r/SolarDIY • • 14m ago

Battery disconnect and fuses/breakers?

1 Upvotes

Hey all! Looking for some advice for my parents.

They're setting up a pretty ambitious DIY program - 32 440W panels, two 10 kW inverters, and six 100 AH lithium ion batteries. The kit they purchased as an alleged "comprehensive" package was anything but - the included wiring and breakers are all IEC listed and this will be grid-tied, so it isn't up to snuff for NEC 2023.

The issue I'm struggling with is fuses and disconnect switches or breakers for the battery bank. The included IEC breaker is 300 A @ 500VDC. I'm struggling to find UL listed options that aren't going to run $2500-3500 for both inverters, plus they may add a third later. At this rate, these three switches would be 20% the cost of the whole project.

Does anyone have any recommendations for products or alternate, code-compliant ways of pulling this off?


r/SolarDIY • • 2h ago

Custom Solar Ground Mount on Granite Boulder

Thumbnail
gallery
116 Upvotes

3x 430W REC panels, 1x NEP BDM 1200-LV 120V plug-in microinverter. I just finished this yesterday, I do not have any production numbers (believe me, I'm more disappointed than any of you 😅)

Title says it all. My parents house has this weird ledge of granite that's a super awkward shape on a steep hill. It's always been in the way. No grass. Could never plant anything on it. Only moss grows. Even just decorating it has always been a colossal PITA. So I finally decided you know what, I'm gonna build a ground mount on it. It gets sun ALLL day during the summer, and my parents have these big pumps for their pond. Why not get some solar 😎

Bought a cheap rotary hammer and went to town. I demo'd the granite until I hit solid rock, drilled holes and installed 1/2" threaded rods as anchors w/ Sika Anchorfix 2, two rods per footer, ~6" deep minimum. Some of the granite was REALLY badly weathered so I had to demo down over a foot just to get solid stone. I hit it eventually. I also hammered into and flattened the areas as best as I could and lined them all up.

Then, I installed very stiff rubber pads so the footers would have something to help keep them level, and wouldn't sit in any standing water. I also carved channels to drive any water away.

I started with my 3 front footers and and cut strut so the heights would be all exactly the same, true horizontal. Then, I measured and cut all the strut for the rear footers, to connect to the front ones at a 35 degree angle. I had calculated 36-39 degrees was optimal for the latitude (New England) and the azimuth (about 220 degrees), but 35 is what I could achieve consistently with the amount of strut I had. This was really tough for the angled footers, since the connection was free to move around. All the support pairs were 35±0.4 degrees. Considering how absurdly uneven the rock was to start, I'll take it.

Once I had all the front-rear pairings done, the hard work was over. Laid strut across for the full length of the panels, leveled with a laser, and then then panels followed soon after. Attached the inverter to the back, and wired it all up.

It came out SUPER clean, I'm very happy with it. My wife encouraged me to share it with you nerds.

Also, I powered the my little jobsite with my car 😁


r/SolarDIY • • 3h ago

How does this setup look?

Post image
9 Upvotes

Building out a 48V backup battery solution. Victron Multiplus II 3000VA paired with smart shunt, lynx bus bar, two 150/45 MPPT’s for solar input. Plan to build out subpanel for critical loads that cover network equipment, fridge, freezer, lights, outlets etc. no 240. Grid power added in for backup but plan for battery and solar (which I’ll add in a few months) as my primary source for those circuits. For now it’s just an outage backup solution h til the solar is added.


r/SolarDIY • • 4h ago

Ideas for extra panels

6 Upvotes

I just bought a pallet of 36 440w panels, I have all but 5 installed to charge my batteries, and to help offput power to my solar mini split.

So I still have 5 left as well as 10 of my old 410w panels.

What are some other devices that could be run off of them that could be handy just in case?

I've already got 30kw hours of batteries, along with 2 apex 300 and 2 batteries for those as well..

I'd love to hear what else could be useful and can be powered by larger panels!


r/SolarDIY • • 14h ago

I tried comparing two spots for solar panels with the lux meter I use for my plants

3 Upvotes

My first choice for the panels was the stretch of railing by the balcony door. It was easy to reach. The other spot was farther along and had a clearer view across the courtyard. I wanted to see if it got enough extra sun to be worth the hassle. We were planning to use a Jackery SolarVault 3 Pro to save some of the daytime solar for the evening. I still had to mark the panel position on the sketch for the installer.

