r/radon • • Jan 23 '26

So cold out (-20F), radon is freezing

Post image
255 Upvotes

🤣


r/radon • • Mar 12 '26

We had this radon system installed in late January but I read online today that the exhaust should go above the roof and 10 feet away from windows. Should we contact the company about it?

Post image
154 Upvotes

It was put in our sump pump and they also kept the original lid on it and not a sealed lid.


r/radon • • Feb 09 '26

How did I do?

Post image
128 Upvotes

DIY crawlspace encapsulation: It's definitely not perfect and lines aren't as straight as a pro would have done. But people in my area were quoting 8k+ for encapsulation + system. So I had no choice but to do it myself.

You can see the intake pvc under the plastic lol oops i didn't dig the trench deep enough. The vertical black pipe is where I'm gonna route the air out and to the fan outside. 90% done...

My levels were reading 6-12 each day. Fingers crossed it drops in the next few days.


r/radon • • Oct 12 '24

On the Hunt for the Most Accurate Radon Detector. Sharing my research and want to learn more from you.

124 Upvotes

Hi there, I was in the market for a radon detector and did a bunch of research which I want to share. I was interested to know which model is the most Accurate. Some say that almost all consumer radon detectors should be accurate enough, but based on what I've read and through reading certain people's opinions online, it looks like there's serious questions about the continued accuracy of such devices over the longer term (say 2 years+). Many people have complained having inaccurate readings of their consumer radon detectors from AirThings for instance.

I know there's consumer and pro versions of radon detectors. The big players in the consumer space are reputable are AirThings and Ecosense and then you have companies that develop PRO products like SunRadon (but may not exclusively be just them).

My Research:

  • In the US there's the National Radon Proficiency Program (NRPP) that seems to be an established body/organization that acts as an authoritative source for radon awareness and information. They have a number of approved devices here: https://nrpp.info/devices/approved-devices/

  • What I found most interesting though, is that the Canadian arm of the organization (C-NRPP), did a test of a number of consumer grade electronic radon monitors here and presented there findings here: https://c-nrpp.ca/wp-content/uploads/2023/10/Digital-Device-Report-Oct-2023.pdf . In this link, click on "Details of the test can be found here" link further down on page 1.

  • I've shared a screenshot of the report's findings and the report is from Oct 2023, but is fairly recent. Based on the comparisons of AirThings, Ecosense and SunRadon (Consumer versions), it looks like the Ecosense products comes out on top.

Here's a slide deck from C-NRPP which explains their methodology for testing - https://radiationsafety.ca/wp-content/uploads/2023/12/Consumer-Radon-Detectors.pdf

I also found a scientific article comparing the accuracy of some consumer radon monitors which compared the performance of five different models from AirThings, Ecosense and Safety Siren in various simulated Canadian home environments: https://iopscience.iop.org/article/10.1088/1361-6498/ab96d6/pdf . Now this study looks at other models.

It looks like the cheaper AirThings Corentium Home was MORE accurate then the more advanced AirThings versions!

Questions for Discussion:

  • Seems like the Ecosense products (EcoQube and RadonEye) look like they are the most accurate of the consumer radon detectors based on my research. Does anyone have any research suggesting that others would be more accurate? I'd never heard of this company before all of this. What are your views of the accuracy of Ecosense products over time (2 years+)?

  • Seems like the SunRadon Luft has an interesting design because its plugged into a wall outlet which is unique amoung the other offerings. Has anyone used this one and what are your views on this product's accuracy over time?

  • The reason I'm not looking at PRO models is because they are very expensive ($700+) so they dont seem practical to want to purchase, and from what I've read it seems like the big difference between PRO and consumer versions is that the pro versions have sensors to detect tampering of the radon detector and its important for pros to know if a detector has moved from the place it was initially placed because it has implications for say house closings, or warranty, etc.

  • It seems like the AirThings advanced models are not as accurate as the cheaper Corentium. Two studies are corroborating this, so why are people buying/vouching for the higher end models if they're less accurate? Just because of other sensors? I dont understand the logic.

