r/cruze • • 6h ago

HELP. Issues after 3.4 cruzekit install

2 Upvotes

I installed the 3.4 chevy cruzekit. After the install I started the.car and there was no air blowing out of filer cap and engine sounded as it should. I took it for a test drive and white smoke was coming out the exhaust. Took off the.oil filler cap and now there is air pushing out the oil filler The black plug is still seated in the manifold. All new parts were installed when installing the cruze kit including the purge and new pvc valves were used as well as the valve to the turbo. Any help would be appreciated. It ran fine before the.kit install with the exception of bad pcv hose and the purge valve was bad.


r/cruze • • 10h ago

I need some help with my Cruze 2011

Post image
2 Upvotes

Hey Cruze fam! I know a Cruze probably wasn't the smartest choice for a first car lol, but it’s mine now, it’s basically my baby, and I really want to learn how to properly maintain and fix it.
I’m dealing with a weird starting and electrical issue, and I’d love some input from people who know these cars well:
The Symptoms:
Intermittent hot-start and cold start issue: After driving (anywhere from 10 minutes to a couple of hours), parking, and trying to start the car again, it fails/struggles to start**,** sometimes it happens in the morning for the first start it struggles as well. However, if I let it sit for a while or I move a lil bit the fuse box, it starts right up with no issues.
Dashboard lights: Multiple warning lights are currently on.
What’s Been Checked So Far:
Battery: Tested by a local tech and came back completely fine.
Alternator (Overcharging): It’s spiking up to 15–16V, which the tech warned could damage the battery or fry other electrical components (and I know these cars are super sensitive to voltage issues).
Other suspects: The tech mentioned that fixing the alternator might not solve the hot-start problem on its own, and someone** else **suggested it could be the fuel pump.
Questions for the Community:

  1. Is this a common issue on the Cruze?

  2. What ended up being the actual fix for you (alternator/voltage regulator, fuel pump, ground cable, sensor, etc.)?

  3. Once it’s fixed, is there anything I should do to prevent it from happening again?

I am algo changing very soon the spark plugs I just ordered the 4 original GM spark plugs online so I can replace them.

Any advice would be hugely appreciated**!**


r/cruze • • 11h ago

Intercooler air inlet hose?

Thumbnail
gallery
3 Upvotes

Was looking for the drain plug for the coolant and come across this. It’s gunky with oil. Not sure what is going on…O ring? Read something about PCV issues as well. Not sure what’s going on or the last time all of this was checked and maintained.


r/cruze • • 1d ago

Gen1 - Mechanical What could be causing this? 2011 1.8

Thumbnail
gallery
1 Upvotes

It doesn’t give the engine light so I assume it’s a pending code or something but idk why it happened


r/cruze • • 1d ago

Battery voltage on my 2012

2 Upvotes

So I replaced the alternator and the battery a few months ago. Currently struggling with a P0420 code, but today I noticed my voltage had dropped to 12.5 while driving. It would come up a little to the low 13's but stayed mostly in the 12's. After the car sat off for about 20 minutes it jumped up to 14.5 but once driving it dropped again. Should I be concerned with this?


r/cruze • • 1d ago

Undertray finally bit the dust.

Thumbnail
gallery
1 Upvotes

I finally ran over something that took out most of the insulated tray under the engine. There was a deer carcass in the middle of the road just over a hill. There was a car oncoming so I couldn’t swerve around it. You can see from numerous metal plates on the tray, it has been hit and repaired in the past.


r/cruze • • 1d ago

Gen 1 1.4 Turbo coolant leak

Thumbnail
gallery
3 Upvotes

I've previously replaced the radiator and all the coolant hoses. The leak has now migrated to this point. Can anybody tell me what part this is and what it takes to fix it. The first photo is the general area reference, the scond is a close up of where the leak is.


r/cruze • • 1d ago

2014 1.8, oil disappearing

2 Upvotes

I have a 1.8 was about 154,000 miles on it. Earlier this year I noticed oil levels were low and the oil filter looked completely crushed. I change my own oil and do it around 4500 to 5000 mile intervals. after finding the oil filter looking like that, I replaced the oil cooler thinking that the excess heat caused it to do that after the oil cooler replacement I am still having oil disappearing about a quart every thousand miles. There’s no sign of a leak on my driveway. I’ve noticed a small drop on the bottom of the AC compressor bolt, which then drops onto the subframe. Has anybody else had this issue and what did you do to fix it? Thanks in advance.