That afternoon I used my houseplant lux meter to take readings at both spots as the shadows moved. I took photos too. Back inside, I tried an online conversion from lux to watts per square metre, hoping the numbers would give me a way to compare the two.

Before putting the numbers in our notes, I checked how the conversion worked. Lux is weighted for human vision, and the conversion depends on the light spectrum. I couldn't tell if the same factor made sense for my readings in sun and shade, so I left the converted numbers out. When my partner and I looked at the quote, we marked the afternoon shadows on our sketch using the photos. We still wanted to see how much shade each spot got in the morning before picking one.


r/SolarDIY • • 16h ago

Cleaning up extremely dirty solars

Thumbnail
gallery
244 Upvotes

Hi I've got for free these solar panels, they have been used near an highway so they are completely dirty

I tried ammonia, wheel hub cleaner, toilet cleaner , paint solvent , only thing works you see it in the photo and it makes harmful fumes and my wrist is screwed after doing half a panel, I have 60 to clean up :D

After cleaning they work pretty decent for their age so it is worth it , I mean free is free Any idea / suggestion?


r/SolarDIY • • 19h ago

[US] [E10] [CA] Answers to questions I was not able to get here or elsewhere..

5 Upvotes

After a few days wait to get the right information Anker Sales team responded with this info. I am in the process of ordering a single 30KwH stack this morning.

Sorry for the delay in getting back to you! Here are the concise answers to your questions regarding the Anker SOLIX E10 30kWh single-stack system with the Power Dock:

1. Can the power dock be used without transferring critical loads wiring to it and still have Auto Failover?
A: Yes. An electrician can wire the Power Dock between your utility meter and your existing main panel (Whole-Home Backup configuration). Your entire panel gets automatic failover (<20ms) without rewiring individual circuits, though app-based smart load shedding only works on circuits wired directly into the Power Dock.

2. Can it power my whole home (max 6kw) 24x7 like the SIB can and not export power to the grid in that PD configuration? There is No payback from my POC so I never want to export but I want grid tied as a backup.
A: Yes. You can run your home off the E10 (up to 7.68kW continuous) in Self-Consumption or Time-of-Use mode with the grid as backup. The system is certified for zero-export (UL 3141) and uses an open-transition transfer switch to prevent backfeeding the grid.

3. Will it import power from the grid as needed, Example: if I attempt to exceed the 7.6kw of the Inverter?
A: Yes. While on-grid, if your home draws more than the inverter’s 7.68kW continuous limit (or 10kW turbo peak), the Power Dock automatically supplements or bypasses power from the grid.

4. Can I charge the batteries directly from that Grid if I need that? Your document lists everything, but not charging directly which seemed odd to me.
A: Yes. The Power Dock supports direct grid charging at up to 9.6kW, which you can schedule via Time-of-Use (TOU) mode or trigger automatically ahead of severe weather using Storm Guard.

5. During Outage will it keep my existing Balcony Solar Micro Inverters running?
A: Only if hardwired (240V). Standard 120V plug-in balcony microinverters will shut down during an outage for safety. Hardwired 240V AC-coupled microinverters will stay running if landed on the Power Dock’s dedicated AC-PV terminals (Circuits 7 & 8).

5.1 If so, where do I find a wiring diagram to allow that to work?
A: Check the AC Solar / Retrofit section (Circuits 7 & 8) in the Anker SOLIX Power Dock (AX170) Installer Guide or the E10 Third-Party Solar Compatibility Guide.

6. Does it come with the paperwork to show the building inspectors its UL approved and California approved?
A: The box includes a quick start/safety guide, while the full PDF certificates (UL 9540/9540A, UL 1741 PCS, UL 3141, CPUC Rule 21, and CEC listings) and Non-Export Statement are available on the Anker SOLIX Support Download Center.

7. Can I add an extra wall bracket or does it interfere with stacking the lower batteries? I live in an Earthquake zone.
A: Yes. For a 5-battery (30kWh) stack, Anker actually recommends adding a second wall bracket on top of the 3rd battery in addition to the top bracket. It fits cleanly between modules without interfering with stacking and must be anchored into studs or masonry per local seismic codes.