CC: u/jljim u/snowjim u/Phlojonaut u/silentcabose u/Amazing_Strength_291 u/master0909 u/MightyNonimous I've copied you all either due to providing substantial discussion in the past, being a subject matter expert, or having similarly related questions in this area.


r/radon • • Dec 29 '25

83 million Americans exposed to radon

Thumbnail
hsph.harvard.edu
109 Upvotes

Quoting the article: "The study found that nearly 25% of the U.S. population—more than 83 million people—may be exposed to radon concentrations at or above 148 Bq/m3, which are considered dangerous.Ā "

Question for anyone out there. Wouldn't this mean that the risk is even lower than thought before? The number I've seen quoted for annual radon deaths in the US is 21,000. That equates to 0.025% of the exposed population, using the 83 million number. That seems to be within the margin of error and could easily be caused by other issues like air quality it seems to me. Just trying to wrap my head around this topic.


r/radon • • Jan 24 '26

DIY mitigation worked

Thumbnail
gallery
104 Upvotes

I have been monitoring the radon level in our home for the past year. The levels were averaging 250 Bq/m3 but would spike over 500 Bq/m at times. The house is a 1970 2 storey with block foundation and a fully finished basement. It's located on a site with lots of rock. (Niagara escarpment). The sump pit did not have a cover so I decided to spend $600 and purchased a Jackel sump dome with a Fantech Rn2 and all the accessories required. The installation only took a few hours. I'm in Canada so the fan is indoors and discharges out the side wall. My expectations were low since I would not be able to do any sealing of cracks etc., but after a week the radon levels are down to below 5 Bq/m. I am very happy with the result.


r/radon • • Jun 27 '25

My DIY Radon Mitigation

Thumbnail
gallery
96 Upvotes

My radon levels were consistently in the 4 pCi/L. They were elevated for a few days while I had a hole in my floor. Now that I work full time in the basement, I wanted to lower this number but I wasn’t willing to pay $2k US. I completed the system for just under $1k. Renting the core drill was my biggest expense at $240 (for 21 minutes of shear anxiety). I spent another $60 in tools. I originally hoped to complete it for $500. After 4 days, I am confident that my level is ~1. My roof is 2 stories up at this location, so I am debating just leaving it as is for now even though I have 2 20’ pipes waiting to be installed. I appreciate the contributors in this subreddit. Thank you giving me the courage to undertake this project.


r/radon • • Jun 03 '25

My DIY radon mitigation: From 18 pCi/L to non-detect

Thumbnail
gallery
93 Upvotes

I just got results back after my DIY radon mitigation installation. Below detection limit! Feeling pretty good about it.

I bought this house in September. Skipped radon testing in the inspection phase because of how much competition we faced for the house. I expected high radon based on the area and knew I wasn't going to make demands or back out of the deal over a $2k fix.

My original test in March found 18 pCi/L. No great, not terrible. I got a few professional quotes that ranged between $1500-$2000 depending whether I wanted to go through the roof or out the exterior wall. After watching a handful of YouTube videos I decided this is a pretty simple job that I could DIY. Basement footprint is ~1600 sq ft, and all sources I could find said a single point of mitigation would be sufficient.

I spent a fair amount of time planning the job. Made some crude drawings. Estimated PVC needs. Read up on electrical and how to drill through concrete. I bought my fan and most of the non-piping supplies through Healthy Air Solutions and highly recommend their website for the DIYer.

First was determining the fan and sizing pipe. I opted for the RadonAway RP145 fan which is compatible with 3" or 4" piping. I opted for 4". It costs more, but I'm already going to the effort to mitigate, why not maximize the fan's capabilities? Also, you can get the pro model through Healthy Air Solutions which supposedly is more resistant to fading/discoloration.

For electrical, I tied into an existing outlet that's on its own 20A circuit. I used 14/2 Romex, though someone has pointed out to me this is incorrect for 20A so I'll be remediating that. I ran the wire through the siding and hooked it up to an exterior switch and then ran wire through 3' of conduit to the fan.

Concrete drilling wasn't totally awful but was by far the hardest part of project. I opted to hammer drill using this method. I decided to buy instead of rent since I expect to need it down the road. This $76 SDS drill from Lowes did great. The included 1/2" bit and chisel made going through the foundation floor a piece of cake. I bought an additional 12" x 3/4" bit to get through the 8" exterior wall.

The exterior wall was by far the biggest PITA to this project. 8" concrete is no joke. The drill did fine but I had a hard time not jamming the chisel. And then I spent more time getting the slope right for the horizontal pipe run. About 4 hrs of drilling and chiseling. Not fun, especially in PPE. If you can go through the siding, it's 10x's easier, but that just wasn't an option from my mechanical room.

