r/pchelp • u/Obessedwithshit • 12h ago
HARDWARE I'm having this problem with my pc
I'm thinking it's either ram or the gpu
r/pchelp • u/bearssuperfan • Dec 15 '19
"No POST", "system won't boot", and "no video output" troubleshooting checklist
This checklist is a compilation of troubleshooting ideas from many forum members. It's very important to actually perform every step in the checklist if you want to effectively troubleshoot your problem.
1.Did you carefully read the motherboard owners manual?
2.Did you plug in the 4/8-pin CPU power connector located near the CPU socket? If the motherboard has 8 pins and your PSU only has 4 pins, you can use the 4-pin connector. The 4-pin connector USUALLY goes on the 4 pins located closest to the CPU. If the motherboard has an 8-pin connector with a cover over 4 pins, you can remove the cover and use an 8-pin plug if your power supply has one. This power connector provides power to the CPU. Your system has no chance of posting without this connector plugged in! Check your motherboard owners manual for more information about the CPU power connector. The CPU power connector is usually referred to as the "12v ATX" connector in the owner's manual. This is easily the most common new-builder mistake.
3.Did you install the standoffs under the motherboard? Did you place them so they all align with the screw holes in the motherboard, with no extra standoffs touching the board in the wrong place? A standoff installed in the wrong place can cause a short and prevent the system from booting.
4.Did you verify that the video card is fully seated? (may require more force than a new builder expects.)
5.Did you attach ALL the required power connector(s) to the video card? (some need two, some need none, many need one.) It is best to use cables connected directly to the PSU. Only use adapters if absolutely necessary.
6.Have you tried booting with just one stick of RAM installed? (Try each stick of RAM individually in each RAM slot.) If you can get the system to boot with a single stick of RAM, you should enable an XMP profile or manually set the RAM speed, timings, and voltage to the manufacturer's specs in the BIOS before attempting to boot with all sticks of RAM installed. If your motherboard supports XMP profiles, that is the best way to get your RAM running at its rated specs. Nearly all motherboards default to the standard RAM voltage (1.8v for DDR2, 1.5v for DDR3, & 1.2v for DDR4). If your RAM is rated to run at a voltage higher than the standard voltage, the motherboard will underclock the RAM for compatibility reasons. If you want the system to be stable and to run the RAM at its rated specs, you should either enable an XMP profile or manually set the values in the BIOS. Many boards don't supply the RAM with enough voltage when using "auto" settings which causes stability issues.
7.Did you verify that all memory modules are fully inserted? (may require more force than a new builder expects.) It's a good idea to install the RAM on the motherboard before it's in the case.
8.Did you verify in the owners manual that you're using the correct RAM slots? The following image is just an example. Verify in the owners manual the recommended RAM slots to use for single, dual, triple, or quad channel applications. This will vary depending on motherboard manufacturer, number of supported RAM channels, and how many sticks of RAM are being used.
9.Did you remove the plastic guard over the CPU socket? (this actually comes up occasionally.)
10.Did you install the CPU correctly? There will be an arrow on the CPU that needs to line up with an arrow on the motherboard CPU socket. There may also be a notch that will only line up in one direction. Be sure to pay special attention to that section of the manual!
11.Are there any bent pins on the motherboard/CPU? This especially applies if you tried to install the CPU with the plastic cover on or with the CPU facing the wrong direction.
12. If using an after market CPU cooler, did you get any thermal paste on the motherboard, CPU socket, or CPU pins? Did you use the smallest amount you could?
13.Is the CPU fan plugged in? Some motherboards will not boot without detecting that the CPU fan is plugged in to prevent burning up the CPU.
14. If using a stock cooler, was the thermal material on the base of the cooler free of foreign material, and did you remove any protective covering? If the stock cooler has push-pins, did you ensure that all four pins snapped securely into place? The easiest way to install the push-pins is outside the case sitting on a non-conductive surface like the motherboard box. Read the instructions! The push-pins have to be turned the OPPOSITE direction as the arrows for installation. This means with the arrow pointing away from the heatsink.
