r/meshtastic • • 4h ago

Just received SenseCAP P1 Pro. Is it okay for me to deploy it stock (w/o additional waterproofing)?

Post image
30 Upvotes

Probably the worst time to deploy climate-wise (it’s almost winter here) and weather-wise (rain and snow soon), but what needs to be done must be done.

I heard the battery degradation issue via low temperature isn’t as bad as people make it out to be, hence I’m just worried about water seeping issues. Anything I can do to make it more water resistant (or waterproof)?


r/meshtastic • • 13h ago

Two mile range on WisMesh High Power Booster Starter Kit and 3dBi antenna inside suburban home

Thumbnail
gallery
99 Upvotes

Hey all - just wanted to share my results! Obviously, YMMV.

I recently picked up the WisMesh High Power Booster Starter Kit from rokland and hooked it up to an Alfa AOA-8696-3ACM antenna. It is about 16 feet above ground level. On the wisblock, I set boosted rx to true and 30dBm as the power.

Using a Heltec T114 with a Muzi works whip antenna, I was able to make a direct connection to it up to 2 miles away! This also meant that the signal was going through about 10 homes.


r/meshtastic • • 1h ago

Meshtastic for Long-Range, Grid-Down Communication — Can I Reach Family 25–100 Miles Away?

5 Upvotes

I'm really curious if this kind of question has been asked a million times before, and I'm sure it has.
My name is Kyle, and I've recently been putting together survival gear, bug-out bags for both my car and my wife's car, storing food, and generally preparing as best I can in case the power grid goes down or something along those lines.
I've spent the last couple of weeks researching and getting myself as prepared as possible. One of the last things I'm trying to figure out is communication.
If the grid were to go down and cell towers stopped working, I would have no way of communicating with family members who live miles away from me.
I've obviously done some research and came across these Meshtastic devices. From the little research I've done, it seems like these devices aren't capable of communicating over very long distances.
I have family members who live 25–30 miles away, and from what I've read, it doesn't seem like these devices are capable of reaching anywhere near that far. Am I wrong? Are these devices capable of communicating over distances of 25–30 miles, or even 100 miles?
Are there any devices or communication systems that would allow you to communicate with family members over long distances during a grid-down situation when cell towers are no longer working?
Or are Meshtastic devices primarily intended for short-range communication?
Help me out here, lol! And again, I apologize if this topic has already been asked a million times.


r/meshtastic • • 13h ago

Working on Cardkb support for InkHUD devices.

31 Upvotes

r/meshtastic • • 7h ago

New message indicator won’t clear

4 Upvotes

I’m using the iPhone app, and on one of my nodes, it shows an unread message, but when I check all my channels, there are none. Is there a way to clear this? I’ve looked everywhere and it’s driving me nuts.


r/meshtastic • • 10h ago

rpi vs heltec repeater

2 Upvotes

Hey all, looking to set up a meshtastic node in my city. I have my own heltec V3, but since I live on a hill I was thinking of setting up a fixed node/repeater at my flat. I have some raspberry pis lying around but I am wondering if using a rpi5 as a node may be overkill. I am not sure if the meshtastic firmware would allow me to use the pi for anything else, and I am also unsure whether more powerful hardware is better as a node. As of now I can't think of any reasons why, but would be great to get a more expert opinion. Also, if there are projects that can exploit the rpi hardware that would benefit the mesh in any way feel free to suggest! :)


r/meshtastic • • 16h ago

Help finding node locations

5 Upvotes

Does anyone have a successful pitch for local businesses or organizations to convince them to let you put a solar node on their roof? I don't mind asking people but I can't think of a pitch that doesn't seem like it will just confuse and weird out the person and get a no. There's got to be a way to make it sound cool or like good karma to let me put one up


r/meshtastic • • 15h ago

Wio Tracker L1 Pro receives fine but nobody hears my messages (south Minneapolis, MSP Mesh)

4 Upvotes

Hi all, new to Meshtastic and stuck. My node hears the mesh well, but I can't tell if anyone hears me.
Setup:
Wio Tracker L1 Pro, stock antenna, firmware 2.7.26
US region, MediumFast, slot 0 (matches MSP Mesh, 913.125 MHz)
Role Client, TX power 30 dBm, Transmit Enabled on, RX Boosted Gain on
South Minneapolis (around 60th & Portland), upper-floor window, antenna upright
What happens:
I receive lots of messages and see many nodes, including some 1 hop away
Every message I send shows "Failed to deliver to mesh" / "Not delivered" in the iOS app
No replies, and my node (SouthMSP1221, !b505835a) doesn't show on monitor.mspmesh.org
What I've tried:
Tested outdoors in an open park (Veterans Park, Richfield), antenna upright
Reseated the antenna
Sent from both the app and the device itself
Updated firmware, rechecked region and preset
Can anyone nearby check whether you see SouthMSP1221 (!b505835a)? Also curious if this sounds like a weak or bad antenna, a hardware fault, or something I'm missing. Any tips or a recommended 915 MHz RP-SMA antenna would be great.
Thanks!


r/meshtastic • • 17h ago

Meshtastic enclosure/3d designers and DIY's. I need your advices.