I filled 2 5-gallon buckets with gravel from under the foundation. I was really happy to find how much gravel was down there. I went fairly deep and never hit dirt. Made me feel more confident a single fan would move enough air.

From there, it was just a series of measuring/cutting/glueing pipe from the hole to exterior. Sealing the foundation hole. Installing the fan and wiring it up. Then running the pipe up to the roof and anchoring it to the siding. There's a screen up top to keep critters out.

Finally, I wanted the exterior pipe to be as unobtrusive as possible. Sherwin Williams sold me some very expensive primer and paint they said would adhere to PVC and hold up to sun. It took a couple of coats of each, but I'm pretty happy with how it turned out. I might add a shrub to hide the fan but don't feel it's a necessity.

I still need to patch up the exterior wall a bit, but as someone else told me, "It's a foundation wall. Nobody cares." So it's fallen down my priorities. I sealed up the gaps with spray foam and called it good for now.

All-in cost:

- $288 for the fan & kit/exterior switch/conduit/mounts/top cap

- $210 PVC pipe (2 x 10ft) and 10 x 45s/90s ($13.60 per elbow sure seems excessive)

- $80 hammer drill

- $25 drill bit

- $25 wiring

- $30 miscellaneous (expanding foam, crimpers, etc)

- $70 paint and primer

TOTAL = $728

TOTAL COST SAVINGS (vs. lowest exterior estimate): $772

Was it worth it? To me, yes. To a lot of people, probably not. I spent a full weekend installing this, and there were parts that really weren't fun. But I get a lot of satisfaction out of DIY'ing shit, so yeah, I'd do it again. And not having to go through the exterior foundation wall would move it solidly into "worth it" territory for a lot more people, imho.


r/radon • • Dec 07 '25

Bought a house recently, is this normal?

Post image
66 Upvotes

r/radon • • May 01 '25

So, uh… how long do I have to live?

Post image
64 Upvotes

Just got this and it's practically off the charts. I've been living here a year already šŸ˜…


r/radon • • Feb 01 '23 Silver is Forever

My DIY Radon Mitigation

63 Upvotes

Pictures: https://imgur.com/a/uXZhevE

I have found the subject of radon to be frustratingly difficult to research because the radon mitigation industry has flooded the internet with what I'll call "advermation." Websites that purport to teach you about radon and radon mitigation but which really are just ads for their mitigation service. They usually contain intimidating language like "there's no safe amount of radon," and "you could make your radon problem worse by trying to do it yourself!"

I put this together to summarize everything I learned researching DIY radon mitigation.

Do you need mitigation? A cost-benefit analysis.

It doesn't help that official sources are wishy-washy on when abatement is necessary at levels below 4.0 pCi/L; though they are clear you should mitigate with levels greater than 4.0 pCi/L. But even then, whether mitigation is necessary is a question for you based on your exposure (e.g., is it only in your basement? How much time do you spend there?) and risk tolerance. Bear in mind that while it's true that there's no totally safe level of radon, there's also no totally safe car ride (crashes), day at the beach (skin cancer, drowning, great white attack), or even just a stroll down a palm-tree studded boulevard (falling coconuts kill more people than sharks! (allegedly)). Everything carries some risk.

It's also helpful to understand the mechanism of lung cancer with radon exposure. Exposure doesn't "build up" over time, like arterial plaque with heart disease. Each single alpha particle emitted by radon could cause cancer if it strikes you in a particularly unlucky way and your body is unable to repair the damage. The odds of this happening with a single alpha particle are infinitesimally small; but the more alpha particles you expose yourself to, the more chances for that one-in-a-million shot to occur. The EPA has info showing likelihood of cancer based on full-time exposure to radon (i.e., not just what you have in your basement) at different levels. https://www.epa.gov/radon/health-risk-radon.

Other things to consider:

  • Cost (DIY: ~$500 pro: ~$1,500. Also, about $60/yr in electricity to operate)

  • Appearance (can the radon pipe be installed discreetly, or will it be an eyesore on the outside of your house?)

  • Difficulty of an interior pipe run (do you have a plumbing wall or closet available to run the pipe?)

