r/livesound • • 5h ago

Gear New project: Virtual Allen & Heath SQ+ running its own firmware (same approach as my virtual WING)

20 Upvotes

If you've seen my virtual WING updates (latest: Update #4), this is the same idea on a different console: a software Allen & Heath SQ that runs the console's own firmware instead of a re-creation. I started it this weekend, and it already boots to its home screen and works with touch in a browser.

Quick recap of the idea
The SQ update file (SQ-6, V2.0.3 r7040). It's a standard Xilinx boot image with the main app, a USB app and the FPGA image inside. The main chip is a Xilinx Zynq (two ARM cores plus FPGA logic), so I emulate that chip and let the real firmware run on it. Nothing in the firmware is patched.

What works

  • It boots like the real thing: SQ+ splash with the progress dots, then the home screen with the "Update your mixer" pop-up.

  • Touch works, through the console's own touch driver. Clicking in the browser goes through an emulated touch controller, and the firmware reads it the way it does on the desk. Tap "Ok" and the pop-up closes. Tap "Brightness" and it opens the Surface Pref page.

  • The screen runs in a web page, like the WING one, with the console's text output underneath.

  • Some code carried over from the WING emulator since both consoles use the same type of ARM processor. Most of the rest is new, because the Zynq's peripherals are different.

What's still limited

  • No audio yet. The mix engine and FX run in FPGA logic (the FX on two separate chips). From what I've seen in the firmware, those parts are program-driven, so emulating them looks possible, but it's a big job.

  • No faders or surface, and no FX engine. The firmware notices the fader board is missing and carries on.

  • It's slow: about 1/80 of real time, so a tap takes a few seconds to show. With the WING I got the console side faster than real time, so I know where to start.

What's next

  • Network support, with the goal of getting SQ-MixPad to connect to the virtual console.

  • Speed. Most of the time goes to the firmware checking a timer over and over, and each check is slow in the emulator.


r/livesound • • 6h ago

Question Recording our show tonight, need advice on where to put audience mics

2 Upvotes

My band is getting a multi tracked recording of our show tonight, gonna want to release it as a live album sometime in the future so we're setting up audience mics. Not a huge venue, its a restaurant with a bit of a dance floor, not a huge stage either. I have two Rode M5s that I use for concert taping and its what I got so its what we're gonna have to use. Was wondering if it would be preferable to have the mics on the stage pointed at the audience, or in the audience pointed at the stage? Should they be spaced far apart or would my stereo mount work? I've recorded shows from the audience for the sake of capturing the show, not sure if that would be a similar way to go about recording this


r/livesound • • 6h ago

Question Angry soundguy, why are you the angry soundguy?

93 Upvotes

Over the last 10 years or so ive done maybe a thousand or so shows and I still haven't turned into the jaded angry soundguy, I still remember how shitty it felt as a musician to come to a new place and just feel unwelcome and its still brewing in the back of my head that i dont want to do that to people.

So if you are the angry soundguy, how come?

Reference and also a fantastic video.

https://www.youtube.com/watch?v=LdCLRIA7Ah8


r/livesound • • 9h ago

Question RCF KX 32-A - what's the RMS on this box?

2 Upvotes

Hey there. RCF recently seem to have stopped publishing the RMS value of some of their active speakers and instead are just posting the peak output.

For example, the KX 32-A, which is a replacement for the old TT 22-A, is rated on the RCF website with a 3200w peak.

But I'm not really interested in peak ratings. If I want to play music then the peak value is useless to me - if I play something continuously at the speaker's peak, then it will probably catch fire after a few minutes.

I've noticed the peak rating only listed before with some of the NX and ART range speakers, but now it's in their KX range too, which is meant to be their premium range.

So if the KX 32-A has a peak rating of 3200w, then going on previous ratings, the RMS would be 1600w - but that seems very high compared to similar products. And would be a massive increase on the previous 1100w RMS rating of the TT 22-A.

Any thoughts? Thanks.


r/livesound • • 12h ago

Question Waves LV1 Classic tip: Disable the default Shortcut 1 & 2 buttons before a volunteer accidentally fires a scene mid-service

23 Upvotes

What are you guys remapping Shortcut 1 & 2 to on your rigs?

