r/gunsmithing • u/NoticeVisual1656 • 8h ago
Can anyone help?
Where do I file this trying to fit a grip and I'm lost it's a personal project so just looking for advice?
r/gunsmithing • u/NoticeVisual1656 • 8h ago
Where do I file this trying to fit a grip and I'm lost it's a personal project so just looking for advice?
r/gunsmithing • u/Dangerous_Walk9239 • 3h ago
So I bought this screw stud set, but I’m not quite sure how to put them in there and have them stay when the hole is not threaded and the screw themselves don’t look pointy enough for me to drill into the wood or are there special tools that I need before inserting those studs? Thanks in advance!
r/gunsmithing • u/Feeling_Title_9287 • 1h ago
Original Marlin Ballard No.1 1/2 Hunter's rifle 45-70
r/gunsmithing • u/Giganticsquid3 • 4h ago
To preface I have surface level knowledge on the construction of firearms but I do have mill and lathe experience. One of my favorite firearms is the Panzerbüchse 39, however I would never buy one for a couple of reasons, specifically the round, price, and size. I inherited a myriad of firearm parts and was thinking about cannibalizing this incomplete winchester 70-30-06 Springfield pictured below and then designing and machining a falling block like the one on the PzBh 39, not necessarily to create a replica but to create something aesthetically similar. My question is, is it a bad idea to use parts from the winchester? Should I just design and build everything from scratch? My concern with a fully scratch build is that I don't have the tools to rifle a barrel and it would cost significantly more. Also, as far a technicalunderstanding goes, where should I start learning about how to do this and safely at that? Thank you.
r/gunsmithing • u/Desperate_Fall367 • 4h ago
Hello, picked up a Stevens 311 and been trying to clean it up and swap parts that are worn down. In the process a few things fell off or broke. Also the stock sounds hollow on one side, I imagine it could be rotted or something? In the end I couldn’t get the barrels off. Followed instructions, used degreaser and cleaner on everything hoping it would get free but nothing. I can dry fire it, cock it etc but no luck on disassembling it further. I ordered a new cocking plunger since this one snapped. Any help would be appreciated.
r/gunsmithing • u/Ok_Calendar_7626 • 5h ago
Here is my problem.
I have a CGW pro kit installed, KMR SAO flat trigger and Eeman Tech ultimate competition hammer. My main spring is 8lb and i have also polished the internals slightly.
Now my trigger sits at 2.5lb. Which feels amazing, but the minimum trigger pull for 25m national handgun competition in my country is 3lb (1.360 g).
I have tried replacing the main spring with a 9lb one, but that puts my trigger way above 3lb. I just need that 0.5lb to get my trigger pull into the competition regulation limit.
r/gunsmithing • u/Existing-Gas9048 • 1d ago
Found out the barrel of rough rider 22s are 1/2x28, and had the end of a scrap ar15 barrel. Biggest "gunsmithing" project I've done to date, with small hand tools only. Not very confident in the accuracy or my halfassed forcing cone, but this was never a reliable gun anyway
r/gunsmithing • u/CountyHermit50 • 6h ago
I am no Gunsmith by any means. Does anyone know what this piece/part is called inside the Redhawk's frame? When the trigger is pulled, instead of coming straight to the frame's rear, it bends to the left.
r/gunsmithing • u/Gold_Temperature_329 • 22h ago
NOT A GUN SMITH. Looking for advice on 7mm-08 Browning X-Bolt. Casings were getting stuck and bolt unable to be cycled. Inspected and found rust and pitting inside chamber. Assuming case expanding into pitting causing stuck casing. Inspection after thorough cleaning still shows rough surface but also revealed what looks like a crack inside of the action(inner/upper) prior to chamber. With the combination of issues lead to the trash can or a reputable smith? Thanks for any and all advice.
r/gunsmithing • u/phat_tendiez • 21h ago
I bought a new barrel and silencer for my Ruger 10/22. The silencer is a Polite Society Temperance 22.
The barrel and silencer do not want to thread together smoothly. I probably cranked on it harder than I should have and want to get the threads on both inspected and cleaned up. Is this something a gunsmith would be willing to do on a suppressor? Or is this something I could clean up with a 1/2-28 tap and die?
r/gunsmithing • u/Maine_man207 • 1d ago
Made up a 5.5" barrel band barrel to go mate up to the cylinder I fixed the endshake on. Barrel was turned between centers on my South Bend 13. Marking which jaw the lathe dog engaged on let me take it in and out of the lathe to check the thread fit and not have to pick up the thread. The barrel band is located to be an integral recoil lug for the ejector rod housing, so no shear stress on that little 8-36 screw. Crown was checked with a Q tip for burrs. This is the first barrel I have made from a blank. I like the looks of the revolvers the Linebaugh and Bowen would build, so this is heavily inspired by what they did.
