r/lasercutting • • 1h ago

Newly completed wall sign for a family member

Thumbnail
gallery
166 Upvotes

Designed with a mid-century theme in mind and made with solid Walnut, Maple, and Mahogany using my 40W Diode laser. Finished with Danish Oil for a natural finish. Final dimensions are 13.625"h x 8.5"h.


r/lasercutting • • 5h ago

Recommendation for Architecture Models

1 Upvotes

Hi I’m in the market to get a small laser cutter to handle thinner objects like 3 ply chipboard, 3/8in acrylic, cardboard, wood, and bristol paper. I make scale models of buildings and would love to save myself some trips to the makerspace by buying one instead. The maximum dimensions would be around 18” x 12” perhaps. Thank you!


r/lasercutting • • 8h ago

Atomstack a70 max

1 Upvotes

Looking for recommendations for what oil and cleaner i should use for the rails and bearings. Been using glasses wipes on the rails to clean dust and the like. Thanks in advance


r/lasercutting • • 10h ago

Power supply(s) look dead on 60W CO2

1 Upvotes

Last week my 7-year-old 60W Chinese red & black stopped firing and I trouble-shot it to find that it didn't like the water sensor so ordered a new one. Up to this moment, the tube has been cutting perfectly, no loss in power or bifurcation that I've seen in previous bad tube scenarios.

During that troubleshooting, I could short the P pin to the G pin, and get the correct LED lights and fan on the power supply, and the laser would fire.

During this same troubleshooting time, only a few seconds later and NOT firing the laser, with the P&G pins still shorted, the LED lights and fan on the power supply went off, as did the lighted toggle switch that feeds the power supply.

I put everything back to normal (no shorts), and did the troubleshooting routine again with the same outcome, no LED's or fan on the power supply. So, I ordered a new one, exact model.

A week later, I have the new water sensor installed, water flowing properly from (and back to) the chiller, installed the new power supply, and I have the EXACT same situation...power supply looks dead, no lights, no fan.

The main machine fuse is fine, but I changed it anyway. The rocker switch for the laser tests correctly for voltage and on/off function.

The 3-pin AC input to the power supply tests correctly for my 120V power.

I read on another thread to test for 5V on the +5V and L pins. Both of these read 0, so apparently that means that the power supply isn't being told to fire. ?.? I don't know where to go from here. What should I check next?

Thanks, All.


r/lasercutting • • 17h ago

First big backlit cutout project.

Thumbnail
gallery
9 Upvotes

First time cutting something this intricate. Ran it on the Aliencell after a couple of scrap tests, the little cutouts on the side pieces needed a push to release but nothing broke. Not fully happy with how the plywood grain shows through the backlight though. So for the next one I’ll sand the face before cutting and try a lighter wood.


r/lasercutting • • 20h ago

Layered Keychains

Thumbnail
gallery
3 Upvotes

Sharing some more layered Keychains I've done for customers and for markets! (NSFW warning last image)


r/lasercutting • • 20h ago

Custom Cork Boards

Thumbnail
gallery
25 Upvotes

I've been having a blast making a handful of Pokemon themed corkboards recently! I made these so I could actually display my pokemon pin collection in a way more stylish/cuter and decor friendly way.

I wanted to share a couple I've made so far. These are 12x12 inches, except Shinx which is a prototype (10x8.5inches). These are hand drawn, then vectorized, cut and hand assembled using wood, cork, and premium felt


r/lasercutting • • 20h ago

New box creation

Thumbnail
gallery
15 Upvotes

Took a plan old box and started modifying. Made of 3mm basswood ply, cut on the Creality Falcon A1 10W, assembled and stained. Not sure about the stain color.


r/lasercutting • • 23h ago

Air filter for 10w laser

1 Upvotes

Considering getting the Bambu H2C, with a 10w laser. They seem to be out of stock on their smoke filter and I’m at a total loss on what I’m supposed to do for filtering the air.


r/lasercutting • • 1d ago

Air intake gaskets

Thumbnail
gallery
45 Upvotes

My favorite aspect about mixing cad and laser cutting is you get all kinds of odd jobs.


r/lasercutting • • 1d ago

Keeping a shallow laser texture visible through paint on a metal watch dial

Thumbnail
gallery
4 Upvotes

I used the laser to put a limewash-like pattern in the face of this dial. The metal I left standing forms the hour markers, logo and the row of letters at the bottom. On a piece this small I wanted the surface texture to be just visible up close.