In my case my house came in during a pre-purchase radon test at 3.2 pCi/L. My house is built into a hill, so my entry level is half below-ground. I didn't spend much time on that floor, so I didn't mitigate. But then I started working from home full-time down there, so I bought an Airthings digital meter and found my long term average was 4.24 pCi/L. This is high-ish, but considering that many homes in coal country have double-digit radon numbers, it's really not that high (to me, anyway). I decided to mitigate only after I spent a LOT of time figuring out a pipe route that would be concealed and vent through the roof. I probably would not have mitigated if I had to do an external installation, but your cost/benefit analysis might have varied; it's wholly subjective.

Step 1: Planning Pipe Route

A typical pipe run will start about a foot away from a foundation wall in your basement, and must terminate above your roofline, 10 feet away from any windows. You can run the pipe outside or inside. Outside options range from unembellished PVC drain pipe to downspout pipe, which blends in a little better. Also, with the outdoor installation option, your radon fan will be mounted on the side of your house--the fan cannot be installed in a living space, including an unfinished basement, in case of a leak. Aesthetic concerns aside, this option is the easiest, as you won't have to tear open any walls or try to snake a pipe through a closet or some other unused corner of your house.

The other option is indoors. Many pros will run the pipe from the basement through a closet to the roof. You can also frame it in and drywall around it. Or you can look for water walls-- walls in which your home's plumbing is routed and which will be thicker than a standard wall, and will run from the basement up to the attic.

You can use 3" or 4" diameter PVC pipe with most radon fans. Obviously, if your radon problem is serious, you'll want to use the 4" pipe to maximize volume of air being moved, but a 4" pipe has an outer diameter of 4.5", making it harder to fit inside walls. A 3" pipe has an outer diameter of 3.5", exactly the width of standard wall framing, however, the fittings (90 degree bends, couplings, etc.) add another 1/2" of thickness, making it impossible to enclose in a standard wall unless you're able to get the pipe in the wall without any fittings (even if you can, you can't cut the top and bottom framing members of load-bearing walls).

Step 2: Cutting the basement slab for the suction pit

The pipe run begins in the suction pit unless you're going to use your sump pit, which is also an option. You will cut a hole in your basement slab near a foundation wall, but at least 1 foot away from it so as to avoid hitting a footer. To do this, I used a 4 1/4" diamond hole saw I bought on Amazon for $85 Link. (You'll also need to buy an arbor for it.) I just happened to use that size because it would accommodate 3" pipe and I already owned it from another project, but you'll want at least a 4 3/4" for 4" pipe. Use or rent a heavy-duty drill, and do not use the hammer setting. Or you can do like I did and use a regular cordless drill and just go slowly so as not to burn out your drill (it took me about an hour with my 4" slab) and keep the cutting surface wet. Note: a typical slab is 4" to 6" thick, and can be as thick as 8", so you want to make sure your bit is long enough. If you're doing an outdoor pipe run, the hole saw can be useful in cutting through exterior brick as well if needed. If you don't want to buy a hole saw, you can make a messier, but still effective, hole by drilling several 3/8" holes with a hammer drill in a circle large enough to accommodate your pipe, then using a hammer and chisel to knock it out.

Step 3: Digging the suction pit

You'll need to scoop out at least 5 gallons of dirt from the hole to give the radon a place to accumulate. If you have "tight" soil, like clay (as opposed to "loose" soil like sand), or very high radon numbers, you can remove more. 5 gallons worked just fine for me, despite tight clay soil. You can always dig out more later if you need to. Pros will use an auger to dig. I just used a pry bar to loosen the dirt and scooped it out with my hands. The 4.25" hole was not too small for my hand, and it took about an hour to fill a 5 gallon bucket.

You might have to dig multiple pits if you have a large slab, tight soil, or high radon numbers. Pros will drill test holes and measure how well the suction travels under the slab to figure this out in advance. But you can use trial and error. Start with one pit. That will cover all but the most difficult cases. Add more later (or get a more powerful fan) if you're not seeing results.

Step 4: Sealing the Foundation

In order to make sure your fan is pulling air from under the slab and not conditioned air from your basement, you'll want to seal all of the cracks you can in your slab, especially those closest to the suction pit, as well as the perimeter where your slab meets your foundation wall. Polyurethane concrete sealant is the way to go. It's applied from a caulk gun. Beware, it takes 7 days to fully cure and remains tacky for a few days. Skip the self-leveling stuff, it's too messy.