Quick 40-second walkthrough for anyone running or transitioning to a Waves eMotion LV1 Classic—especially if you have volunteer operators.

Out of the box, the two physical Shortcuts (1 & 2) buttons right next to the pages on the fader bank are mapped to Next Scene / Previous Scene. One accidental bump during a live service and your whole mix recalls the wrong scene.

Quick fix (takes 10 seconds):

  1. Go to Setup → Inventory

  2. Under Controls, click the gear icon on LV1 Control (Fader Bank)

  3. Find Shortcuts (1 ★ and 2 ★) at the bottom right

  4. Change both from Scenes to None (or remap them to something safe like a tap tempo, mute group, or layout view)

This is one of the first things I lock down whenever I build a showfile.

What are you guys remapping Shortcut 1 & 2 to on your rigs?


r/livesound • • 18h ago

Question Guide to running monitors?

29 Upvotes

So, I ran a show's soundcheck as a monitor engineer and barely made it through- are there any good YouTube channels that break down the basics of being a monitor engineer? My gain structure was separate from FOH, but somehow it kept fucking me over when I was using sends on fader. It didn't help that I was unfamiliar with the DM7 console I was on, but I really want to take a look back to the basics and figure out what I was doing wrong so I can do the next monitor gig and not feel like an idiot the whole time.

Like, I couldn't even figure out how to set up my cue wedge, cuz I've never needed one at FOH. I wanna learn stuff like that.


r/livesound • • 1d ago

Question DM7 Call Light With Stream Deck

21 Upvotes

Does anyone have a solution to creating a call light for FOH to get on comms using the DM7 with Stream Deck? I've seen macros triggered on Digico to accomplish this, but the LED control for the DM7 is only controlable by User Defined Knobs and there is no action for that in Yamaha-RCP. I've experimented with flashing input channel color strips on and off, but it's not impactful enough to notice. Any ideas?


r/livesound • • 1d ago

Question Issues with routing audio through a laptop in a live set

9 Upvotes

For the past year or so, I've been working on this very experimental live set that involves me manipulating live vocal audio signals in various ways, to put it very basically.  There are elements of live looping, but it's more about applying the principals of turntablism to live sound or buffered sound from a live source.  I did initially try to achieve all this just with audio hardware, but it pretty quickly became apparent that I was going to have to route everything through a laptop to achieve my vision.

So here's my issue: ... Okay every time I start to explain the issue, the "post" button greys out and this warning message appears that isn't applicable to me. AI is so frustrating. I'm going to see if I can post the rest of my message in a reply...


r/livesound • • 2d ago

Question SM58...failure.

40 Upvotes

Hi everyone, so I had no idea this could happen, but I have just had an SM58 fail on me. No, it was not dented! It was actually less than a year old, it just dropped in the middle of a gig.

Afterwards I opened it up, and found that everything connection wise looked solid and nothing was crossed. I read about 18 ohms of resistance across pins 2 and 3.

I found a seven year old forum that has helped me do a bit of troubleshooting, but thats about all I could find since these things almost never fail. Before I conclude that it is the transformer, is there anything else that I should check?


r/livesound • • 2d ago

Gear Made some antenna and volume protectors for Shure PSM900 and PSM1000 beltpacks. What do you think?

Thumbnail
gallery
140 Upvotes

r/livesound • • 2d ago

Question Live mixing: Backing track advice

13 Upvotes

Hi.

Had a longer post but not sure of the character limit.

For small local venues. Trying not to overcomplicate and ruin an engineers day.

I am aiming to play guitar and vocals, accompanied by:

Drums (I have access to some unmixed live drums, but wondering if I should use a Drum VST for consistency of sound)

Bass

Guitar layers

Some additional synths, piano, strings, backing vocals

I was thinking that I could play the tracks live from a daw on a laptop, possibly with a small mixing desk to provide outputs for each group for the engineer to mix as they need.

Is this a good way to approach or is there a better way?

I suppose my main question would be, how much control of these elements would you want if you were mixing this?

Are there any absolute no's or things to avoid?

(Should it be all mono, is it better to have a pre-mixed sound or leave the compression and eq to the engineer etc)

Any tricks to convey that live energy when tracks are pre-recorded?

Anything I've overlooked?