That made the paint application as important as the engraving. I mixed brown and yellow into white for the warm tone and went gently over the texture so I wouldn’t fill it in. Once the color was on, I exposed the raised metal and polished it. I’m the maker at Rexx. These are two angles of the same piece.

Short video showing the dial in the light: https://www.youtube.com/shorts/85LQmwxjV_o


r/lasercutting • • 1d ago

First laser engraver

3 Upvotes

Hi everyone, I want to get a laser engraver as a gift. They haven't used one before so it need to be pretty simple to use and self contained - we can always upgrade later if they like it. As it's a bit of a "see if they like it" thing, I'd like to keep it relatively low budget - around £350 max. What would recommend?


r/lasercutting • • 1d ago

3d prints that have made your life easier?

12 Upvotes

I am new to the community and excited for my machine to come. I have a 3d printer, was wondering what prints have made laser cutting easier for you. Also open to any other recommendations.

Thanks!


r/lasercutting • • 1d ago

laser recommendation for cutting rubber

3 Upvotes

I’m looking for a laser cutter capable of cutting 1/4-inch rubber gaskets(neoprene), acrylic, and occasionally engraving aluminum and other plastics.

I’m new to laser machines, but I’m mechanically inclined and comfortable with setting up and maintaining equipment. I’ve been looking at the OMTech 90W CO₂ laser.

Does anyone have experience with this machine, or would you recommend something else for these applications?

Thanks in advance!


r/lasercutting • • 1d ago

Christmas calendar project

Thumbnail
gallery
15 Upvotes

Christmas is close, you can countdown with this Christmas calendar.

Designed for 3mm or 4mm material thickness


r/lasercutting • • 1d ago

TruTops users: how do you import marking lines and pre-nested sheets from other software? (+ Bodor .ncex question)

0 Upvotes

I'm working on export from a nesting program and trying to get the file handoff right. A few things I couldn't find documented anywhere:

  1. Marking on DXF import: which colour or layer does TruTops (Laser / Boost) treat as marking/engraving instead of cutting? I've seen "yellow" mentioned. Is that a default or something each shop configures?

  2. Marking inside a .GEO: if you save a part from TruTops with one line set to marking, how is that line stored? If anyone can describe or share a tiny .geo like that (a square with one marking line), it would help a lot.

  3. Pre-nested sheets: can Boost take a whole-sheet DXF that is already nested elsewhere and generate the LST while keeping the nest, or do you always re-nest from single parts?

  4. Third-party LST: anyone running LST files written by non-TRUMPF software? Do you let the control do kerf (TC_LASERCORR_ON) or offset the path?

  5. Bodor: does anyone know what a BodorThinker .ncex file actually is (zip / XML / binary)? Can other software produce it, or is DXF the only way in?

Any pointers appreciated.


r/lasercutting • • 1d ago

Bambu Lab R1 vs. xTool X1 for long wood pieces and chipboard?

7 Upvotes

I’m trying to decide between the Bambu Lab R1 and the xTool X1. My main use cases are:

  • Cutting wood pieces up to 1000 × 150 mm, so I’ll need a conveyor feeder.

  • Cutting and engraving 1–3 mm Finnish wood pulp board (Finnpappe).

  • Getting into acrylic cutting. I haven’t worked with acrylic yet, and that’s the main reason I’m looking at CO₂ lasers.

I currently have an xTool S1, but the conveyor feeder for it has never been available here in Germany. This time around, being able to actually buy the feeder matters just as much as how well it works.

The R1 would be almost €800 cheaper for me. If you’ve used either machine with its conveyor, how reliably does it feed meter-long pieces and do you see any alignment issues where cuts continue after the material advances? I’d also love to hear from anyone who’s cut or engraved Finnpappe on either machine.

For this kind of work, would you save the €800 and go with the R1 or is there a good reason to pay more for the X1?


r/lasercutting • • 1d ago

A few metal jewelry projects I've been making with my fiber laser

6 Upvotes

I've been making custom metal jewelry for a while now, mostly taking on smaller orders for personalized pieces. I used to do a lot of the engraving and shaping by hand, which could take quite a bit of time, especially when I had several orders to work on at once. I eventually picked up an xTool F2 Ultra late last year because I wanted to try more detailed designs and make the whole process a little easier.

Since then, it's become part of my regular workflow. These are three types of jewelry I spend the most time on.

  • Personalized metal bracelets

Bracelets are probably my favorite pieces to work on right now. I often browse Pinterest for inspiration, especially floral and botanical patterns. Most of my custom orders fall into three styles: names or dates, simple symbols like stars and hearts, and more decorative designs with flowers, leaves, and other details.