Step 5: Running the pipe

If running your pipe indoors, you can (and code may require) that you fill gaps around pipe penetrations between floors with fire-blocking foam (Great Stuff makes a product). There is also a fire-blocking collar required when going between the garage and the house. If you're doing an indoor run, your pipe will be mostly vertical, so you'll need to make sure it's supported. Use riser clamps from a plumbing store (box stores don't carry these in my experience) between floors to hold the vertical runs of pipe up. Also make sure to maintain standard draining slope of 1:4 on horizontal runs. Soil is relatively warm and damp. The air outside and in your attic can be cold. This will cause condensation and it needs to be able to drain back into the ground. (I saw abundant condensation in my pipe in the attic with temps around 50 degrees before I even connected the fan, just from passive airflow).

On the basement end, you'll want to end your pipe in the suction pit, about 1" below the bottom of your slab. You can fill the gap around the pipe with foam backer rod and polyurethane concrete sealant or hydraulic cement.

Buy and install a manometer (a U-tube) on the pipe in the basement. It confirms negative pressure in the pipe so you know your fan is working.

Step 6: Roof penetration

If you're doing an interior pipe run you'll install a roof boot for the pipe to go through the roof (also called pipe flashing). My box store sold a plastic version and a metal version. I read that the plastic can crack and come detached, and that metal is preferred. I found this video tremendously helpful-- it taught me everything I needed to know. I spray painted the aluminum flat black to blend in with the shingles before installing it.

Step 7: Installing the Fan

Based on advice I got from this sub, I went with the Swiss Army knife of fans, the Festa Maverick ($160 shipped) (comparable, but with slightly better performance than the ubiquitous, but equally suitable Radonaway RP-145, $140 with free delivery to box store). Order your U-tube with the fan-- I forgot mine and they were going to charge $18 shipping on a $8 tube so I ended up ordering another brand. There are higher-power fans for larger slabs and tighter soil, but they consume more power and may be more audible. Again, I'd start small here, and upgrade only if you're not seeing results. You'll use rubber Fernco pipe connectors to connect the pipe to the top and bottom of the fan, which minimizes vibration transfer, and makes the fan easily removable. As far as supporting the fan itself, every installation I saw online did not have any independent support for the fan itself. It just sits on top of the pipe. Make sure though that your pipe is properly supported near the fan. You'll want to run a circuit to the fan, or tap one in your attic if it's readily available to power the fan. It can be hardwired, or you can connect a power cord to the fan and plug it in to an outlet. I bought a generic power cord and went that route so that it could be easily removed if needed.

Results: my radon average went from 4.24 pCi/L to < 0.5 pCi/L. I can't hear the fan at all. It took me a weekend.

I am not an expert, and I may have gotten some things wrong here. If so, let me know and I'll edit the post.


r/radon • • Apr 12 '26

DIY project done for under 300 dollars

Post image
55 Upvotes

r/radon • • Feb 07 '26

After 3 years, I decided to mitigate (Canada)

Thumbnail
gallery
53 Upvotes

I've been running an Airthings View Radon for 3 years. While the yearly average was ~140Bq/m3, I noticed a cycle that occurs in the fall, Sept-Jan, where levels would spike upwards of 300-400 for months.

What's unusual is that the levels would often be worse upstairs on the second floor during this period, where the bedrooms are.

At first I thought the detector was malfunctioning so I purchased traditional radon test kits, short term and long term, and ran them. I did 2 rounds of the long term (2 full years), and all of the data showed the sensor was mostly correct (although it does read slightly higher).

This year I finally had enough data and concluded the risk was high enough I should mitigate, especially since I WFH 100% and also spend considerable time in the basement (home gym).

The system is working well, very quiet, and my average for the last 2 days has been ~20Bq/m3.

This is in the GTA area.


r/radon • • Feb 15 '26

Thanks for the advice

Thumbnail
gallery
51 Upvotes

Took a lot of your advice and made the switch from aluminum to schedule 40 pvc . I just couldn’t live with the fact that someone did this wrong and it was okay. I had to make it right. I don’t think it came out bad at all

See before and after


r/radon • • Mar 12 '26

Radon success story

Post image
50 Upvotes

My 1952 ranch was reading as high as 17 using a Radon Eye I purchased. I felt forced to investigate ways to lower this. First try was purchasing a sealed lid for the sump pit but it didn't do anything.

