r/bookbinding • • Oct 01 '25 Heartwarming This

Gauffering

Thumbnail
gallery
3.7k Upvotes

These are the final results of my first gauffered book.

I started researching gauffering in February, and was a bit surprised by how little information there was about the process online. A friend sent me pictures of a few pages from An Introduction to Gold Finishing by John Mitchell, which were interesting to read. Unfortunately, working with actual gold leaf is outside of my budget and skillset, so I had to look for other options.

In April my brass finishing tool from Talas arrived, and I decided to experiment on some old textbooks. After many failures, I found a method that worked for me: I sanded my textblock to 2k grit, painted the edges with acrylic ink, waxed them with Renaissance Wax, and polished them with an agate burnisher. I then taped down a piece of foil, and taped a cardstock grid on top of it to keep my lines straight. I don't have a finishing stove, so I heated my tool on my gas stove (hot plates did not work for me).

This worked nicely for an amateur bind, but I would love to hear from more experienced people on this subreddit. Have you tried gauffering before? Is there anything you would have done differently? I'd love to hear any advice anyone may have!


r/bookbinding • • Apr 13 '26 Heartwarming Bravo

Completed Project Exposed spine binding - wisteria stitch

Thumbnail
gallery
3.3k Upvotes

These books are inspired by wisteria flowers. When I look at a wisteria, I noticed that flowers that have bloomed tend to have a lighter purple than the buds. I used the beads as a representation of those buds.

Each book took an average of 6-7 hours to make with the spine being the most tedious part. The first prototype (left thinner spine on image 1) has little leaves under the cords. I decided to omit it for a cleaner look when I sewed it again. I quite like both versions, the prototype being even more time consuming to sew because of the tiny leaves.

I’m actually doing an EU giveaway for the book (image 1-7) on my Instagram (link in profile) that will last until 18 April, so there’s still time to enter. If you have an IG account and live in the European Union, United Kingdom, Iceland, Liechtenstein, Norway, or Switzerland, you can enter.

——

Materials: Olive green Sevenberry heathered solids Japanese cotton fabric, embroidered cotton fabric gold and purple chiyogami, abstract green chiyogami, fabric and book cloth scraps, koho seed beads, jute cords

Thread: Lilac, purple, hunter green linen

Paper size: A6

Signatures: 12

Pages: 192


r/bookbinding • • May 13 '26 Heartwarming Bravo

Completed Project Purple, blue, and pink wisteria on exposed spines

Thumbnail
gallery
2.6k Upvotes

Last month, I made two additional wisteria colors in pink and blue. These are square sketchbooks with hot-pressed 300 gsm Fabriano Artistico watercolor paper.

Materials: Various cotton fabrics, various chiyogami papers (Kyukyodo), fabric and book cloth scraps, koho seed beads, miyuki seed beads, hemp cords
Thread: Lilac, purple, hunter green, pale blue, blue, russet, pale pink linen
Paper size: 15.2x15 cm
Signatures: 12
Pages: 48
Usage: Sketching, watercolor


r/bookbinding • • Mar 02 '26 Heartwarming

Completed Project Botanical Spines with William Morris Strawberry Thief Fabric

Thumbnail
gallery
2.3k Upvotes

Hi Reddit, I’ve been a long time lurker. I saw so many inspiring posts from here, and it made me want to contribute to the community. I’m just a hobbyist that’s extremely passionate about exposed spine bindings.

This is the second platform I decided to post on outside of Instagram. I hope to learn more from everyone here and continue to push the limits of exposed spines!


r/bookbinding • • Feb 01 '26

Completed Project I typeset and bound my Sister's dissertation as a graduation gift!

Thumbnail
gallery
2.2k Upvotes

This is something I put together last Summer as a graduation gift for my Sister. As far as actual 'bookbinding' goes, it was very barebones and simple - just a simple kettle stitch with a bit of glue on the spine of the text block, before sandwiching it between two boards and wrapping it in blue/grey/white cardstock. All this to say - I have no idea how well this will hold up to the annals of time or dirty fingers, but it looks pretty!

