● Of atleast how much of research I've put into it. I haven't found anyone doing such a type of architecture exactly, I don't know if it exists or not. Using like a phone for autonomy on a drone with a esp32 using usb serial, might even be there. I'm not sure cuz not everything is on the internet.
● And then comes the main question "Was I successful or not?"
All right. So the project at this kind of scale, making something out of my room, especially having limited resources, limited financing, I would say straight answer, I'm not successful 'YET'.
● Where did I go wrong?
Well, honestly, this being my first drone project, there's not only one part which makes up a drone. There are many elements. There are many engineering sectors, especially in this kind of a autonomy drone. The software, the hardware, there's so much. There's engineering of all types. There's weight distribution, there are a lot of elements that you have to consider when you make a drone.
Again this being my first time, obviously I'm not a professional, I'm not very well experienced, So yeah, it did not go as planned, but as i said I'm not done with it yet.
● So this project right now is still in development. I will continue working on inshallah.
● What happen to the drone?
Basically, the thing was the night before my competition. Like the ESC (Electronic speed controller), which was a 60 ampere, had shorted out unfortunately.
Obviously I couldn't find a ESC or a flight controller in that span of time especially where i lived. It was like the night before, literally a night before my competition.
● Why did it happen?
Basically what had happened, during my test flight that night, when I tried to throttle down, it just went completely nuts. It rolled and it completely shut off. The battery flew off, and it just crashed basically on its own.
Later I found out that the ESC I was using was a really cheap one from China, and I should have been using a proper branded ESC which i could rely on especially when making a 10-inch 6S drone.
So you could say it's also my fault that my part selection was poor. Another reason could be mechanical torque overriding the provided torque but im not sure if it hit smtg or not.
After returning home after the crash, I checked the voltage from the esc to the flight controlller and it was 22.5v 💔.
Its supposed to be 5v btw, so im guessing one of the capacitors also shorted out and gave 22v directly to the Flight controller mid flight which messed with it.
Obviously the blame is 50-50, I purchased a cheap ESC and thats smtg I shouldn't have cheaped out on really.
● What did i do on competition day and how i improvised?
So obviously now the competition was basically a day after, and after my crash, i was really heartbroken and devastated as hell bro. I was so depressed. But then I pulled myself back together, and I thought of a plan that either way I wouldn't be able to fly the drone inside of my classroom where the exhibition was taking place, because such a big drone inside a classroom is not safe either way to fly. So I made up a whole story about my drone actually working, and I sort of lied to them that my drone did fly. I mean, to be honest, it did fly for a small span of time, but then obviously it couldn't fly anymore, but I didn't let the judges know that. And so I had to show some working part to them. So I finished the fire extinguishing using water autonomous part, I finished the whole software part that night. And what I had done is, one thing i noticed that the ESC, which shorted out, still worked surprisingly after the short. I discovered this after I unplugged the flight controller from the ESC. And the ESC was still working. It's just that the voltage and ground pin was supplying 22.5 volts to the FC, and that was shorting the fc n catching on. So after removing the FC, the plan I had in my mind was that I directly wired the signal pads from the ESC, directly to the ESP32 which I had in the back. So my ESP32 was basically handling everything now. And I didn't fly it using the ESP32, but I was just using PWM for arming the drone to show that the motors spin and plus with the shooting extinguishing autonomous part. So it was a decent demonstration, I mean that's the max I could do at that moment.
So that's what I came up with, and thankfully it all of it worked out in the end ig beacuse I came first place regardless.
● So yeah, that's that.
And inshallah, I'll be releasing version version 2 in December. I'm not finished on this. I want it to fly properly. because that's what makes a drone right. Really unfortunate event tho, you know last minute, it died on me. But I mean, what's life without surprises, right, and it worked out in the end so its all good
● Inshallah, I'll work on it more and release the final movie edit which ill be making about my journey on this drone and the final version 2. The video will be releasing on dec end mostly on my Instagram acc @bur1hxn u can follow me there to watch it
Yeah so that's my story
Ill attach a few photos of the drone and the custom control panel i made as well as my journey along the way of making the drone
If anyone has suggestion or advices for v2 feel free to comment or dm me