15. Are any loose screws laying on the motherboard, or jammed against it? Are there any wires running directly under the motherboard? You should not run wires under the motherboard since the soldered wires on the underside of the motherboard can cut into the insulation on the wires and cause a short. Some cases have space to run wires on the back side of the motherboard tray.
16. Did you ensure you discharged all static electricity before touching any of your components? Computer components are very sensitive to static electricity. It takes much less voltage than you can see or feel to damage components. You should implement some best practices to reduce the probability of damaging components. These practices should include either wearing an anti-static wrist strap or always touching a metal part of the case with the power supply installed and plugged in, but NOT turned on. You should avoid building or working on a computer on carpet. Working on a smooth surface is the best if at all possible. You should also keep fluffy the cat, children, and Fido away from computer components.
17. Did you check the debug LEDs, Q-code display, or install the system speaker (if provided) so you can check codes in the manual? Most modern motherboards come with debug LEDs or a Q-code display. A system speaker is NOT the same as normal speakers that plug into the back of the motherboard. A system speaker plugs into a header on the motherboard that's usually located near the front panel connectors. Debug LEDs, Q-code displays, or a system speaker are critical components when trying to troubleshoot system problems. You are flying blind without them. The motherboard owner's manual will have a list of codes you can reference. If your case or motherboard didn't come with debug LEDs, a Q-code display, or system speaker you can buy a system speaker for cheap here: http://www.cwc-group.com/casp.html
18. Did you read the instructions in the manual on how to properly connect the front panel plugs? (Power switch, power led, reset switch, HD activity led) Polarity does not matter with the power and reset switches. If power or drive activity LED's do not come on, reverse the connections. For troubleshooting purposes, disconnect the reset switch. If it's shorted, the machine either will not POST at all, or it will endlessly reboot.
19. Did you turn on the power supply switch located on the back of the PSU? The switch should be depressed on the side with an I, the O means off. Is the power plug on a switch? If it is, is the switch turned on? Is there a GFI circuit on the plug-in? If there is, make sure it isn't tripped. You should also make sure the power cord isn't causing the problem. Try swapping it for a known good cord if you have one available.
20. Is your CPU supported by the BIOS revision installed on your motherboard? Most motherboards will post a CPU compatibility list on their website.
21. Have you tried resetting the CMOS? The motherboard manual will have instructions for your particular board. User Darkbreeze also provided the following:
BIOS Hard reset procedure
Power off the unit, switch the PSU off and unplug the PSU cord from either the wall or the power supply.
Remove the motherboard CMOS battery for five minutes. In some cases, it may be necessary to remove the graphics card to access the CMOS battery.
During that five minutes, press the power button on the case for 30 seconds. After the five minutes are up, reinstall the CMOS battery making sure to insert it with the correct side up just as it came out.
If you had to remove the graphics card you can now reinstall it, but remember to reconnect your power cables if there were any attached to it as well as your display cable.
Now, plug the power supply cable back in, switch the PSU back on and power up the system. It should display the POST screen and the options to enter CMOS/BIOS setup. Enter the bios setup program and reconfigure the boot settings for either the Windows boot manager or for legacy systems, the drive your OS is installed on if necessary.
Save settings and exit. If the system will POST and boot then you can move forward from there including going back into the bios and configuring any other custom settings you may need to configure such as Memory XMP profile settings, custom fan profile settings or other specific settings you may have previously had configured that were wiped out by resetting the CMOS.
In some cases it may be necessary when you go into the BIOS after a reset, to load the Optimal default or Default values and then save settings, to actually get the hardware tables to reset.
http://www.spotht.com/2010/02/reset-bios-clear-cmos.html
22. If you have integrated video and a video card, try the integrated video port. Resetting the bios, can make it default back to the onboard video. If you are trying to use HDMI outputs, try using DVI or VGA instead. Sometimes, the HDMI ports won't work until the correct drivers are installed.