Again, apologies for the wait. Let me know if you need anything else.

Warm regards,

xxxxx
TicketANKER-TNV680020xxxxx
The Anker SOLIX Sales Team


r/SolarDIY • • 19h ago

Grid Tied - Enphase - Inverter / Battery Alternative Setup

2 Upvotes

My goal is that when power goes out that my solar panels continue to provide power to the home and a battery to handle dips / no sun. I'm also trying to save on battery costs by topping off the battery using my EV's V2L. I am fully aware that is a janky workaround but hear me out. Using the EG4 Chargeverter, I can attach the connections to the bus and top off the battery at around 1500w factoring in some loss. My nighttime load (which is when I'd probably use this) is averaging around 600w notwithstanding surges for fridges and furnace blower etc, which the battery could handle for those pulls. But on average, the rate coming into the battery would be higher than its output and could either maintain or even charge the battery. And with a 77kWh battery, it could charge for quite a while, even if not very powerful.

Equipment I am looking at:

- EG4 18kPV

- EG4 16kWh indoor walll mounted battery

- EG4 Chargeverter to top off the battery from the EV V2L

I know this is a DIY forum, but my electrical skills and knowledge are weak and am hoping (and expecting) some pretty frank feedback.

I have an installer I am working with who is happy to go the customer provided equipment contractor installed route and they say my setup would work but they wanted to install a transfer switch for my EVSE since if power went out while it was in use at its typical 40A charge rate, the inverter would trip immediately.

I also have 1:1 net metering with my utility and would rather operate the 18kPV in a Battery Backup Mode vs Self Consumption profile since I don't care where the energy is coming from, just that the battery stays in a topped off state.

Not shocking but this really comes down to my budget, we have around $10k we're wanting to throw at the install and batteries and obviously most people in here would say get more batteries! And I'd love to, and to go more robust, but I am limited.

And, because this is grid tied, everything needs to be on the up and up for a fully UL 9540 certified ESS system.

So this is an AC coupled solution and the reason I'm trying this route vs the quote I got from enphase is firstly, their quote was absurd, but also their solution uses a very throttled version of my full solar array, and I couldnt top off the battery with my V2L.

Fire back thoughts! Thank you in advance for any help!


r/SolarDIY • • 1d ago

Rerouting PV wire electrical question

Post image
0 Upvotes

I need to relocate solar wire while it’s still attached to my solar panels (see photo). I plan to do this during the morning while solar generation will be strong. The solar cable that I will be holding and pulling wire will have an mc4 connector attached to the wire, so no bare wire should be exposed.

Is the risk of being electrocuted extremely small, or am I at high risk of being electrocuted?

Besides blankets over the solar panels, is there another method such as putting electrical tape covering the ends of the mc4 connector to be safe? I don’t plan to blanket over solar panels if the risk of electrical shock is small or have other methods like electrical tape. Wondering what are my options to relocate wire safely.


r/SolarDIY • • 1d ago

Absolute beginner kits and walkthrus

1 Upvotes

Thoughts on this all-in-one?

https://signaturesolar.com/complete-hybrid-solar-kit-eg4-powerpro-ess-12-kw-ac-output-up-to-45-kwh-battery-backup-kit-e0007/

Looking to diy a setup but unsure where to start other than an all-in-one

Im thinking if Inwas able to diy build 2 bedrooms / 2 bathrooms in my house, I can do solar too.

Appreciate your insight


r/SolarDIY • • 1d ago

Is an hybrid inverter/battery outdoor ideal?

3 Upvotes

I live in Mexicali, Baja California, one of the hottest places on Earth. The year ago we reached the maximum temperature of 52 Celsius. The temperature range of the EG4 Outdoor Wallmount 48V 14.34kWh is 0 - 50 Celsius. Is it really reasonable to have an outdoor rated equipment at our scorching temperatures?


r/SolarDIY • • 1d ago

Beginner Friendly

Thumbnail
gallery
6 Upvotes

I'm trying to think of starting my Solar journey

Which one would be a good starter Controller between these two? LiTime is $140 while Eco worthy is $152.