The floral designs seem to get the best feedback from customers. I usually take patterns I like and resize or adjust them to fit the bracelet. The 60W MOPA on the F2 Ultra has been really useful for this. It brings out a lot of detail on the metal without requiring me to simplify the designs, and I also enjoy experimenting with different color marking effects.

  • High-temperature enamel earrings

These take a little more work since there's more involved than just engraving. I usually start by designing the overall shape of the earrings, then engrave the patterns onto the metal blanks and cut out the outer shapes. After that, I do the enamel coloring and firing separately.

This was actually one of the projects I was most excited to explore from the beginning. I started with three pairs as a small test batch before moving on to finished pieces. The 60W MOPA handles both metal engraving and cutting, so I can make the metal blanks myself without needing separate machines for those two steps. When producing multiple pairs of the same design, I can reuse the same design files and processing settings, which helps keep the shapes and patterns consistent across the batch.

I usually do around 5–7 pairs at a time, and the results have been really nice. The enamel stage is where I get to play around with different color combinations. Lately, I've been into that fluid look.

  • Custom initial necklaces

Another regular order is personalized necklaces with connected initials or names. Customers send me the letters they want, and I turn them into a connected design that can be cut out of metal to make a pendant.

These can be a little tricky because everyone's name is a different length. I often have to adjust the font, spacing, and how the letters connect so the pendant looks balanced without the connecting parts being too thin or fragile. The dual cameras on the F2 Ultra have been pretty helpful when positioning these smaller designs. I can preview where the design will go and make adjustments before starting the job.

There's still plenty of room to experiment with different fonts and ways of connecting the letters. It's interesting how much the final pendant can change just by switching up the lettering.

Overall, I'm really happy with what the F2 Ultra has helped me accomplish so far. I originally got it mainly for metal jewelry, but now I'm already thinking about other materials and more types of personalized products. There's still a lot I want to explore.


r/lasercutting • • 2d ago

Cutting wood on xTool M2

2 Upvotes

Has anyone had luck cutting 1/4" hardwoods with the xTool M2? Usually doing these on the CNC but looking at adding a laser to the roster and wondering if the M2 could handle it. Appreciate any feedback!


r/lasercutting • • 2d ago

Lasers for pen inlay cutting?

5 Upvotes

I would like to cut inlays for pen turning, like in this example, in both woods and cast acrylics. I think an RF CO2 or diode laser would work best for this, and the options I've investigated are 50 W and 40 W, respectively. The lower price and smaller dot size of the diode laser are attractive, but I wonder if it will mangle any clear epoxy pours. Advice, recommendations, and links to similar discussions are greatly appreciated.


r/lasercutting • • 2d ago

Cracked Laser Follow Up

Thumbnail
gallery
0 Upvotes

Same crack as before. Standard settings. Nothings changed.

In the last 9 days, this machine has seen 150 unique appointments.

I'm fully expecting down votes because I know what I'm doing is very much frowned upon. This whole display has been me sharing what we've learned is possible when you're struggling.


r/lasercutting • • 2d ago

Heyyy!

0 Upvotes

So I'm in a bit of a pickle and need some help.

I bought yesterday xTool M1 10w (it was 300£), I kept comparing with xTool M2 10w (color print & cut - 529£). For some reason the entire night I kept thinking I'm an idiot for not going for the machine that can print. Is it that big of a deal? Need to mention that the creative part has no limits, so I'll use it for random things (adhd and debpt are on).

Also, decided to make this post as I just realised that the M1 doesn't have a pen holder either, are there any unofficial pen holders or anything?

The machine should arrive tomorrow (as dpd was very nice today). What should I doooo?


r/lasercutting • • 2d ago

Heeeeeeere's Johnny!

Thumbnail
gallery
45 Upvotes

9mm deep river rock engraving done with 60w mopa fiber laser and a lot of time.


r/lasercutting • • 2d ago

190W Laser Gun?

0 Upvotes

I came across this. Unless it's AI or false it's claiming it is a handheld laser in a gun shaped case that is outputting 190W.

https://www.reddit.com/r/interestingasfuck/comments/1xzsarw/this_is_what_a_190watt_handheld_laser_pistol_can/

How are we limited to 10-40w on bench laser cutters if this things exists?


r/lasercutting • • 2d ago

My first time trying to lasercut an image but turned out good

Post image
13 Upvotes

Gonna 3d print wheels and make it like a tech deck