I have cleaned the mighty cooling unit by laying it inside a pot with 0,4L milk standing on the heating plate with very lowest heating level (1/9) and with some forks on the ground that the cooling unit does not get too hot. After 30mins I drunk just half the milk.

After fucking 2,5 hours I was hitted so bad by the trip. My complete body was shaking so crazy for 1-2 hours. I knew it would end but it was a very scary experience 😬😁. The shaking was not through psych. reasons it felt very physical. After 2 more hours I was so high as I knew it from vaping a lot. Then I fall asleep.

Did you guys also had such a strange experience with this strong body shaking?

I just lost the filling aid for my Mighty and want to get a replacement. It's only $6 thru S&B but they charge like $12 shipping.

Any other good sources for Mighty accessories? Ebay hasn't turned up much.

Has anyone done it yet.Where did you get your batteries?

I'm so confused.. when you put it on the pad, it basically liquifies it.. how does none of it get into the actual machine?? I'm gonna be honest, this has been blowing my mind all day... first time with wax and I just don't get it!

Hi all -

I have been loving my Crafty for the past few months, but on Wednesday during a session it turned off (battery was halfway depleted) and will only flash blue light without turning on. The app recognizes the device and states it's low battery, but does not seem to register the device has been charged overnight.

Troubleshooting forums suggest to hold the power button down for 10 seconds, but that is of no use as it can only be done when the Crafty is turned on :(

Any tips or suggestions would be great appreciated! Thanks so much!

Hey what's up guys? I been hooked on the Mighty for about a year and a half now, and it's great but I've gone through like 6-7 AC adapters so far and I don't see this getting better unless I find a more beefy option. All of them develop the same short out near the elbow connector with a few months of use. I've been seeking alternatives on Amazon but I'm unfamiliar with the connector sizes, so I could use some help.

Has anyone found a forever power supply for their mighty yet? I'd love a link to where I can share in your joy. :)

Thanks!

I’ve been using the mighty for about 6 months now and it’s great, but it takes me so long to finish a bowl. It can take like 40 minutes because I start at 356 Fahrenheit and once it starts vibrating to turn off on its own, I flip it up 3 degrees each time until it gets to 395. This seems to make the avb browned enough that I think the bud is done, but it takes so long. If I go for shorter sessions and just up the temp sooner or start at a higher temp, the avb is lighter and the high isn’t as potent it seems. Any way to keep the high without the long sessions?

I would assume it would be stainless steel but I can't find out for sure.

I’ve had my mighty vape for a few years now idk if this is common but when I clean my mighty vape and take out the screen from the bowl and clean it with iso propylene it cleans the bottom of the bowl just fine how ever when I turn it on and heat it up with out a screen in it it still burns a lot vapor off the bowl even though it have nothing in the bowl and the bowl is spot less Idk if this is something I should be worried about I obviously don’t want to to be inhaling anything bad my theory is that plant particles got through the screen went into the the holes in the bottom of the bowl is that possible should I be concerned? If my theory is correct how do I clean out the how holes in the bottom of the vape?

My mighty bout in this year started doing buzzes wile charging do you know what should I do? I thought is the charger maybe.

Hey guys just thought I'd share another really easy method to get more from your avb. I used a very small amount of avb around five grams and isopropyl alcohol.

First freeze the ISO for around thirty minutes and decant you avb into a container with a lid.

Then once you have a very finely ground mix in the ISO just enough to cover it.

Shake vigorously for exactly thirty seconds and pour through a fine sieve into a Pyrex dish. You can if you like put an extra swish of ISO back into the bottle to get the last bits out.

Then press the soaked avb until dry and remove dish with solution for drying.

I'm using a fan currently an no heat at all for approximately 24 hours making sure to break it up pretty regularly to ensure sufficient surface area for ISO to evaporate

NOTE* i also use ISO to clean the cooling units and stem and see no reason as to why you can't take the ISO from a bath used for cleaning the pieces and add it to the solution you use for abv to make sure you have zero wastage!

The final product is a very fine earthy material . Obviously I'm not expecting wonders in terms of strength but I've recently quit tobacco so I hope it will give my blunts a nice kick. Thanks again guys.

What cases do you all use for your Mightys?

I'm a longtime Pax user, and I use my Pax3 pretty much daily. I usually only use the first two temps.

I smoke primary indica and love the body effects it gives me. Hate sativas as they give me anxiety, headband, tension headache and that pressure in your sinuses.

I got a Mighty last week and have been using it all week with dosing capsules and I hate the high.

No matter what of my go to strains I hit, I get the same feelings listed above. In my Pax, no issues and a straight body buzz with none of that head pressure.

Am I doing something wrong, or is The Mighty just in a different class.

Also find I prefer the nutty/toasty flavor the pax gives me. Is it closer to smoking maybe?

Just looking for some opinions ...

Hi guys,

I'm using the dosing capsules with the Mighty - they seem to be building up wax on top of the capsule lids and I've noticed that it carries on 'smoking' after I've used it. Am I inhaling toxic vapour? Or is this normal for the mighty?

I don't want to break this awesome bit of kit. Is it maybe time to clean the cooling unit?

Any help would be greatly appreciated!

I have been hearing talks that there might be a new mighty coming out but I can't really find any information about it anywhere. I was wondering if I should buy a mighty now or wait for the next version of it?

How do you guys do it? 3/16 food grade piping to rubber bung?

Does anyone know how to check the firmware on a Mighty, or how to determine what it is based on the serial number? There are some old posts about it here, but I can't find a specific reference.

Thanks for any thoughts.

I’ve tried pushing hard on it with an iso dipped q tip for like 3 minutes straight after a burn off and not much of anything came off. A lot more came off from the heating chambers screen just going back in after cleaning actually since it’s scraping the sides. I’d appreciate any help as it’s almost a whole layer of this dark brown residue on the sides of the heating chamber

Is there somewhere I can just order bulk of the fine screen that comes with the mighty? I don't use the coarse one, as I get scooby snacks when I do, but the fine screens are perfect.. all the packs I can fine are 4 coarse screens and 2 fine.