So I broke down and called a local professional to come out and he told me what he needed to do.

  1. Seal all floor cracks in concrete basement floor.

  2. Encapsulate with sheet plastic the small connected crawl space under a converted porch to bedroom. He told me crawls are the biggest sources of radon.

  3. Cover and seal 2nd sump pit.

  4. Punch 3 holes in concrete floor and add PVC pipe and fan to suck air out of house with fan.

Encapsulating the crawl doubled my bill. I paid 4k total when it could have been 2k.

But I couldnt be happier with the results. First reading post work was <4. Then the next two days were <2 and today I had .3!

Im just really really happy with the result. I spent 250 extra for black piping instead of ugly white PVC. It blends in with my gutter downspouts.


r/radon • • Dec 24 '25

DIY Success Story

Thumbnail
gallery
48 Upvotes

Hi everyone. I want to share my success with my DIY radon mitigation system. I have no expertise in this field, and just attempted this after doing some research on YouTube, Reddit and other sites. This is not a professional recommendation, just an explanation of my set up that might help others.

I am in the Midwest in a ranch house built in 1960. After living here for 5 years I finally tested my radon and had levels around 30 pCi/L.

I reached out to a few companies and was frustrated with the cost— $2100. I was also annoyed with one company in particular who seemed more interested in telling me how dangerous radon is and trying to schedule me as soon as possible… no guarantees on the efficacy of their system and very little explanation of why it cost so much.

I have an existing sump pit that has drainage tile entering it. I used the Jackel sump pit cover and plenty of silicone to seal it against the uneven floor. Drilling the 12 holes into the floor was slow going with my 20v Dewalt hammer drill, but it did the job.

To vent to the exterior, I needed to drill a 3.5ā€ hole through the brick facade. This was far and away the most stressful part, and it took forever using a $20 masonry hole saw bit from Amazon, and a Harbor Freight SDS rotary hammer drill. It took a few evenings with a headlamp to finally get all the way through. I had some leeway between the floor joists, so my hole didn’t need to be dead nuts. If you are not up for that challenge, you can rent much beefier drills/bits or find a local professional to drill your hole.

After that, I simply followed the instructions for the Jackel cover, and rigged up my PVC and fan. I installed it indoors as a proof of concept, and so I wouldn’t have to spend even more time figuring out how to manage condensation and freezing conditions outside. I plan to move the unit outside and get it routed above my roof in the spring.

I installed a Festa AMG Maverick with the 3ā€ couplings. Installing this was very easy, and I had no issues with that at all. I purchased the kit to avoid overthinking the necessary components. I did not spend too much time agonizing over the right fan, and just went by some general guidelines on where to start. I did not get a pressure test done, and I basically just picked a fan and rolled with it. I don’t even really know what material my foundation is sitting on.

I installed everything without PVC cement, just to see how it performed and to make adjustments as needed. Initially, my numbers dropped to about 9 pCi/L. Not good enough.

So I looked at the beaver system surrounding the walls of my foundation, and filled the top of the gap with expanding foam. I used the window and door foam so it wouldn’t push the beaver system too far out. (See in pictures)

After this, my numbers dropped to about 2 pCi/L and my long-term average is 2.12. It’s been about 2 weeks from the installation, and I’ve been as low as .8 pCi/L and as high as 3.0. This is in the winter with temps and pressure fluctuating with snow storms.

As far as I can tell, this system is doing the job. I saved myself about $1600. I have $220 in the fan/kit, $120 in the Jackel cover, and another $150 ish in the PVC, silicone, drill bits, Tapcons, etc.

I expect my numbers will also decrease as I cement the PVC in place to remove all the potential leaks in the system. I am monitoring my numbers frequently, so for now I’m not concerned about the fan being installed in the basement. Once it’s all cemented, I really think I could just leave it where it’s at and not even bother with an exterior installation. I know that’s not best practice, but it’s really hard to see how it could go wrong. The fan is super quiet and just makes a light whirring noise.