r/gunsmithing • u/Next_Carpenter_8827 • 1d ago
r/gunsmithing • u/ForceUseYouMust • 1d ago
r/gunsmithing • u/cameronflip • 1d ago
I got this echelon from a friend and he tryed to install a tyrant CNC trigger and it is extremely sticky won’t reset or move freely and the alen screw is striped on the trigger
r/gunsmithing • u/Unknown_Professor4 • 2d ago
It’s a long story. My father in law died unexpectedly and this 1995(ish) stainless K frame was in his safe. However, it had obviously been run over by a truck or something very kinetic occurred. The cylinder was deflected by about 15 degrees, yoke bent, ejector/center rod bent, cylinder lock sheared off. Back side broken, grips crushed. Over the past few years, I’ve picked up parts and done some polishing. I need to find a gunsmith to test it and ensure the last few parts are properly fitted. If it gets a clean bill of health I’d like a few performance mods, maybe some engraving, to give to his grandson. I need to make a checklist of what should be evaluated. Any suggestions or thoughts are appreciated.
r/gunsmithing • u/TieDo18 • 1d ago
Hey all,
So I have been trying to get a flash hider off of a PSA Jackel it was pinned and welded, so I dreaml out the pin. And I thought it was tight. I look and there appears to be rocksett on it along with the pin and weld. Anyways, fast forward 12 hours of soaking in water I cannot get the damn thing off. And after asking the customer if he was in love with the factory flash hider he said no. So I started grinding it off...
Anyways I am at ends with how to get it off. I have taken MDs off no problem, but this is a first...I'm just looking for ideas or solutions to get this flash hider off. Thanks
r/gunsmithing • u/monsieurLeMeowMeow • 1d ago
r/gunsmithing • u/Cultural-Rooster1227 • 2d ago
I have been looking at lathe for quite a while and came across this South Bend heavy 10 lathe for sale locally. With the included accessories and tooling would this be a solid purchase?
r/gunsmithing • u/creakymoss18990 • 1d ago
Hello! Never posted here and I'm very new to firearms in general so apologies if I am not saying stuff right.
Photo 1 is what its supposed to look like (manually pushing it into correct position) and photo 2 is where it is, and photo 3 is a big red circle around the issue.
Due to this misalignment the left shell latch would not disengage and therefore cartridges are not being let out from the tube.
How this works is the rail on the pump has this little ramp the pictured metal piece is supposed to get pushed up onto sliding onto the left side of the rail (on the outside) allowing the next cartridge to cycle.
However this metal piece is bent/positioned >1mm downwards causing it to ever so slightly not be flush on the metal so the ramp hits the middle instead of scooping it up.
I came up with 3 options and I want to run it over with more people than myself.
1 File the shell latch into a ramp so I don't need to mess with anything and they will just ramp onto each other. I could also do some gentle de-burring while I'm at it (definitely plenty of factory burs lol). But the big downside is I'm taking off material and I don't want to mess it up further.
2 Put a very small something (thin layer of solder?) under the shell latch in a place where there are no moving parts so it sits high enough to get caught by the rail ramp (there are plenty of spots, it widens a lot after this metal piece and the tolerances on this gun are low) but I don't know what I would put on it that would stay put permanently. I can also wedge something under it which would work as well but again isn't very permanent.
3 Get it replaced/repaired professionally. Frankly I don't want to do this for financial reasons and also I like fixing my own stuff.
r/gunsmithing • u/Random-American- • 1d ago
I have a pre 2020 reminton 700 action(short action). I used a oversized recoil lug and headspaced the barrel. I've been having issues with the bullet hitting the barrel. Do I need to use a smaller recoil lug or should I shave the feed ramps down? The barrel is a shilen rem/age with the lockn nut. Nogo, go, and field gauge all are within tolerances. I made the headspace pretty tight as well so its on the lower end on the go gauge
r/gunsmithing • u/CaptainN0053 • 2d ago
Browning hi Power had the front sight pop off while I was at the range, Ive spoken to several gunsmiths around me about soldering one of these new sights on and everyone keeps giving me deer in the headlight looks. Has anyone ever done one of these before ? Does anyone know someone I can mail this too to have the work done? Thank you very much
r/gunsmithing • u/V7I_TheSeventhSector • 2d ago
I am NOT making a real gun
im not a gun smith, just using a passion project to learn how to design mechanical systems
im trying to learn how multiple levers interact with each other but ive gotten stuck?
what should happen, is the bolt goes back, pushes the dog down and when the bolt goes forward, it pushes on the dog tooth and that forces the lift up, but for some reason when the bolt goes backwards, it pushes on the dog and that in turn pushes the lift up too early?
ive tried changing the location of the spring, both pivot points and basically everything i can think of but nothing seems to work?
worst part is, because of this, the lift is not going up high enough and is causing a number of problems with feeding and cycling?
r/gunsmithing • u/SamuelaMaestro • 2d ago
I had to do some fine work with my colt lightning sear and guess what... Cant find it... Need help, cant order it from US (am from europe) does anyone has one that you Can measure and mby dm me?
I would pay with gold 🙏🙏🙏
r/gunsmithing • u/Burt-Macklin-26 • 2d ago
I’m sorry if this isn’t common knowledge but I’m new to compensators. I bought the griffin armament micro comp. It says it needs to be torqued to 8lbs. What tool should I be using to ensure I properly torque it to 8lbs. Do I use a socket set, on a wheeler wrench set to 8lbs, from the muzzle side? Do they make a crescent set on a torque wrench? I know wheeler is a brand people suggest but I’m unsure what size I need to buy and what product I should be looking at. Thanks in advance for any help.