5 Upvotes

Hi everyone.

I'm planning to buy the Wio tracker L1 e-ink kit, and my idea is to design and print my own enclosure. I've seen a lot of good cases and designs but somehow none truly fullfill my "demands".

The "already made" design for this model I like most is the meshnology N37E.

The main purpose for the device will be backup communication if the shtf. It need to be portable, but should stay connected to a PC during the weekends. For that I'll create a Vesa mount/rack to put the meshtastic and a baofeng radio side by side.

The most important thing in the design I'm planning will be swappable batteries.

It would be perfect if you could swap a dry battery for a full charged one in a few secs. Probably I will use 18650, AA or AAA for the convenience. I know there's better battery options on the market, but I wanna make a post apocalyptic proof device. Those batteries will still be easy to find if the internet and the online ordering goes away.

The design must protect the antenna connector.

it should have a lanyard fixing point, and a molle clip for back packs.

Now my doubts are:

Can I use an antena extension? For example to have the device inside the backpack, and the antenna out.

If I connect the device by USB cable to a smartphone does the device work? I mean, the USB can power the board directly?

For those of you that build your devices from scratch, what do you consider to be the most important things in the enclosure design?

And where do you order your components like battery connectors etc...


r/meshtastic • • 21h ago

do not update the firmware of meshpocket up to 2.8

10 Upvotes

You can disable the MeshPocket's power management.

Even after rolling back the firmware, the MeshPocket was permanently dead after the second cycle.

Right after the FW update, the surface of the MeshPocket gets hot, like a battery-powered hand warmer.

Finally, I lost two MeshPockets due to firmware issues.

Would you like to suggest any other products with a longer battery life, or is DIY the best option for me?


r/meshtastic • • 20h ago

Magnetic base car roof antenna

8 Upvotes

Has anyone ever tried fitting an antenna like that on the roof of their car, or does the cable completely ruin the reception? I’m aware that signal loss is relatively high with a cable like that.

https://amzn.eu/d/02xj5qQF


r/meshtastic • • 17h ago

Meshtastic node to monitor 12v

3 Upvotes

I'm looking for a method to monitor a 12v source voltage over meshtastic.

Application is to have a always on node in my car powered by the 12v.

But, have the ability to see the 12v voltage so i can remote start car if needed to top off car battery.

I understand i can run any node via 5v and step down the car 12v to 5v to power the node.

I guess my question is a streamlined method to monitor a 12v source voltage powering the node with either 12v or 5v.

Thanks in advance!


r/meshtastic • • 1d ago

self-promotion SNAP v1.2, 4×60mA variant: a solar node enclosure you don’t have to aim. Feedback welcome

Thumbnail
gallery
69 Upvotes

Last month I shared the dual 200mA version of SNAP. Thanks for the comments and suggestions. This is its sibling, with four 60mA panels, one on each side.

This variant is fully symmetrical, so you don’t have to aim it. At least one panel faces the sun for most of the day, which suits RVs, vehicle roofs and spots where you can’t pick the direction. The tradeoff is less peak input than the dual 200mA version, because only one or two panels get direct sun at a time.

One of these builds has been deployed on a hill for the past 2 months. It stays above 80–90% charge, even on cloudy and rainy days.

Differences from the dual-panel version:

  • Panels: four 60mA panels, each held in a slide-in lip.

  • Ports: two accessory ports, top and bottom. With panels on all four sides, there’s no room for side ports.

  • Accessories: the same plugs work on both. The antenna mounts, hook, painter’s pole thread, magnet cap and power switch fit every SNAP variant.

Weatherproofing: I print it in PETG or ASA, with TPU filament as the base gasket, conformal coating on the solder joints, and spar urethane over the panels. Lately I’ve also been spraying rubberized sealant inside. That may be overkill, since it was dry every time I checked after rain.

Feedback is always welcome!

Files, parts list and print profiles: https://makerworld.com/en/models/3321870-mesh-lora-solar-node-enclosure-4x60ma-panels


r/meshtastic • • 1d ago

Where to start?

12 Upvotes

Tl;dr; Any recommendations where to start? I like to tinker.

-

I was researching Black Friday deals to expand my gmrs setup then came across Meshtastic and I’m fascinated!!! I live in a condo bldg in a big city so unsure about the local network but I’m curious to test if I can keep my initial investment under 50$

I plan to buy one small device to test it out and if it works and I see value (nearby nodes) I’ll purchase a solar powered device and attach it to my balcony with another for the car. And smaller ones for backpacks.

Any recommendations?


r/meshtastic • • 2d ago

I turned a dead 2007 AT&T 8525 into an off-grid Meshtastic messenger

Thumbnail
gallery
465 Upvotes

My old AT&T 8525 (HTC Hermes, Windows Mobile 6) had been sitting in a drawer for years with no service. Now it's a dedicated Meshtastic texter with a real slide-out keyboard.

How it works: the phone has no BLE, so it can't pair with a node the normal way. Instead, a cheap ESP8266 (D1 Mini) makes a little Wi-Fi hotspot, and the phone and my Heltec V3 both join it. MeshChatCE, a native Windows Mobile app I wrote, talks to the node over the Meshtastic TCP API. No cell service or internet anywhere.