Anyway, I hope this information helps someone who wants to just give it a shot. I think the biggest challenges are:

  1. Knowing which fan to buy

  2. Drilling into exterior of foundation

  3. Acquiring all the tools

And certainly the biggest risk is: what if my numbers don’t drop to a safe level? I lucked out that this system just works really well, but I could potentially have been out my $500 and having to call up a professional. Luckily, that’s not the case, and either way I was comfortable assuming that risk. I am very happy to give an ā€œF youā€ to that company that wanted $2100 for the same system.

Feel free to comment with questions, and also suggestions. I’m not 100% done, so if anyone sees something I did wrong, let me know. Thanks to this community for all the posts, comments, and knowledge!


r/radon • • 10d ago

Cost of professional radon mitigation installation is ridiculous.

47 Upvotes

Three years agoI had radon mitigation installed on my 1500 square-foot home. The cost at that time was $2300. That obviously included the tubing, the 12 mil membrane, and the exhaust fan with the PVC pipe running up through the roof.

Just a couple of months ago we finished up a 12ā€˜ x 14ā€˜ addition on the corner of the house. I got with the radon mitigation installer from a few years ago to have him extend the mitigation to the area of the addition. He quoted me $980. I felt that was outrageous given how I paid only slightly more than double that to have the entire house done a few years ago. Of course, he gave me all the excuses about the cost of materials rising so drastically.

I accepted the quote and told him to go ahead and get it done. He stood me up on two occasions after making appointments to show up and do the work. When I would follow up with him, I would get excuses that another job ran long or that someone called out sick. I finally got tired of trying to chase him down and being ghosted.

I got with the only other somewhat local radon mitigation company and they quoted me $2450 to do the 12 x 15 addition. I laughed and told him not a chance.

I purchased all the material myself for under $150 and also a $30 4 inch concrete, boring drillbit to pass the tubing through the concrete block wall, which is between the main house and the addition. Labor wasn’t terrible and now for well under $200 all in, the job is done to a professional level quality. And I have roughly 20 feet or so of corrugated tubing left over.


r/radon • • Feb 18 '26

Landlord wont install proper radon mitigation, here's how I dropped levels from ~600 bq/m3 to under 100 for less than $60

Thumbnail
gallery
44 Upvotes

I live in a basement suite and decided to get an Ecoqube monitor which showed alarmingly high radon levels. Landlord has no interest in a proper install, so here's my solution that is cheap and extremely effective

(1) Tape up the flap on the outside dryer vent (2) $50 Vevor inline duct fan installed at the dryer vent and piped to my air purifier grille

This creates positive pressure inside the basement suite, quickly reducing radon levels to below 100 at which point the fan can be turned down to its lowest level to maintain safe radon levels by pressurizing the basement just enough to slow soil outgassing. The air purifier pre-filter catches any dryer lint from the piping

Yes it's a hassle to crawl behind the dryer and swap it over every time I need to dry clothes (could be remedied by installing an electric vent selector damper thing), but I much prefer this over having to open windows in the dead of winter for 30 mins just to put a small dent in the radon levels.

And yes this does bring in cold outside air but with the air purifier mixing it well with the indoor air, and the vent on its lowest speed, it is not noticeable and the heating barely runs more often than before


r/radon • • 8d ago

Successful self mitigation

Thumbnail
gallery
43 Upvotes

TLDR: Did a self install and brought my levels from 6.8 pCi/L to 0.8 pCi/L

I grew up in a house with a radon mitigation system on the east coast. When I moved to MI I was always surprised by the lack of mitigation systems. That's been changing over the last few years but comparatively speaking they are rare. This got me curious about my radon levels so I bought two monitors: 1 for the living space and 1 for the basement which is finished but we don't spend a lot of time down there.

The results were not great. Yearly average for the living space was 3.3 pCi/L while the basement was 6.8 pCi/L. The basement had a highest recorded value of 26 pCi/L. Yikes!

I'm naturally a DIY person and I knew an installer would just put a pipe out the side of the house and go up to the roof from the sump. That would have been ugly and it was right where we spend a lot of time as it's next to our deck. I also knew from other projects that routing a 3 or 4" pipe internally from the basement to an attic space would be challenging because of the way the floors/walls were laid out. I struggled with 1" electrical conduit on a previous project.

