I've got 5 light sockets outside where I want to use red LED lights. Does anyone have any recommendations? I know it should be easy but I'm looking for a nice deep red color if possible. Some I've seem are a bit on the lighter side of red. Thanks.

Probably a super noob question, so I apologize in advance.

https://www.bhphotovideo.com/c/product/1492249-REG/gvm_800d_rgb_3l_800d_rgb_led_video_studio.html

https://www.bhphotovideo.com/c/product/1490916-REG/gvm_gvm_50rs3l_gvm_50rs_50w_15v_110_220v_3_light.html/overview

Not sure the differences between these two sets.

Which one would be a better choice for 3-point lighting for a youtube video studio setup?

Or are there any other even better alternatives?

Budget - $500 - $1000.

Thank you so much!

i got new led lights the moment i plugged them in the lights were blue. the remote did not work to chnage the colors tho. the remotes signal thing turns red but it does not change the color of the led lights?! any suggestions, i know this happned to alot of other pple

Restoring an original LIGHT BOY for the original GAME BOY. Looking for bulbs that will work, I'm thinking of going LED. The bulb is very small, about 1 mm long. The strait attachment prongs add about another .5 mm. Couldn't find anything about this anywhere. Thanks.

Hey does anyone know if they make or where I can find F21 t5 under cabinet LED COLOR CHANGING bulbs? Trying to get rid of these aging fluorescents and get some smart bulbs that change color for mood, can’t seem to find any online but find it hard to believe they don’t make them. Thanks in advance

i recently ordered an RGB LED strip and turns out it doesn't come with a controller and adapter. i was wondering if there's a way i can use it ?

I am adding lights to a woodworking project and want to make sure I have my components right. I've worked with household LED's and battery operated non-LED's in the past, but this is new to me.

I've got a rectangular work surface just smaller than 2' x 3' with an LED strip (behind frosted plexi) lighting it from the perimeter. I want it to be warm white only, battery powered, and physical controls for on/off and dimmer.

What I think I need is a 5v dimmable WW strip, 3 batteries/holder, and a low voltage DC speed controller between the two. Throw out the controller and remote that comes with most light strips.
Does that sound correct?

Also, the set I am looking at is 2835 chips, not quite 10 per foot. Does that sound like the right amount of lumens for the low to mid range of task lighting?

Some of you will probably find this question naive. I apologize for that.

I really fell in love with the Masterclass way of filming.

I'm currently preparing a similar room and wanted to know what camera equipment and lighting they use?

I have a very flexible budget.

I would even be ok spending upwards to $10k if it means I get the result as close to that.

Currently my only "professional" light is the GVM Led ring light, but it has rather harsh light and I don't look good in it. Far from Masterclass quality. Thinking of getting Aputure.

And my camera? You will laugh, it's an iPhone X.

Any advice regarding the lights and cameras would be much appreciated.

So I want good led lights with a built in defused. I don’t know what to get. Witch one should I get.

I apologize for flooding with beginner questions.

Looking to get a really high quality light for youtube videos.

Would a single Aputure with softbox yield a good result?

I bought a ring Led light, but it seems to be too harsh and doesn't look as nice. I am thinking of using the ring Led light to illuminate the backdrop, but use Aputure for key light.

Would this work?

Or maybe I can just use Aputure for key light and no other lights?

And if I choose Aputure, which light should I choose?

I have a very flexible budget.

Thank you so much!

My led remote isnt working, does anyone know the possible solutions?because ive tried alot.I even changed the battery.The wires are ok.I just dont know the problem.If someone has a possible solution it would be a big help

Hello everyone, I am at the end of my rope with my LED Christmas light strings.

I have 200 LEDs (ws2811) which using a 5a 12 volt 60 watt power supply, 8266 nodemcu.

I get flickering when i connect the 5 volt data line. And thoughts how to stop the flickering(every 4 seconds or so).

I would like to have a least a 4 foot data line.

Hi! I recently got strip led lights. when they’ve been glowing for a while (20-30mins) and i turn them off, they still glow a little. In order to turn the glow off i have to unplug the actual lights from the socket. Anyone else have this issue or know how to make it stop?

I have a 12V PWM Dimmer (linked below) to control six LEDs wired in series in my RV.

The switch appears to require the LED ground to go through it for the dimming to work. The LEDs are chassis grounded, so I haven't been able to get the dimming to work.

Does anyone know why it would require the ground to run through it?

Would a work around be to get a pwm dimmer and put it on the (+) supply line?

https://www.superbrightleds.com/moreinfo/single-color-dimmer-switches/slvdx-60w-3w-led-3-way-switch-and-dimmer-for-standard-wall-switch-box/1245/2916/

I recently just got a new set of led lights they work fine until you set them to white. They turn on and of unevenly it’s really annoying could this be because of the power supply? But I’f so why do the other colours not flicker to?

what are some cheap led lights that are under 30 buxs

Ayo anyone know how to make your LED's like switch through colors, but like you can pick your own colors for them to switch through?

Hi, i have an older keyboard that I'm updating new LED's on. the measured exterior is 2.65mm x 3.1mm and the interior measurement of the solder pads is 1.4mm x 2.3mm. I cant seem to find this size in package form to order on digikey or anything. Does anyone know this size?