23. Make certain all cables and components including RAM and expansion cards are tight within their sockets.
I also wanted to add some suggestions that jsc often posts. This is a direct quote from him:
"Pull everything except the CPU and HSF. Boot. You should hear a series of long single beeps indicating memory problems. Silence here indicates, in probable order, a bad PSU, motherboard, or CPU - or a bad installation where something is shorting and shutting down the PSU.
To eliminate the possibility of a bad installation where something is shorting and shutting down the PSU, you will need to pull the motherboard out of the case and reassemble the components on an insulated surface. This is called "breadboarding" - from the 1920's home-brew radio days. I always breadboard a new or recycled build. It lets me test components before I go through the trouble of installing them in a case.
If you get the long beeps, add a stick of RAM. Boot. The beep pattern should change to one long and two or three short beeps. Silence indicates that the RAM is shorting out the PSU (very rare). Long single beeps indicates that the BIOS does not recognize the presence of the RAM.
If you get the one long and two or three short beeps, test the rest of the RAM. If good, install the video card and any needed power cables and plug in the monitor. If the video card is good, the system should successfully POST (one short beep, usually) and you will see the boot screen and messages.
Note - an inadequate PSU will cause a failure here or any step later.
Note - you do not need drives or a keyboard to successfully POST (generally a single short beep).
If you successfully POST, start plugging in the rest of the components, one at a time."
If you suspect the PSU is causing your problems, below are some suggestions by jsc for troubleshooting the PSU. Proceed with caution. I will not be held responsible if you get shocked or fry components.
"The best way to check the PSU is to swap it with a known good PSU of similar capacity. Brand new, out of the box, untested does not count as a known good PSU. PSU's, like all components, can be DOA.
Next best thing is to get (or borrow) a digital multimeter and check the PSU.
Yellow wires should be 12 volts. Red wires: +5 volts, orange wires: +3.3 volts, blue wire : -12 volts, violet wire: 5 volts always on. Tolerances are +/- 5% except for the -12 volts which is +/- 10%.
The gray wire is really important. It should go from 0 to +5 volts when you turn the PSU on with the case switch. CPU needs this signal to boot.
You can turn on the PSU by completely disconnecting the PSU and using a paperclip or jumper wire to short the green wire to one of the neighboring black wires.
View: http://www.youtube.com/watch?v=5FWXgQSokF4&feature=youtube_gdata
This checks the PSU under no load conditions, so it is not completely reliable. But if it can not pass this, it is dead. Then repeat the checks with the PSU plugged into the computer to put a load on the PSU. You can carefully probe the pins from the back of the main power connector."
r/pchelp • u/Obessedwithshit • 12h ago
I'm thinking it's either ram or the gpu
r/pchelp • u/kreel_xeon • 35m ago
I got back from a week away and I turned pc on and loaded into a game noticed it was laggy so I checked device manager and realised it had a yellow warning mark. I have been trying to fix it since Thursday I have reseated GPU used other GPU slot I have no corruption in bios or safe mode. I have reset pc to factory and installed a fresh install of window made sure all drivers are up to date and used a ddu. I don't know what to do know any help is greatly appreciated.
r/pchelp • u/Next_Meat_6326 • 1h ago
So i have a problem with my cooler Deepcool AG400 2 Plus. Last time i notice before i change my mobo theres a little bit sag on my cooler and think it cause my old mobo cant support well the cooler.
Now i already change to new motherboard then i still notice the same sag. I already tried to tighten the screw in every part even on mobo and the cooler bracket but no one fix it from sag.