The plan:

Use the sump basin as my suction pit. There were corrugated drain tile into the basin and they seemed to extend for quite a bit so that seemed like a good place to start. Worst case I'd have to find another suction point. From the pit go into the basement ceiling (drop ceiling thankfully!) across the house into the garage. Up the garage wall into one of the attic areas and then out the roof.

Execution:

I used the sump cover from Jackal. It's well made and I really like having the window so I can check on the pump and level. As with any project things went sideways quickly. The sump pump that I had while still functional was old and the outer insulation on the cord disintegrated. New pump time...

Installed the new pump and the new cover. It wasn't hard to get my water powered backup pump, and sump alarms working as well. The project stalled because life got in the way. Simply sealing the sump did cause levels to drop a little it wasn't significant.

This summer I finally got back to the project and installed 3" PVC to the sump cover because that's the largest port that the Jackal supported. I transitioned to 4" shortly after that. Routed the pipe to the garage which fortunately wasn't really difficult because of the drop ceiling AND I was going with the floor joists. Once in the garage I put the radon fan on just to do a trial to see if I had any surprises...

  • I broke the 3" flange on the sump cover. I couldn't find a place to buy this but Jackal bailed me out. Their customer service folks are fantastic.

  • A floor drain apparently also went to the sump so I needed a way to seal that. I ended up using a Volcano Drain because I needed the drain to still be functional.

throw in a tube of caulk and the system seemed to be working.

I routed the pipe into the attic where I then needed to add a scuttle hole because that attic was inaccessible at the start of the project. Once in the attic I found some insulation issues and where the one bath vent terminated incorrectly. Problems for another day...

Routing the pipe through the attic was fairly easy. A quick jog around the trusses and then a straight shot to a low point on the roof away from other penetrations. I really didn't want to drill through the roof because it was only a year or two old at this point but I did it. Flashed the pipe, learned I don't want to be a roofer, and checked for leaks. I used ABS to go through the roof because the roof is black and this would hide better. This part of the roof is also towards the front of the house another reason why being lower was better.

Installed the fan, wired it to the same outlet as the garage door opener since that's a non switched circuit and it's really obvious when it doesn't work. Side effect is that this circuit is also backed up by a standby generator. Installed the manometer in the garage where I'll be able to see it daily.

Results:

Fired the system up at 11PM and waited. The next morning the levels in the living space were already below 1 pCi/L for a 24 hour period. Basement had improved drastically too. I was skeptical about the living space only because we had our windows open the previous day because it was gorgeous out.

Here we are a few days later and both the basement and living space are <1 pCi/L

Thanks to this sub I think we've got another good install.


r/radon • • May 29 '26

Since putting in our radon fan, we did it ourselves pretty easy. Hardest part was drilling through block wall

Post image
43 Upvotes

r/radon • • May 09 '25

My sister just bought this house, two pipes removing radon aren’t sealed at the floor completely and they whistle. Can I use 100% silicone to seal it up? I’m a plumber but just checking here before I do it

43 Upvotes

r/radon • • Jan 07 '25

Just wanted to share my diy install with y’all, went from 17 pCi/L to 0.4 NSFW

Thumbnail
gallery
43 Upvotes

r/radon • • 7d ago

How bad is radon actually?

41 Upvotes

For reference, I live in a state with high radon. My family did not know until I questioned it while looking for my own house. Once I found out it existed they tested the house and it was 8-9pci/l (in the winter) I had lived in the basement for like 10-15 years. Ive never had lung issues, and I fortunately stopped smoking a few years ago. I consulted my doctor and was told to call poison control since he didnt know what to do... based on what ive been told alot of the studied were done in either 3rd world countries (told by poison control) or on coal miners(told by radon mitigation guy). So im left wondering, should I even be concerned? Should I add a yearly lung scan to my calendar?

Edit: We had an appointment to get the radon mitigated. I am more or less just concerned about my health and wondering if its as scary as the internet says. After reading all the feed back, I will just have my new doctor do extra screenings as a precaution. I appreciate those who took the time to respond and I do feel better about the situation as a whole.


r/radon • • May 04 '25

My Radon DIY.

Thumbnail
gallery
41 Upvotes

Re posting since not all my photos uploaded.

Just wanted to say thanks to everyone that helped me on this reddit for my build.

I used an Amazon purchased fan, Vevor 4 - 4.5in.

No all progress photos are here but the most important ones I think.