The cover design was printed on grey card and glued to the boards. I then printed the same design on white card, cut and removed the windows of text from the grey cover, and replaced them with the windows from the white sheet. The alignment on this wasn't as seamless as I would have liked, but it's close enough that a passing glance wouldn't be able to notice.

For the glittery GAY, I carved out a shallow well in the greyboard in the shape of the letters. This was so that the glitter would be slightly recessed and I wouldn't have to worry about it coming off if it came into contact with other surfaces. The G was a bit finicky due to the curves, but I'm delighted with how well it worked.

Sister was very happy with it when I gifted it to her. Big success!


r/bookbinding • • Jul 14 '25 I’ll Drink to That

Completed Project Had this funny idea to rebind Charlie and the Chocolate Factory to look like 1971 Movie Wonka bar!

Thumbnail
gallery
2.1k Upvotes

That idea became reality when I stumbled upon a copy during a Little Free Library run. I really love how this one came out, minimal but still gets the point across! The gold end pages are my favorite, ready for unwrapping and digging into the story!


r/bookbinding • • Apr 22 '25

Some embroidered rebinds I’ve done

Thumbnail
gallery
2.1k Upvotes

r/bookbinding • • 27d ago Heartwarming Mindblown

How-To I made this handmade leather journal with a stained glass rose design

Thumbnail
gallery
2.1k Upvotes

Hi everyone! I wanted to share this leather journal I recently finished. The cover features a stained glass-style rose design with hand-painted details. Swipe to see the back and the details on the embossed spine. I’m really proud of how the colors and textures turned out. Let me know what you think


r/bookbinding • • Aug 03 '25

Completed Project My first marbled fore edges! Hand drawn and foiled chapter headers. Sewn headbands. Cover art and typeset by me.

Thumbnail
gallery
1.9k Upvotes

There are a lot of errors that the camera angles hide. I was really frustrated. And I wish i had got silk thread for the end bands to really make them pop. But these are all lessons for next time!

Check it out in Reel form on my Instagram @hyacinth_bindery


r/bookbinding • • Mar 20 '25

Inspiration Commercial bookbinder here! Photos of a working bindery, Victorian tools

Thumbnail
gallery
1.7k Upvotes

Here is a link to the website of my buisness which will link you to our instagram.

https://www.bookbindingetc.com/

Both me and my boss in the small buisness struggle to take step-by-step photos when super swamped

If you live in New Zealand and are in Wellington, come by for a nosey


r/bookbinding • • Jul 29 '26

Completed Project Lectern Binding first attempt!

Thumbnail
gallery
1.7k Upvotes

Been planning this project for over a year (originally wasn't planning to do a lectern binding), but accidentally deleted my typesetting of the text right before printing last October so it was put on hold. I came across the amazing guide by @amessinpictures, so I decided to restart the project with that in mind, so here is my lectern binding of China Mountain Zhang by Maureen F. McHugh, as well as the short story set in the same world called Protection. It was a long rewarding process, and I’d be happy to answer any questions about it!


r/bookbinding • • Jul 29 '26 Heartwarming

My immortal

Thumbnail
gallery
1.6k Upvotes

Apparently, I couldn’t avoid My Immortal. Wife commission for one of her friends, she requested a more subdued typeset than the community one (I printed the community one and might bind it anyway because it is stunning) so I threw a quick one together.

I did a half bind with some home made marbled paper and black book cloth that I think came from amazon….0 out of 10, do not recommend, its terrible stuff, frays like nobody's business and I will be throwing the rest of it away. Endpapers are some home made paste paper, made it look as Emo as I could without having to make a new batch of either marbled paper or paste paper. First time doing edge decoration, I was going for “blood drops“ to match the emo vibe and it sort of worked, I used regular acrylic but I feel like I should have diluted it with water so it didn’t go on so thick but overall not too upset about it, next time ill dab the paint on after rounding, not before.