Thank you


r/livesound • • 2d ago

Gear Soundcraft UI16 can't press record (not grayed out)

5 Upvotes

Plugged in 8gb FAT32 usb into REC port. Record and play button are not greyed out but I can't click any of them (nothing happens when I click). The sound output is working, just not the record function.


r/livesound • • 2d ago

Question Live drums mics and recording

5 Upvotes

My band is thinking about recording our live sets using our IEM mixer. For drums, we have just a single mic in the “wurst” position going to our ears. FOH puts all the mics (usually around 8 or so) on the drums that they need.

Since we want to record we are thinking about having FOH route there mics through our splitter. However, we only have 5 spare channels to dedicate to recording drums. Which 5 of the FOH mics should we route through our splitter to get the best live recording? Our drummer uses 2 rack toms btw. I was thinking kick, snare, floor tom, and 2 overheads. Thoughts?


r/livesound • • 3d ago

Question Getting over a “bad” show

48 Upvotes

Hey guys!
I’m fairly new to live sound, I started learning basics about sound/tech at the start of the year in class, then started doing liveshows a couple months back. I’ve got ~25 shows by now.

Today I had one, that during soundcheck I felt it was fine, then when the actual show started, there were some real annoying frequencies, but they were spread out enough that I couldn’t get them with the EQ, without cutting out things that we wanted in.

Artist was happy, crowd was overall happy enough, though a couple commented on the sound not being great, and honestly I agree with them. I’m not super down or anything, just a bit annoyed because I felt like I should’ve been able to “fix it.” And because we had a promoter in the crowd, who’s been at two shows I’ve mixed, and the other had a lot of tech-issues, so I’m just annoyed they’ve only seen the “bad” ones lol.

So my questions is: what’s your go to move, after a show you weren’t super satisfied with? Like how do you deal with the meh-feelings?


r/livesound • • 3d ago

Question Engine issues with the DiGiCo SD7

8 Upvotes

I am currently on an SD7 that uses Optocore for all it's connections. I am all of the sudden having issues with engine B. It inexplicably is causing popping and overload on local channels ONLY on the engine B side and is a major issue when mirroring engines. Channels on the SD rack over optocore or orange box don't pop until the console is mirrored. My short term solution is to not mirror but keep engine B updated by sending the session constantly.

The engines also no longer mirror on the first try, board claims the sessions are not the same but mirror on the second try anyway. I really thought this was a clocking issue but everything is correctly set to follow optocore.

I've tried everything but cannot seem to isolate this issue, leading me to believe its a PSU voltage issue on the DiGiCo. DiGiCo rep wasn't that helpful, blamed a dante card that we don't have and said voltages look fine, which is strangely true. Anybody have an advice? I am at my wits end.

If it's relevant this space never connected optocore to engine B, but apparently has never been an issue.


r/livesound • • 3d ago

Question How did we go from The Beatles playing their amps in the middle of Shea Stadium to Line Arrays flying from the rafters and Subs the size of a wardrobe closet?

165 Upvotes

Is there a video on YouTube that breaks down how we went from a PA that looked like an air raid siren in the 50s and 60s to where we are today? (And what was that excursion into the Wall of Sound with the Grateful Dead? Clearly that approach didn't stick.)

How can I, a lay person who occasionally gets to assist with load-in and load-out at large concert venues (theaters, arenas, stadiums) get a basic understanding of the progression of Live Sound Reinforcement? Basic being the key. Thanks! 🤘🏻


r/livesound • • 3d ago

Question Strange response in system tuning

Post image
12 Upvotes

I just recently tuned a theaters system for the first time. That being said I didn't go in blind, I've been researching how to properly do it for a least a year at this point, so I was confident but this was just the first opportunity that I've had to tune a system. The magnitude came into shape really quick and the space is sounding alright. Except there is a bit of phasing between the left and right main speaker, but I ran out of time to fix it then. That was Monday, but today I actually went and looked at the snapshots in the OSM and actually flipped to the phase graph and it looks strange. There are really strange jumps at like 350 and 16k. I know it's not normal but I don't completely understand what I'm looking at so I just want some help understand it.