r/cruze • • 2d ago

Gen1 - Mechanical Now it finally happened. 🤦‍♂️

17 Upvotes

So far everything was going great. Coolant issues have been resolved 😉! Checked oil 2 weeks ago and that was 2 weeks after I did an oil change and it was down a quart. Ok, no biggy. Drove it like I own it. Started smelling oil once in awhile and sometimes in 3rd and 4th gears I would lose some acceleration. Would look under the hood and no signs of oil leaks. Checked oil today and down a quart again. WTF!! So I googled up some stuff and I didn't realize there is a secondary PCV valve on the backside of the engine 🤯🤷. So I took off that hose and looked down the hole and there was no orange (or any color) valve visible in the hole. So now I have to get me a Cruzefix.


r/cruze • • 2d ago

Cooling issues

2 Upvotes

I’ve got a 2016 Gen 1 LT and it’s been in for overheating 2 times. This time it’s different. My fan will start going at almost ludicrous speed, and my temp gauge will dance around at normal then will peg full hot then dance around normal. I have looked to see if I am eating coolant and it doesn’t appear to be. On my 2015 Silverado it was doing almost the same thing but the temp gauge was full cold and it was the coolant temp sensor. Has anyone else had the same issues, and what was your fix.


r/cruze • • 2d ago

Gen1 - General Sad to say the cruze has died

4 Upvotes

Oil was green, coolant had gotten into the water. my coolant resivoir would be full, overheat would happen and it gets DRAINED, metal in my oil, looked like moss may of grown in my cruze. and lastly overheating caused coolant or water to EJECT tf outta the hood and onto my windshield


r/cruze • • 2d ago

Gen2 - Mechanical Not sure what this leak is

Post image
4 Upvotes

Hey there y'all. Having issues with my Cruze again (what's new), and while I was checking things out I saw this leak coming out of my car and im really not sure what it could be. There's no hints of what it is, it's almost colorless when wiped with a paper towel and doesn't smell like anything. Any ideas?


r/cruze • • 2d ago

Gen1 - General I have a bit of an update

4 Upvotes

So my parents have told me they are buying me a 2014 Chevrolet Cruze LTZ, it happens in May of next year, what should I know about this cruze?


r/cruze • • 2d ago

Gen1 - General is this normal when a engine overheats?

5 Upvotes

r/cruze • • 2d ago

P00016 P00011

Post image
2 Upvotes

So I just got done doing a timing cover gasket on my 2013 Cruze 1.4 turbo. During that process I replaced the old VVTs and camshaft sensors. When I had everything reassembled I took it for a drive and everything was fine. Now I’m getting the above codes for camshaft position sensors. Engine isn’t running sluggish or rough. When I unhooked the battery to check my sensors and reattached it, the codes cleared but came back after turning the car off and on again. Kinda at a loss for where to go next so any suggestions would be greatly appreciated.


r/cruze • • 3d ago

P1101 Question

Post image
1 Upvotes

I posted about a month or two ago about CEL coming on for my Chevy Cruze 2017 LT with 108k miles and getting a P0299 and P1101 code together, I finally took it to a mechanic last week and it was the wastegate, they adjusted that correctly and I have not seen the P0299 code again yet.. Flash forward to this week and the check engine light came on on my way home, I turned the car off to go get a reader so I could see the code and when I came back and turned the car back on the check engine light was off again, I still read the code and was getting P1101 MAF as seen in the pic attached. I contacted the mechanic and he seems puzzled now saying the MAF sensor and everything else they tested was “all reading within spec when we tested it and it looked clean.” I brought up that maybe it could be PCV related and he doesn’t think so replying with, “A leaking PCV valve throws another code. it would be a p0171 code. The charge pipe if it was leaking/had a hole in it, it would be the same p0171 or another under boost code.” I am not sure what to think or do now because he did check the whole list of things, turbo, throttle body, MAF sensor, smoke test, fluids, when diagnosing the codes the first time and found nothing.. Could this be an electrical issue and nothing is wrong at all?? I’m at my wits end with this car.