Slipcase was made of the aforementioned cursed bookcloth and some printed marbled paper that I think came from lineco.


r/bookbinding • • Oct 16 '24 Heartwarming

Completed Project Bound Avatar the Last Airbender scripts

Thumbnail
gallery
1.6k Upvotes

The transcripts of the TV show are available online, so I bound them as a present!


r/bookbinding • • Sep 06 '24 Heartwarming

Completed Project My 2nd bind

Thumbnail
gallery
1.5k Upvotes

I started this project in May or June 2024, but it feels like I've been working on this for an entire year. This is my second attempt at combining embroidery & bookbinding, so most of the time I spent on this consisted of learning how to embroider & book bind. I'm convinced that there are probably much simpler methods out there that I just didn't have access to & being so new to this hobby, I was winging it on a lot of stuff.  
For this bind, I used the following:

  • Short grain 11x8.5" paper from Church Paper

  • Typeset: Mrs. Yoflam’s Books

  • Fore-edge folding technique for the signatures (no guillotine)

  • French link for sewing the signatures

  • bradel method for the book casing 

  • 100% cotton canvas for the bookcloth

  • Husqvarna In-R-Form Plus Batting

    • To eliminate the bumps from the thread knots on the cloth, I cut the batting to size (for the front cover, back cover, & spine), left gaps between the hinges in an effort to make those more defined, & used heat-n-bond, then regular tissue paper. 

    • I did not love this method very much since the heat-n-bond was under tension over the hinges while ironing. So ultimately, the crispness of the hinges is not very great. I really hope I can come up with a better solution for this in the future. 

    • Side note: this entire process was incredibly freaking stressful. I was sweating the entire time. 

  • Embroidery design inspired completely by graphic artist, Olivia Jensen. 

    • I was looking up completed binds for inspiration when I came across her website. I thought “wow, this would be incredible to embroider.” Her instagram handle is olivvyjensen.

  • Super Solvy Water-Soluble Stabilizer - I used this for the front cover & traced over the design on my ipad in Procreate. This was time consuming as hell because the design was so busy & the stabilizer easily shifted (I taped down the sides of the stabilizer to the ipad in an attempt to keep it in position). 

  • Sticky Fabri-Solvy: Self Adhesive, Fabric-Like, Water Soluble Stabilizer - I used this for the spine & back cover. This was MUCH easier to work with & way more flexible in terms of just sticking onto whatever part of the fabric; however, I found that the adhesive was problematic when threading the roses (more complicated knot). 

  • 12-inch embroidery ring  Major Mistakes: 

  • Along with the water-soluble stabilizers I was using for the design, I was also using a white ink heat erasable pen to mark certain areas (like the width of the spine, covers, & hinges). This was great because you can just iron the fabric & the ink disappears. Towards the end, I was a little tipsy & I made the horrifying mistake of using a regular white pen instead of the heat erasible pen…. This wouldn't have been such a huge deal if I didn't realize this until a few days later when I was ironing the fabric to get it ready to glue to the bookboard. By ironing over the ink excessively (because I still thought it was heat-activated ink at this point), I completely set the ink in the fabric. You can imagine I was quite devastated. I tried to scrub it out, I used stain remover from the craft store, & I tried to find fabric markers to match the navy blue of the fabric, but there was nothing to be done. So now the white ink will remain forever… sigh

  • Busy Design - I wish I wouldn't have been so ambitious with this. Although lovely, this busy design made it super complicated to line up on the book board no matter how much effort I put into staying within the border. With the fabric being stretched tight while in the ring, it made the design (specifically the border placement) a few millimeters off (see bottom right corner). It came out great, but I don’t think I will ever do a design this busy again - too much effort lol!