I've attached the phase graph and the coherence. This is just on the left speaker, but the space is mirrored, so the other side of the room look similar. The blue line is before tuning and the teal is after I tuned. I didn't set any delays on my main speakers so that's why nothing has shifted too much.

One thing to keep in mind the venue is an old Vaudeville house that has been retrofitted with a Bose sound system. Not great but also not bad.


r/livesound • • 3d ago

Question Who's coming to NAMM in January!?

0 Upvotes

I will be there with BoxCast. Would love to connect with some of you guys!


r/livesound • • 3d ago

Question - ¿What Now? This is not months or weeks away. This is Now.

0 Upvotes

Muse have enlisted a robot roadie to work their sound desk! Here's a look at them diligently keeping Knights Of Cydonia sounding brilliant as ever... 🤖 standing next to a FOH console not doing anything.

https://www.instagram.com/reel/DfsjCe0N08d/


r/livesound • • 4d ago

Question Some thoughts on A&H Qu-3D

0 Upvotes

Hey everyone,

I am personally quite fond of A&H as a whole and am quite excited for the Qu-3D launch. But I do work at a Yamaha-first company. And I don't really see how it fills any gaps.

I mostly think of the Qu-3D as a QL1 in a DM-3 form factor. But there are some disadvantages that the QL1 doesn't have, mainly no secondary Dante.

Let's be upfront first: nobody actually likes the DM-3 but we own like five of them regardless, Why? Because it's a super small form factor for a little conference room on the side somewhere and with like 4-8 mic inputs and maybe a laptop.

The main advantage of the Qu-3(D) as compared to the DM-3 imo is the amount of processing and inputs, but it doesn't really have an edge over the QL1. When we get into the category of more inputs I would like to just have everything in Dante, so I don't have to patch 25 inputs from different devices all over the place to a single point. But Dante for us (almost) always means Primary and Secondary networks, so that one defective copper link can't take down your show.

(continued in comments)


r/livesound • • 4d ago

Gear Yamaha DZR missing from website?

10 Upvotes

I was checking their website to find the datasheets for the passive CXS subs when I noticed both those and the DZR speakers are completely gone with no replacement.

The other subs in the lineup are bandpass which are simply different and the DZR doesn't have an obvious replacement as the highest end option. There's also no announcements on new PA products or anything like that present.

What gives?


r/livesound • • 5d ago

Question What certifications are best for Live Sound?

23 Upvotes

Hey y'all! I'm an audio engineer looking for SOMETHING in my field of study and enjoyment lol. I know the job market in the US is not the best right now, but I have a Bachelor's in Music Performance and a certification in Audio Engineering I got last year. I record, mix, and master my own music as well. I've applied to several AV jobs and only gotten one interview which I didn't get hired for. Which certifications are best to beef up my resume? I've started Q-SYS today but I want to know if I'm heading in a good, solid direction with it. Any advice and help is GREATLY appreciated. I love listening to music and making it. It would make my heart so dang happy to be around it as much as possible. Again, thanks in advance :)


r/livesound • • 5d ago

Question DVS cutting in and out

5 Upvotes

Hi yall! Im using quite an esoteric setup with 3 Dvs devices in my network, two of them take in all 50

channels from my inputs while one works only as a output device for music and other auxiliary stuff, and im only having clock Sync issues with the auxiliary device. its a Windows laptop running ableton live, tried with onboard Ethernet connector and an adapter with no luck. My switches are all Yamaha Dante switches so it should prioritize The Dante packets correctly. Any help is appreciated!


r/livesound • • 5d ago

Question Mixing via Matrix

14 Upvotes

Hi there!

I mainly use the QL1, and recently I’ve started routing my ST L/R to a Matrix.

I started doing this because I usually run my preamp gain around +30 dB or more if needed and I want to maintain a decent signal level going into my Premium Rack processors.

A lot of people have told me that routing through a Matrix allows you to maintain your healthy ST bus level while controlling the overall output volume using the Matrix fader, especially when the overall mix gets too loud.
But I’m honestly quite confused because it feels like an extra step. Why not just lower the ST master fader instead?

Am I missing something here? Is there an actual advantage to using a Matrix this way, particularly when it comes to gain staging?

Thank you all so much!!

Edit: Thank you all so much for the response! Will reflect and work on the signal flow. Cheers!