So its mean the cooler itself got bend or something factory thing ? I already follow every instructions from deepcool youtube channel with specific type too.
r/pchelp • u/BlueTarget_pg • 5h ago
So I recently cleaned out my PC with can air, and now my graphic card is making this weird noise after I cleaned it
r/pchelp • u/Upstairs_Stomach_823 • 2h ago
When I start my pc I get this idk what’s that.
It only pops up when I start valorant
Hi,
Im trying to turn on memory integrity for val (lol) but no matter what I do it won’t turn on. I am able to switch it on but once I reset it says it runs into an error and resets ):
It’s a fresh factory reseted pc, I have no idea what to do…
r/pchelp • u/Realistic-Machine212 • 53m ago
Im nearing the end of my university education and im going back home, sadly that requires a flight and I want to bring my PC back with me. I know I will take my GPU, CPU, RAM and storage while selling or giving away my case, PSU and monitors. But, I was wondering if it would make sense to keep my CPU, RAM and storage hooked up to the mother board and have all of that in a single box instead of packaging everything separately to save space or would the risk of damage be too high? I still have all of the original boxes and packaging material for each component.
I had a 3060 ti fe 8gb vram and it was perfect but I wanted to see if I upgraded my gpu if I could get even better 1% lows higher frame rate better pacing n just better input / latency overall bc i played on my homies setup who has a 5070 and even tho he had a worse cpu and worse WiFi his pc just felt super low input delay so long story short I got a 4070 ti and it has 12gb vram but when I even go into creative now on my same old settings its not even constant 277-280 it drops even to like 50-100 when I jump out battle bus and on my 3060ti fe it would hold 277 in bus and pregame lobby jumping out the bus it might drop to like 180 or 160 for a split second but that would js be the 1% lows the active frames would still show a smooth 277 and even mid fights it wouldn’t even move that much depending how far into the game or what’s going on the lowest the frames would go is low 200s now my shi goes to 100s mid fights depending what area of map or what’s going on in game and I even tried reinstalling drivers doing everything with ddu and nothing worked so I factory reset my whole pc and then re installed everything and it’s still just no consistent frames just trash 1% lows the game feels great and better than before and smooth when the frames aren’t dropping or moving but when it fluctuates a lot it makes that lil bit of difference that I don’t want bc I wanna try to play comp on pc
r/pchelp • u/Apprehensive-Yak6638 • 1h ago
Hi, my Samsung 980 PRO 1TB NVMe is acting really weird and I'm not sure if it's dead or fixable. Any help is appreciated.
**Setup:** Windows 11, ASUS TUF Gaming X670E-Plus WiFi, [CPU], 32GB RAM. I also have 2x WD SN570 500GB NVMe, a Toshiba HDD and a Samsung T7, and all of those work fine. Bought the 980 PRO on Amazon in July 2023, so it's about 3.5 years old. It sits under the motherboard's M.2 heatsink and still gets very hot.
**What's happening:**
- The drive gets SUPER HOT to the touch even with the heatsink. I don't know the exact temperature because Magician and CrystalDiskInfo can't read it when it's misbehaving.
- Windows used to be installed on it. It crashed constantly and then wouldn't boot.
- Steam shows "Disk Write Error" on every game I try to download to it.
- The drive keeps dropping out. File Explorer shows E: as NTFS, then a few minutes later chkdsk says the drive is RAW.
- When it drops out, Task Manager shows the type as "Unknown" instead of "SSD (NVMe)".
- When it's bad, it's missing from `Get-Disk`, CrystalDiskInfo and Samsung Magician, but `Get-PhysicalDisk` still lists it.
**What I've tried:**
- Moved it to a different M.2 slot [which slots]. Same problem.
- Full shutdown (not restart) and a cooldown. It comes back for a few minutes, then drops out again.
- BIOS: the drive shows up correctly (Samsung SSD 980 PRO 1TB, 1000.2 GB).
- BIOS NVMe self-test: Short = Pass. Extended with Controller and Namespace = Pass.