Resources: Mrs Yoflam’s Books (Patreon)  Beautifully Bound by Sophie (Patreon) Ladybobbitt (Instagram) Abound Bindery (YouTube) Foolproof Flower Embroidery by Jennifer Clouston


r/bookbinding • • Aug 25 '24

Completed Project Finished binding up my GF's first draft of her book

Thumbnail
gallery
1.5k Upvotes

Here's the finished piece, it went ok. In the future if my gf makes any books with the first draft longer than 1k pages I will heavily suggest that it is split into two smaller books. It was printed on A4 sheets then oversewn to make the text block. I didn't go all out on the design since It is a first draft and I figured some plain buckram would be more hard wearing and practical for it's use in editing. It is difficult to read because of its size and getting the squares right was a challenge. I really should have recut the boards to match the shape of the book. However she is happy with it's girth and it does make a very satisfying thump when you put it down on tables or close the covers. I left the label blank on the front cover so she could write the title by hand. When she has finished it I will make a clamshell box with a small 3-4 mm ledge to support the book block.


r/bookbinding • • Jan 19 '26

Completed Project Rebind of The Diary of Anne Frank

Thumbnail
gallery
1.5k Upvotes

The idea behind this cover was to emulate the Secret Annex where the Frank family was hidden. I chose a dark brown leather to create a sober, restrained look, and used cardstock to build relief elements representing a bookshelf and book spines.

The cover opens in the middle, as I wanted the book to resemble a box rather than a traditional binding. It closes with magnets hidden behind removable book spines, which can be repositioned inside the book once it is opened. I initially wanted the closure to be more discreet, but smaller magnets were not strong enough to keep it closed securely.

The fore-edge was painted in a color close to the leather, reinforcing the idea of a box that reveals nothing from the outside. Once the book is opened, the endpapers contrast sharply with a bright color, representing Anne’s inner world, her imagination and hope.

Everything was cut by hand. The interior was designed to represent the inside of the Secret Annex from Anne’s perspective:

On the first floor, Anne writes in her diary while Dussel comes down the stairs.

On the second floor, the family gathers around the radio while the Van Daan couple has a heated argument.

In the attic, Peter cuddles the cat as Anne looks at the stars and the chestnut tree, dreaming awake.

The final endpaper recreates her famous wall filled with photos of celebrities.

This was the hardest commission I have ever done, and also the most ambitious. I would love to know what others think about it.


r/bookbinding • • Jun 20 '25 This

Illustrated and bound a campaign book for my D&D group

Thumbnail
gallery
1.4k Upvotes

I kind of become really obsessed with bookbinding in the last few months. Naturally, since it lets me bring all my other hobbies - ttrpgs, reading, drawing - together!
This book has been months in the making, and I can finally share! I‘m very *normal* about playing Dungeons & Dragons with my friends, so I created this book for our completed campaign to collect all of our session summaries, the character sheets, notes on npcs and important items and all the letters and notes found during the game. I also put in all the art that my player and I made during the campaign (she drew so much - I‘m truly blessed). Some of the art I made just for the book (title page, dust jacket, character item illustrations, b/w chapter illustrations).

The hardcover depicts two-legged pug Sir Mopsington who got possessed by Lathander to speak to our cleric. Truly an icon. The dust jacket has some nods to the campaign with the front showing the player characters and the back showing the villains. I decided not to trim the textblock because I don’t have a reliable guillotine but I think the deckled edges add to the handmade charm.

Overall, I spent about 150 hours making these books and bound 6 copies - one for me and one for each of my players. Typesetting took me ages and the dust jacket was also an undertaking - especially getting it printed.

All art shown is drawn by me, except for Sir Mopsington‘s design who was drawn by a player.


r/bookbinding • • Mar 14 '26

Made my own folding tool from paint sticks

Thumbnail
gallery
1.4k Upvotes

I’m new to book binding , as in I haven’t done a project yet. But I’m trying to spend as few dollars as I can because I don’t know yet if I’ll like it enough to continue as a hobby long term. So I made this bone folding tool out of two paint sticks that I wood glued together and then cut into shape with a hand saw and sanded down. I stained and then sealed with polycyclic gloss. Just wanted to share as I’m pretty proud of it!


r/bookbinding • • Sep 17 '26 Bravo

Completed Project An Experimental Bind : Sashiko Embroidery as a Binding Stitch

Thumbnail
gallery
1.4k Upvotes

This is me, making things, once again.

This is a travel journal I made for a friend of mine while traveling myself.