I currently have 2 410watts solar panel with VOC of 50 and 9A. I'm planning to get at least 4 more same panels over the weekend. I currently have an ecoflow delta 3 ultra plus and a seperate 12v 300h lifepo4 battery. My plan is future expandibility. TIA


r/SolarDIY • • 1d ago

Beta testers wanted: Neighbor Solar, Android app for SunPower panel-level monitoring (PVS5/PVS6)

0 Upvotes

I'm looking for beta testers to run the closed test Google requires before I can publish it on the Play Store. Google needs 12 testers opted in for 14 days.You need:Android 7.0 or newerA SunPower PVS5 or PVS6To stay opted in for 14 daysIt is a paid app ($5.99/year) but the 15-day free trial covers the whole test, so you pay nothing.How to join:Open the beta group link: https://groups.google.com/g/neighbor-solar-testers — sign into your Google account if asked, then tap Join group.Then opt in on Play here: https://play.google.com/apps/testing/com.sushi.neighbor_solarNote: after joining the group, it can take a few minutes before Play recognizes you. If the Play link says unavailable right after you join, wait a bit and try again.If you don't have a PVS you can still join the group and count toward the 12 testers Google needs, but the app will stop at the gateway scan since there's nothing to connect to.Happy to answer questions in the comments.


r/SolarDIY • • 1d ago

Why is my soc showing 100% all the time? Battery is ESS fron nkon 16kw, bms is in ve,can both sides

Post image
2 Upvotes

as title says. I have no idea why its showing 100% all the time


r/SolarDIY • • 1d ago

Aeternasol Solar panels question

2 Upvotes

Hi everyone,
I’m looking into Aeternasol panels for my van setup.
I will connect 5 in series (3 200W 2 100W) and I wanted to know if anyone here has some experience with them.
I’m also debating if I should go for 5 in series because their voc is around 26 and I will reach high voltage numbers.
My battery bank will be 24V 314ah


r/SolarDIY • • 1d ago

Advice repairable lifepo4 48V battery (Europe)

1 Upvotes

Hi 👋

First of all I live in Europe.

I have been looking forever for a Lifepo4 battery 48V where the components could be changed if they fail.

So far the only 2 options I have found are :

- Seplos Mason 280 3.0 (Add 16 EVE cells) that I can easily fix but then I have very little warranty (1 year) and it would cost me around 2200€ for +-14KWh

- NKON ESS Pro 16.1 KWh, all the components are repairable and it comes with a 6 years warranty at +-2200€

But those batteries are both too big for my use. I would like something more around 10KWh.

I would like something smaller and cheaper. Am I looking for a unicorn or someone as a lead for something ?

NB : Part of the question is that I don't want to go any higher than 2000-3000W of solar panels.

NB2 : I thought about 12V system since I'm living in an off-grid setup where my biggest concern will be to be able to keep the fridge and freezer running and to have a washing machine running once a week.

Thank you for your help !!


r/SolarDIY • • 1d ago

Battery Usage settings recommendation: Primary use for Power Outage

1 Upvotes

I have a grid tied / NEM 11kw solar system at my house. After a lot of back and forth with myself I picked up two Ecoworthy Cubix100 batteries for the primary purpose having power / being able to leverage my solar during outages. I have no TOU plans for my utility and very favorable NEM agreements (1-1). Power outages are rare, but Ill admit recent media actively pushed me over the edge. I have a Growattt SPH 10000 TL.

I'm not exactly sure what to do for my inverter logic.

Options in my mind are

  1. Keep batteries at 100% and leave them. Pros: ready for power outages. Cons: Leaving batteries at 100% for an extender period of time seems unwise. Dont actually use my batteries :(

  2. Keep batteries at 50% and leave them. Pros: great for battery heath. Cons: i start at 50% power in an outage. Dont actually use my batteries :( I have a generator that I can charge the batteries back up with if power goes out at night.

  3. Despite having no financial benefit, program in a standard TOU time. Keep my batteries exercised and give some benefit to my local grid. Keep batteries cycling between 20-80% (?)