- Windows power settings: PCIe Link State Power Management off, hard disk sleep set to never, Fast Startup off.
- Bitdefender is installed, which I know can cause Steam write errors, but this looks like more than that.
**What I haven't done yet:** a firmware update (Magician only sees the drive for a short time), or testing it in another PC.
Thanks!
r/pchelp • u/Dry-Philosopher8748 • 1h ago
Hallo,
My Pc shows the cpu-led for a cpu failure on the mainboard but the pc is running normal. It only takes really long to boot. Especially after you unplug everything and reset the cmos
RYZEN 7600x
Gigabyte Arous Elite Ax rev. 1.0
64gb g.skill tridenz
No XMP activ, no overclocking
I tested all the usual things I could think of:
reset bios
reset cmos
update drivers
bios flash
RAM diagnostic
boot with a single RAM stick in different slots
doublecheck for loose cables
temperatures are normal
EDIT: I had a blue screen yesterday, but after restart it was all back to normal. No other symptoms.
You you have any further ideas?
Thank you!
r/pchelp • u/Small-Guarantee-870 • 4h ago
Hi everyone,
I’m having a frustrating issue with my PC after upgrading my CPU from a Ryzen 5 7600X to a Ryzen 7 9850X3D.
My PC was working normally before the CPU upgrade. However, ever since installing the new processor, I haven’t been able to get any display output or enter the BIOS.
The PC powers on, all the fans spin, the RGB lighting works, and the AIO pump appears to be running. However, the red DRAM debug LED stays illuminated on the motherboard.
Sometimes, the entire PC shuts down and automatically powers back on. This includes all the fans and RGB lighting turning off before starting again. It seems to be stuck in a boot loop.
I’ve spent quite a while troubleshooting this and have tried almost everything I can think of.
My PC specifications
* CPU: AMD Ryzen 7 9850X3D (new)
* Previous CPU: AMD Ryzen 5 7600X
* Motherboard: Gigabyte B650 AORUS ELITE AX V2
* RAM: 32GB DDR5-6000 (2 sticks)
* GPU: AMD Radeon RX 6950 XT (XFX)
* CPU cooler: ARCTIC Liquid Freezer III 360 AIO
* PSU: 1000W
* Storage: 1TB NVMe SSD
* BIOS: Attempted update to F41 using Q-Flash Plus
* Monitors: Two monitors, both normally connected via DisplayPort
Everything I’ve tried so far
Testing the RAM sticks individually
I removed both RAM sticks and tried booting with only one installed in slot A2.
When that didn’t work, I swapped it for the other RAM stick and tested again.
Neither stick worked individually, and the red DRAM LED remained on.
2. Trying different RAM slots
I also tried booting with a single RAM stick in slot B2 instead of A2.
Unfortunately, this didn’t make any difference.
3. Clearing CMOS multiple times
I completely shut down the PC, switched off the PSU, disconnected the power cable, and held the power button to discharge any remaining power.
I then shorted the two CLR_CMOS pins on the motherboard using a metal screwdriver for approximately 5–10 seconds.
I did this before and after attempting the BIOS update.
The issue remained unchanged.
4. Updating the BIOS using Q-Flash Plus
Since I suspected that the motherboard might need a BIOS update to support the new processor, I attempted to update it to BIOS version F41.
Here’s exactly what I did:
* Downloaded the F41 BIOS for the Gigabyte B650 AORUS ELITE AX V2.
* Extracted the downloaded ZIP file.
* Used a 32GB USB drive formatted as FAT32.
* Renamed the BIOS file from B650AELITEAXV2.F41 to GIGABYTE.bin.
* Placed the file in the root directory of the USB drive.
* Connected the USB drive to the dedicated BIOS USB port on the rear motherboard I/O.
* Left the PC powered off with the PSU switched on.
* Pressed the Q-Flash Plus button.
The Q-Flash Plus indicator and the USB drive both started blinking.