I decided, against my better judgement, to make up a new (for bookbinding) kind of stitch to bind the book, or at least I've never seen it before.

It's experimental because the signatures are bound directly to the spine of the cover using a sashiko embroidery stitch, modified to work with the limits of the signatures.

It's definitely not perfect (and I burnt some threads so I'm mad at myself) but it looks fairly decent to me. Hope you'll like it, too.

If you have any questions, feel free to ask.


r/bookbinding • • Oct 23 '25

Is this a common bookbinding struggle? Working on my first project.

Post image
1.4k Upvotes

r/bookbinding • • Sep 06 '26

Inspiration The slow craft of carefully rebinding an old book

1.4k Upvotes

r/bookbinding • • Jul 15 '26

Completed Project Frankenstein!

Thumbnail
gallery
1.3k Upvotes

So, I have a bit of an obsession with Frankenstein. And I realized that, despite this major Frankenstein obsession, for some reason, I didn't actually own a copy of the original book. So, I went and fixed that and made this! It's coptic-bound, with a little extra decorative stitching to make it look like Frankenstein stitches. It was a bit tricky to make sure the embroidery on the bookcloth lined up with the stitching that attaches the cover and make it all blend together, but it was sooooo worth it! I'm literally so ecstatic with how this turned out! Especially since it's only my 3rd project haha. It was my first time making something where the pages needed to be in order, so that was a bit challenging to figure out how to print. But now I have the coolest looking copy of Frankenstein ever! :)


r/bookbinding • • Jul 25 '25

Inspiration Discworld Wheel

1.3k Upvotes

r/bookbinding • • Mar 23 '25

Completed Project My best work yet

Thumbnail
gallery
1.3k Upvotes

I'm a newbie to the hobby. This is my 8th rebind and my best work yet. First attempt at guilded edges and a faux stained glass (resin) insert The back are the moon runes from Thror's map and the cover material is a faux suede. Loving this hobby and thankful for all the inspiration I get from this community. Glamour shots and some process pics for your enjoyment. Comments and criticism welcome :)

(100 fake internet points to anyone who can find the mistake I am not risking fixing)


r/bookbinding • • Apr 05 '25 Take My Energy Popcorn

My latest project and the first rebind of a history book.

Thumbnail
gallery
1.3k Upvotes

This is the result of my most recent commission, a gift for my client’s husband, who’s a history enthusiast.

The cover draws inspiration from Roman funerary steles, which were tributes to the dead, often framed with ornate designs mimicking Roman architecture. For the inscribed stone within, I turned to Roman epigraphs, which recorded significant messages like laws or decrees and felt more fitting for the inscription’s meaning. With this in mind, I crafted a Latin text that translates:

"Time flees, memory endures, deeds are eternalized through writing, and truth withstands the darkness of oblivion and ignorance."

To me, this ties perfectly into the context of a history book. To emphasize this concept, I designed the relief as if it were a stone cracked by the passage of time, with part of the message lost—leaving it to be deciphered and interpreted. I chose ivory-toned leather to evoke the look of marble.

The fore-edge painting was inspired by the floor of the Curia Julia, a key political building in Rome. It was mostly done in watercolor. I finished it off with a hand-sewn headband using the same color palette.

The endpaper features an illustration in graphite pencil, India ink, and a touch of watercolor. My inspiration was the martial spirit of the Roman people, present since the city’s founding (according to legend) and heightened during the empire’s expansion.

The illustration includes a bust representing the god of war (Mars), alongside a sword, a spear, and a shield. Pomegranates symbolize the wealth and prosperity gained through those battles.

I’d like to take a moment to thank this community for its kindness. In my last post, I received great suggestions and insights from people working in this field.

I’ll also ask one more question: I currently work only with one-of-a-kind, custom-made editions, but this approach isn’t sustainable for me as a business. I’d like to experiment with more elaborate designs, though that would drive the price up significantly. I’m considering producing limited runs of 5 copies each to make them more affordable, but I’m worried it might lessen their appeal if they’re no longer truly unique. Do you think this would take away from the book’s charm?