r/diyaudio • • 13m ago

Finished my dual 8

Thumbnail
gallery
8 Upvotes

Just finished my dual 8 subwoofer. Drivers are ground zero gziw series. I added new dustcap on them to look more plain. Its tuned to 36hz, if i block one port, its tuned to 25hz. I use PA speakon connector so its easy to unplug it if I need the space in the back of the car, or if I want to use it in social hangout settings which I do once in a while.


r/diyaudio • • 46m ago

Custom Acoustic Panels

Post image
3 Upvotes

r/diyaudio • • 1d ago

First Build: OB, Brazilian lacewood, steel wings with a Woofer Assisted Widebander.

Thumbnail
gallery
406 Upvotes

This is my first loudspeaker project: an open-baffle system built around a Lii Audio Crystal-8 (the red version, which I rarely see posted around) and a SB Audience BIANCO-12OB150-01 , with digital filtering and bi-amplification. After about a year, the design is fairly settled, while the electronics are still evolving.

I’m a photographer by trade, and the project started when my Klipsch RP-600M II developed an irritating tweeter buzz. Off-the-shelf speakers are expensive in Brazil, so I went down the DIY rabbit hole and started sourcing components.

I call it Painel Sonoro Oito-Doze, Portuguese for “Eight-Twelve Sound Panel.” It’s actually a DIO—do it ourselves—project: I had help from two friends, a carpenter/furniture designer and an architect, with the wooden fronts and metal fabrication drawings. I also learned a lot from lurking here (so in the spirit of giving back, here's my report).

The main influences were Leon Huijgen’s early open-baffle work, Decware’s Zen Master series, PureAudioProject, and builds shared by other DIY enthusiasts. There’s an obvious resemblance to the PureAudioProject Duet, although mine uses less expensive components, a different side profile and a heavier baseplate.

The 8-inch Crystal-8 handles the full range, running unfiltered, with no high-pass. It has a paper cone and a 25 mm voice coil; published parameters include Fs of 37.5 Hz, Qts of 0.625 and Vas of 120 litres. It’s rear-mounted, with a smooth roundover around the cut-out. It's attenuated by 8db to level match.

Below it, the 12-inch SB Audience woofer supplements the bass. It’s designed for open-baffle applications, with a coated paper cone, a 60.5 mm voice coil and published parameters of Fs 41 Hz, Qts 0.68, Vas 80 litres and Sd 530 cm². It’s flush-mounted on the front.

The wooden fronts are louro-faia, commonly traded as Brazilian lacewood. Its pronounced ray figure gives it that distinctive flecked pattern against a brown to reddish-brown background. Appearance was part of the choice; I’m not attributing a particular sonic benefit to the species. They are 480x920x20mm.

The steel side wings form a U-shaped baffle around the woofer, tapering to a shallower profile around the Crystal-8. This extends the front-to-rear acoustic path mainly in the woofer section. The calculated cavity resonance is around 343 Hz, above the woofer’s 250 Hz low-pass setting, though the gentle filter slope won’t eliminate excitation at that frequency.

We made two prototypes to work out the proportions, cut-outs and mounting details before producing the final fronts. The woodworking took considerable effort, but I believe it's the main point of attraction of this design.

The signal chain is:

WiiM Ultra → Raspberry Pi Pico 2 / RP2350 running DSPi → two PCM5102 DACs → two AIYIMA A07 Max amplifiers → speakers

The two DACs provide four analogue channels for the stereo full-range and woofer sections, with DSPi handling routing and filtering. Its support for multichannel digital output on RP2350 hardware makes it useful for this kind of setup.

The woofer receives a first-order Butterworth low-pass at 250 Hz, giving a 6 dB/octave asymptotic electrical slope. Since the Crystal-8 remains unfiltered, there’s broad overlap between the drivers, and their acoustic sum depends on the mounted responses, relative levels and phase. The woofer also doesn’t relieve the Crystal-8 of low-frequency excursion; trying a high-passed alternative is on my list.

For now, the electronics are still boards and wiring in a cardboard box. It’s convenient for experimenting, but the packaging has some catching up to do with the speakers.

My main listening reference was Keith Jarrett’s trio recordings at the Blue Note in 1994. Jarrett probably accounts for 80% of my listening, so I started with music I knew well. Those recordings sounded encouraging, but the bigger surprise was when I listened to other albums with strong vocal presence: Patricia Barber singing Miss Otis Regrets, Tracey Thorn and Everything but the Girl, Nick Cave Boatman's Call, Milton Nascimento's angelical voice on Angelus and vocal works by Philip Glass (Songs from Liquid Days) and Arvo Pärt (Stabat Mater, Lamentate).