After a few minutes, the PC powered off and the flashing stopped, which seemed to indicate that the process had finished.
However, I still have no display, so I haven’t been able to enter the BIOS and verify whether F41 was successfully installed.
5. Waiting for DDR5 memory training
After clearing CMOS and attempting the BIOS update, I left the computer running for approximately 10–15 minutes to allow DDR5 memory training to finish.
Unfortunately, there was still no display.
During some attempts, the PC repeatedly powered itself off and back on.
6. Completely removing the dedicated GPU
I suspected that my RX 6950 XT might be causing the problem.
I completely removed the graphics card from the motherboard and disconnected its power cables.
The problem continued even without the dedicated GPU installed.
7. Testing the integrated GPU
The Ryzen 7 9850X3D has integrated Radeon Graphics, so I tried using the motherboard’s display outputs.
I connected a monitor directly to the motherboard instead of the RX 6950 XT, including testing the DisplayPort connection.
I also tried alternative display connections, including HDMI.
Unfortunately, I still couldn’t get an image, and the red DRAM LED remained illuminated.
8. Checking the CPU cooler
My ARCTIC Liquid Freezer III 360 appears to be operating.
The fans spin, the pump makes its normal operating sound, and the cooling system appears to be running.
I haven’t found any obvious signs of a cooling failure, although I understand that this doesn’t completely rule out a mounting or contact problem.
9. Checking the thermal paste
I used EarKings EK-1 thermal paste when installing the new processor.
I initially wondered whether I had applied slightly too much and whether some might have spread around the CPU.
However, the amount outside the CPU appears minimal, and the paste is non-electrically conductive.
I don’t believe this is the cause, although I haven’t completely ruled out a CPU socket contact issue.
10. Checking the motherboard debug LEDs
I inspected the debug LEDs on my Gigabyte motherboard multiple times.
The LED that consistently remains illuminated is DRAM, rather than VGA or BOOT.
The system never reaches a point where I can access the BIOS or see a motherboard splash screen.
Current situation
At this point:
* Both RAM sticks have been tested individually.
* Multiple RAM slots have been tested.
* CMOS has been cleared.
* BIOS F41 has been flashed using Q-Flash Plus, although successful installation has not been verified.
* I’ve waited 10–15 minutes for DDR5 memory training.
* The dedicated RX 6950 XT has been completely removed.
* The motherboard’s integrated graphics outputs have been tested.
* The PC still produces no display output.
* The DRAM debug LED remains red.
* The computer sometimes enters a complete power-off/power-on loop.
Everything was working normally with my Ryzen 5 7600X before this CPU upgrade.
What I need help with
Does anyone have experience with a similar issue involving Ryzen 9000 X3D processors, Gigabyte B650 motherboards, or a persistent DRAM debug LED after a CPU upgrade?
Is there anything else I can try that I haven’t already tested?
I’m especially interested in ways to diagnose whether this is a CPU, motherboard, BIOS, or memory controller problem.
I’d prefer not to reinstall my old Ryzen 5 7600X unless absolutely necessary. Ideally, I’d like to resolve this with the new processor still installed.
I’m also wondering whether the repeated full power-off/power-on cycles indicate something more specific than a typical DDR5 memory training issue.
Any suggestions, troubleshooting methods, or experiences with similar problems would be greatly appreciated.
Thanks in advance for your help!
r/pchelp • u/kespy6475 • 1h ago
Hello
I picked up a 2nd hand xfx 7900 gre and 1 fan doesn’t spin, I’m assuming it is dead, I have tried uninstalling all drivers and installing rolled back ones, forcing fans on with adrenaline fan control.
I haven’t gotten it to high temps yet, 55 degrees Celsius max and hotspot to 62 and not sure if the third fan has a certain threshold before starting? And whether it’s safe to run 2 fans with low temps?