What it does:

- Channels and DMs, with delivery status

- Texting-style chat bubbles; light, dark and red night themes

- Nodes list with SNR, hops, battery and distance; traceroute; favorites

- Bluetooth GPS position sharing and a radar-style offline map

- Range log to CSV, mesh stats, quick replies

- Rename your node and swap keys from the phone

- Pop-ups, vibration and notification light

The Heltec, the ESP8266 and a LiPo all fit in a small box on one battery and one switch, so the whole kit is pocketable.

It's free and open source, with a setup guide and the hotspot sketch: https://github.com/AughtCool/MeshChatCE

Built with a lot of help from Claude (AI). I did the hardware, testing and debugging on the real phone.

If anyone has another Windows Mobile 5/6 device (iPAQ, HTC Touch, etc.) and wants to try it, I'd love to hear whether it works!


r/meshtastic • • 17h ago

Beware the Mesh Tick

Post image
0 Upvotes

Have you been bitten by the mesh tick?!

Symptoms include:

-Extreme desire to connect

-LoRaVision(always looking for a good node location)

-Constantly texting "did anyone receive this?"

Anyone know of others symptoms?


r/meshtastic • • 1d ago

Recent Meshtastic experience

29 Upvotes

Good morning, guys. So, I recently bought a pair of Meshtastic units. Assembling them, flashing them, and getting them online was a breeze. Installed the software - I connect my phone to one of them and my notebook to the other.

I've detected hundreds of other nodes, and LongFast shows a reasonable amount of traffic each day. But, I have never had a reply to a message, nor have I ever seen a real "back and forth" conversation. There are people there, but as a community it's "dead."

This is a real shame - my main interest in the technology was that it offered a possible communication method that could serve even when all the centralized comm options are offline (say, in a major storm or something like that). But - if no one ever replies, it doesn't do a lot of good.

I'm wondering this morning if anyone has experiencing organizing a formal community network, where volunteers take standard time slots during which they'll be watching and prepared to try to arrange assistance for anyone with an urgent need?

It feels like we're letting a really valuable opportunity just "lie fallow" here.


r/meshtastic • • 1d ago

Faktec red led won't light up, but charging. what does that mean?

1 Upvotes

r/meshtastic • • 1d ago

SenseCAP MeshTracker X1 – Unable to Send Messages. Has Anyone Experienced This?

2 Upvotes

Hi everyone,

I recently purchased a SenseCAP MeshTracker X1, and I’m having an issue with sending messages.

The device connects successfully to my iPhone via Bluetooth, detects over 40 nearby Meshtastic nodes, and receives data without any problems. However, every time I try to send a message, it stays on “Sending” for a while and eventually fails with an error.

I’ve already tried multiple troubleshooting steps, including:

● Testing the device in different locations, both indoors and outdoors.
● Checking and adjusting the device and app settings.
● Restarting the device and reconnecting Bluetooth.
● Updating the firmware.
● Checking the channel and LoRa configurations.

Unfortunately, nothing has resolved the issue. The device can detect nearby nodes but simply cannot transmit messages successfully.

Has anyone experienced this exact problem with the MeshTracker X1? If so, what was the solution?

I’m trying to determine whether this is a firmware issue, an incorrect configuration, an iOS compatibility problem, or potentially defective hardware.

Any specific troubleshooting steps or confirmed fixes would be greatly appreciated. Thanks!


r/meshtastic • • 2d ago

should i start meshtastic

13 Upvotes

okay, so this meshtastic thing seems really cool but i dont want to spend all the money to get into it and then not really like it and have it sit on a shelf forever. like i got a ham radio like a year ago and its mainly been sitting on a shelf (but i will say that is probably because its not that fun without a license and then i dont want to put in the effort to get the license. y'know catch 22) i do think this would be cool but i dont know what i would do with it really like is there much use if i dont like buy 2 of them to give one to a friend or something. like this really sounds cool i guess i just need that push to get me to take the leap. also what would be a good node setup for pretty cheap i would like to know (i have like $50 but i wouldnt want to spend all of that) so any help would be appreciated, thanks!


r/meshtastic • • 2d ago

⏰ Reminder: we're live tomorrow!

Post image
42 Upvotes

Join us for a walkthrough of what's new in Meshtastic 2.8.

🕗 Sat, Nov 14 · 6 AM PT / 8 AM CT / 9 AM ET / 14:00 UTC / 15:00 CET

Live on YouTube, Facebook, Instagram and X


r/meshtastic • • 3d ago

vendor The MeshTracker X1 is in stock now, did you receive yours?

Post image
63 Upvotes

r/meshtastic • • 2d ago

Apple Mac G4 style E-Ink node

Thumbnail
gallery
6 Upvotes

My handmade node with 4.2" E-Ink display, MakerDiary Connect Kit nRF54L15, BME280 and Core1121-HF 22dbm transceiver.

I found the model for the stand on makerworld, but I had to design the enclosure for the electronics myself. There was a lot of hassle with the firmware, because the nRF54 is a fairly new chip with unofficial support