r/cruze • • 3d ago

Oil Change

3 Upvotes

My partner owns a 2016 LT 1.4L Turbo. The last time we went for an oil change was when the car alerted us to get one using the Oil Life %
The mechanic kinda told us off for going way over the limit and that we should have changed it sooner.
Current sticker states we should get it changed at 143k kms but we’re currently at ~145k kms. The Oil Life % is still 20%.
My question is: what to follow, the sticker or Oil Life %?


r/cruze • • 3d ago

Coolant leak

Post image
2 Upvotes

I replaced the upper heater hose and it’s leaking out of this end now. Is there something I did wrong or something else is wrong?


r/cruze • • 3d ago

Help

Post image
1 Upvotes

I lost that red clip for the evap purge valve does anyone know where I can find another one or what it’s called? Please and thank you in advance


r/cruze • • 3d ago

Gen1 - General P0420

0 Upvotes

Trying to get this engine code away to fully inspect the car (emissions state here in NJ). Is the cat converter an expensive replace? I just want to make sure the car can thrive+least be good to go+I will have to change the oil, it’s throwing a change oil+oil life is at zero based on the code scanner from autozone today.

Also what could be the other problems+im still in the midst of ordering the Cruze kit as well, I’m leaning towards waiting the two months for version 3.5 but I dunno, I do want the car to be good to go to actually drive+got a farther job now.


r/cruze • • 3d ago

A/C problems?

2 Upvotes

So to start off I have been fighting my A/C most of the summer trying to get it to work.

I hooked up my gadges and made sure they were reading good.

Replaced the pressure sensor.

Drained the system and replaced the compressor, then recharged it.

I haven't flushed the lines and cooler yet.

The thing that I don't understand is that the cooling fan runs almost non stop regardless of the car temp or outside temp or if the A/C button is on.

The only time I can get the compressor to run is if I jump the relay.

But then it's still not cold.

I also replaced the button on the dash, checked all the fuses and the relays.

What am I missing? Could it be another bad compressor?


r/cruze • • 4d ago

2018 chevy cruze 1.4L

2 Upvotes

Hearing a whistle as my engine is in idle and its gets more distinct when i press on the gas. No cracks on intake hose and is fastened. Have a p1101 code a while back, cleaned the throttle body, also replaced the MAF sensor. Need to be pointed in the right direction. Anything helps thank you fellas


r/cruze • • 4d ago

Please help I'm at a complete loss

1 Upvotes

I have a 2014 1.4l and out of no where ive lost break lights i still have my 3rd one put left and right side do nothing at all...they are just lit up...ive tried everything i can think of new brake position switch...new bulbs...fuses...idk what else there is to do can anyone please save me from losing my mind here


r/cruze • • 4d ago

Cruzekits Update

56 Upvotes

Andrei here with CruzeKits.com. I have a few updates to provide.

First, my v3.5 PCV fix kit version update will be shipping in about two months. This upgrade solves the primary pain point people have provided me feedback of; installing the manifold plug. The new kit will feature a newly designed quick tool that eliminates this problem. It took three months of R&D and 12 product revisions to design this, but it’s finally ready and currently in production.

Second, please note that this year, I released new PCV hoses. These have my own TitanSynthetics logo and are manufactured to my specifications for this application. These use a KFM inner liner and aramid fiber double crossweave reinforcement. The added strength has held 18in-hg of vacuum clear to 250F. The downside is that the new hose requires a heat gun and grease to install. The video showing how to do this is on the cruzekits site, and it’s really quite easy when done correctly. I was able to demonstrate this to someone just 8 weeks after I had broken 8 ribs, my collar bone, and my shoulder blade in 3 pieces, so it didn’t take much strength when done correctly. I’ll have the hose for sale separately soon if anyone wants to upgrade theirs.

Lastly, I wanted to address a claim that we don’t deliver orders in a timely fashion. I ship out products within 2 business days of the order being placed and all expedited orders ship within 24 hours; any delays beyond that are completely out of my control. I’ve had USPS Indianapolis DC lose a valve cover box for two weeks before and several priority mail packages get delayed for over a week. The only delivery timelines I guarantee are for UPS next business day air. As we get farther into the holiday season, more delays are inevitable as carriers are overwhelmed with package deliveries. I’m doing the best I can here but I have no control over what USPS or UPS does with the package once it leaves my office.

Thank you for your time and understanding.