Any ideas before I replace the fan with a new one would be much appreciated
Thanks
r/pchelp • u/Available-Jicama-844 • 7h ago
i got hacked and idk where the exe file is
r/pchelp • u/Screeinaotr • 2h ago
so my pc sometimes had this issue where it would turn on but the monitor wouldnt display anything, and usually I just turned it off and back on and it would be fine, or id just wait. But this time, I turned the pc off and it just wont turn on anymore, there's absolutely zero sign of any sort of power when I press the power button, even afyer power cycling. Just wondering if my pc is bricked for good or if there's something I can do about this. This pc is kinda all I had.
r/pchelp • u/Ok_Disaster_8870 • 2h ago
need help my old psu died so i bought a new one my gpu worked fine with my old psu until i got the new psu which says should be 50 series compatible it doesn't display on my monitor only through my mother board and it has this red light which i dont know what that means and on task manger it only shows my integrated graphics not my dedicated gpu (i have a rtx 5070)
r/pchelp • u/Booker-bookie • 13h ago
I’ve got a PC for a couple years now and just took it apart for the first time and I don’t know if it’s normal or not but I realized my RTX fan wasn’t running. Should I be worried about it?
r/pchelp • u/athos_T-31 • 4h ago
As the title says, I just started the process of formatting my PC and the monitor is stuck in "No signal detected" so I would like to know if I can recover the video somehow. I previously had a DP-HDMI cable cuz my motherboard uses DP exclusively, while my monitor uses HDMI but right now I just have HDMI
r/pchelp • u/warbloggled • 8h ago
It won’t budge, wiggle, come out straight to the left. At the other end it goes straight to inside the centerpiece of a fan.
ibuypower pre-built
Thank you
EDIT:SOLVED
… had to wiggle and pull WAY HARDER!!!
r/pchelp • u/Dry-Educator-9471 • 3h ago
Hey everyone,
I've been experiencing a strange boot issue with my PC for the past two days, and I'm trying to figure out what's causing it.
Whenever I turn on my PC, it goes straight into BIOS instead of booting into Windows.
Here's what's happening:
Yesterday, I encountered this issue for the first time. Every time I selected Save & Exit in BIOS, the PC would restart and take me straight back into BIOS.
After trying Save & Exit multiple times, it eventually managed to boot into Windows once.
Today, when I turned on my PC again, it went straight into BIOS and I'm unable to get it to boot into Windows.
BIOS displays "No Bootable Device Found."
I checked the NVMe Configuration section in my Gigabyte AORUS BIOS and noticed something concerning: I have two NVMe SSDs installed, but BIOS is detecting only one of them.
I'm not sure whether the missing NVMe SSD is causing the boot issue, whether my Windows bootloader has become corrupted, or whether there's a potential SSD or motherboard issue.
Update- Again after multiple save and exit in bios i am able to boot up pc to windows properly but i doubt if i shutdown again and restart it will go back to bios again
r/pchelp • u/Spiritual-Formal2061 • 10m ago
sup i came ere today to get some help for a new monitor basically ive been looking around for a moniter since i have a shitty gaming laptop but thats not the point so i wanna upgrade my setup with a new mointer what im looking for is one that is good for sim racing since im getting one for Christmas and one for gta 6 for when it comes out on pc my gaming laptop specs are
Gigabyte G6 KF (2024) – Iron Grey: Intel Core i7-13620H processor, NVIDIA GeForce RTX 4060 8GB graphics card, 16GB DDR5 RAM (2×8GB), 1TB M.2 NVMe PCIe 4.0 SSD, 16-inch WUXGA (1920×1200) 165Hz display, Wi-Fi 6E, Bluetooth 5.2, 54Wh battery, Windows 11 Home.
so im looking for a screen that is below 600 AUD and online or in store in australia
perferablly curved i dont mind if its oled or not good refresh rate for gaming and its mainly for gaming 2k-4k would be nice anyways thank you if u need anymore info lemme know