What I enjoy most is the spatial presentation: music feels detached from the panels, with substantial stage width and depth, and clearly positioned performers. As a photographer, I find myself thinking about how sound, like light, changes the way a room is perceived.

This is a system for sitting down and listening, alone or with a few friends. It gets loud, but high output and uniform coverage around the room weren’t the goals, and deep sub-bass isn’t its strength.

I have a measurement microphone and will gather measurements soon. Next comes refining the driver integration, giving the electronics a proper enclosure or creating a dedicated crossover.


r/diyaudio • • 1h ago

Help making a sub box for mini cooper

Thumbnail reddit.com
1 Upvotes

r/diyaudio • • 1d ago

Homemade Triatrix horn loaded monitors with concrete Ball bass

Thumbnail
gallery
87 Upvotes

80w Valve driven horns, (tweeter, upper mid range, lower Mid range).
200w transistor bass amp. Bass Ball 2 inch thick concrete 8.75 cub ft. volume.
Clean down to 19Hz..
Studio for production of video composition for soundtracks studio.


r/diyaudio • • 13h ago

Hifonics Zeus zxx2400.1d

Post image
6 Upvotes

Hooked the bass knob and wire up. (Came in the box with it) lost all bass. If I turn the bass up on the head unit it works but barely metering at the speaker terminals I get like 3 volts.


r/diyaudio • • 3h ago

Clipping circuit + indicator for DI box?

Post image
1 Upvotes

Hey, all! I've been working on this project for a while now. It is a circuit that contains both a DI box + a ReAmp box. The idea is that this would work like a looper for processing audio using guitar pedals as "hardware" for music production. The ReAmp box has a switch that cuts everything below ~100Hz and everything ~7kHz.

I want to add a clipping circuit + detection to the DI box side. I have a few spare VU meters that I could use for that, but LED indicators would work as well. Does it make sense? Is it practical? What circuit could I use for that?

Thanks in advance!


r/diyaudio • • 1d ago

Found it the dumpster today, so happy

Thumbnail
gallery
120 Upvotes

6 ohms minimum tho, what would happen if i feed it 4 ohms woofers?


r/diyaudio • • 8h ago

Simple solution just 3d print the pod

Post image
0 Upvotes

r/diyaudio • • 11h ago

DIY cover for the DIY mic

Post image
0 Upvotes

r/diyaudio • • 11h ago

Niles Audio SVC-4 Creative uses?

Post image
1 Upvotes

The device allows switching between 2 different amps and 4 speaker pairs. I think I’ll try using it to switch between room speakers vs near field speakers while using the same powered sub. Anyone else using one? What kind of setup?


r/diyaudio • • 1d ago

My Second Attempt at fully 3d printed electrostatic headphones. Silicone foam earpads were massively improved vs the previous model. Very happy with the elastic band adjustment mechanism.

Thumbnail gallery
36 Upvotes

r/diyaudio • • 19h ago

DIY Desktop Soundbar with Tang Band Modules

2 Upvotes

Dear all,

i recently purchased a cheap 2.1 soundbar for under monitor desktop use, it is an ultimea poseidon m20 pro.

I looked for more "popular" brands with similar products but could not find any, when, they were much bigger.

Now I was just web surfing and somehow came across some tang band modules and I think it should be possible to arrange something that has similar dimensions to the soundbar mentioned above, but I hope would sound much better.

It would consist of:
1x Tang Band T3-2190S woofer module
2x Tang Band T1-1815SA full range modules
1x amp module
1x PSU modue
1x DIY enclosure

So the woofer would be in the center and down facing....left and right the two full range modules.....behind those 1 PSU unit on one side and one AMP-Unit on the other side....
All in an enclosure around 45 cm wide, 14 cm deep and 7 cm high.

It would be essentialy something like shown in this video but nicely mounted in a DIY wood enclosure: https://www.youtube.com/watch?v=kg6Eqdx6XbI

The only connection I would need is aux to pc (or rather monitor output)

I think it could be within 200 bucks.

I had a pair of KLIPSCH RP-600M in the past and there were all I needed...I had to get rid due to not having enough space anymore....and since I can consume media at my desk only and don't want to wear headphones all the time, I was looking for a small soundbar with some capability to reproduce bass.

So what do you think, would it be worth the hustle or would I be disappointed in the end.


r/diyaudio • • 20h ago

Blindly attempting to make a pair of inductors.

2 Upvotes

I am working on recreating the crossover for a pair of Paradigm Titan V1 speakers, as the original components have been lost. I have some concerns regarding my current approach and would greatly appreciate your expert advice. I plan to rebuild the speaker cabinets and refurbish the units entirely, though I have limited resources and equipment available. I have already refoamed the woofers using generic parts and am now attempting to build an inductor by hand, using the "I" part of an "E I" transformer/inductor.which has led me to question if this is a viable path or if there is a more practical alternative. Given my current lack of specialized tools like an LCR meter and the constraints of my situation, could you please provide guidance on whether this is a feasible project or if I should consider a different strategy? Any information or assistance you could offer would be sincerely appreciated.


r/diyaudio • • 16h ago

What should a tool-free, "can't plug it in wrong" module slot in an integrated amp look like?

1 Upvotes

Thought experiment for my thesis: a midrange integrated amp where the user can swap the streaming board or DAC without tools, with a connector that can only go in one way (poka-yoke).

From experience:

  • What would you insist on? Connector type, USB, separate rails, grounding/shielding, ...?

  • Which parts fail most in amps you've repaired?

  • Or is this a terrible idea from a noise perspective?

  • What can you do when the software has developped a fault?

I have a separate repairer track in my survey (first comment) if you want to help further.


r/diyaudio • • 1d ago

First DIY Subwoofer

Thumbnail
gallery
87 Upvotes

Built with my dad's old sub from when he used to build speakers both for work and as a hobby.

41"x18"x16"

House shaking on barely half power, super pleased with how it turned out


r/diyaudio • • 1d ago

Boombox

8 Upvotes

I've seen other people making these on this sub and they look fun. Not audiophile or anything, but great when I go to the beach or somewhere else that I don't want to take a nicer speaker. Sounds loud and clear all the way up. Parts all sourced from Amazon except the wood scrap which I had lying around from a project I did a year or two ago.


r/diyaudio • • 1d ago

Rehoused Denon DP-1000

Thumbnail gallery
5 Upvotes

r/diyaudio • • 22h ago

So, I went down another audio rabbit hole...

Thumbnail reddit.com
1 Upvotes

r/diyaudio • • 1d ago

Ended up with 5 KEF Ci 160QS Ceiling speakers...

Thumbnail
gallery
6 Upvotes

What would be a good DIY for these? Seem like good drivers and were expensive.


r/diyaudio • • 1d ago

Speaker recommendation

1 Upvotes

Looking for recommendations for front stage speakers for my 2022 Yukon. I want an SQ setup with clean, clear vocals and crisp sound. What do you suggest if I'm running active?


r/diyaudio • • 1d ago

Need help selecting speakers

1 Upvotes

Looking for recommendations for front stage speakers for my 2022 Yukon. I want an SQ setup with clean, clear vocals and crisp sound. What do you suggest if I'm running active?


r/diyaudio • • 1d ago

My custom 2.1 Bluetooth speaker build.

Thumbnail
gallery
45 Upvotes

Hey everyone!
Wanted to share my latest DIY audio project – a custom 2.1 Bluetooth speaker I built completely from scratch.

Build Specs & Materials:
Enclosure:12mm (1/2") plywood box with a 15mm solid pine front baffle
Dimensions: 43cm (W) x 23cm (H) x 18cm (D) / 16.9" x 9.1" x 7.1"
Configuration:2.1 Channel (Isolated left/right chambers + center subwoofer chamber)

Drivers:
Left & Right: 3" full-range drivers
Center Sub: 4" woofer paired with a rear-firing 5" PR

Amplifier : TPA3116D2 2.1 channel amp board
Inputs :Bluetooth + 3.5mm AUX input
Details : Hand-cut and hand-stitched leather carrying handle on top

Thanks for looking!


r/diyaudio • • 1d ago

Portable stereo

Thumbnail
gallery
15 Upvotes

Been working on a project that needs to have portable speakers, so I got some drill batteries to power a car stereo that uses the rear channel to power the woofer, and the fronts to power the mids and highs, all with filters of course. The totes are just temporary but honestly I really dig how they look, lmk what yall think!