Open to ideas. TIA


r/SolarDIY • • 1d ago

Need Help With Cooling

1 Upvotes

So I’m looking to build a solar cabinet of sorts. It’s a 27” x 24” x 24” cabinet that will house all of the components for an off-grid system. My biggest concern at the moment is heat and cooling. Obviously I need venting but just having vent holes is not sufficient enough. I can add exhaust fans brining air into the cabinet on the bottom and out of the top with little issue but I’m concerned it still will not be enough.

Has anyone used a thermoelectric Peltier module to cool a cabinet and if so how did that work? How much cooling did it actually provide? Or if you have any other ideas for more effective cooling please let me know. Thanks!


r/SolarDIY • • 1d ago

Will a 1000w power bank run my refrigerator? Short answer NO!

0 Upvotes

Or maybe the Darwinism answer is yes.


r/SolarDIY • • 1d ago

Aferiy p280 p300 available when?

1 Upvotes

The p280 and p300 were both down to just over $700 but sold out.

Anyone know when they will be back in stock?


r/SolarDIY • • 1d ago

More pics of the of Middle of nowhere system

Thumbnail
gallery
110 Upvotes

For those that wanted more pics, a month after the last set of pics I changed the system to 24v because with my panels I was limited to 500 watts with 12 volts at 35 amps.


r/SolarDIY • • 1d ago

How can I tell if my front door gets enough sunlight for a small solar powered device?

2 Upvotes

I'm in Minnesota and looking at getting a solar powered smart lock for my front door. The one I'm considering is the lockin solar face, but I've never owned anything solar-powered, so I'm trying to figure out whether my doorway would be a reasonable spot for it.

The lock has a small solar panel, and I'm wondering how much the shorter winter days, cloudy weather, and snow might affect charging. I'm also not sure how much of a difference it makes if the door gets some daylight but not much direct sun.

I haven't bought it yet, so I don't have the panel's output or battery details. I'll check those before ordering, but I'm curious what else I should be looking at. For a small device like this, how would you assess whether a location gets enough light through the winter? Would checking the battery level over time be useful?

If anyone has experience with small solar-powered devices in cold climates, I'd love to hear what you've learned.


r/SolarDIY • • 1d ago

To charge or not to charge

Thumbnail
gallery
21 Upvotes

I’m building an at-home DIY off-grid power supply and am at the point where I decide whether to fully charge my bank (Yixiang 16kWh) using a plugin charger, or connect the pieces (SUNGOLDPOWER 10,000W) along with power panel.

Should I charge the bank first then connect everything up, or connect everything and charge using panels over time? Note: I won’t be using the battery bank for probably a while. Like weeks to months.

if I go the charge first route, what kind of charger would be recommended? I bought a LiPo golf cart charger, but the specs say it’s set to 58.4V which from my research sounds too high for my battery bank.

Any advice would be appreciated. Thanks!


r/SolarDIY • • 1d ago

Lifepo4 Battery Mix

1 Upvotes

Hi guys,

I need some pointers... I have 2x 15kwh lifepo4 batteries connected in parallel to a deye offgrid inverter. Communication works perfect and all is well.

I now want to upgrade by adding a third battery (making 45kwh total) however, the manufacturer doesn't make this battery anymore. But now makes a 16kwh version.

I can't get a direct answer from said manufacturer if it'll work or not. Installers telling me it's not a problem... Sales agents telling me it's not a problem (ofcourse they would)

What do you guys think? Can I add this new 16kwh to the current battery bank and maintain a good bms data connection with the inverter


r/SolarDIY • • 1d ago

Is 400W solar enough for 3 fridges/freezers on a 3kWh battery?

5 Upvotes

Hey folks, been going back and forth on solar sizing for a home backup setup and could use some advice. I'm considering the Bluetti Elite 300, mainly for our shorter 2–3 hour outages. We already have a propane generator, but I'd like to rely on it less during longer outages, especially if fuel starts running low.

The main things I'd need to keep running are a kitchen fridge, a large upright freezer, and a chest freezer. Maybe some lights and phone chargers too.

I was originally looking at the bundle with 2x 200W panels, but now I'm wondering if I'd end up regretting not going bigger from the start. With 4–5 peak sun hours, I'm guessing 400W might only give me around 1.2–1.6kWh on a decent day after losses. Not sure that's enough to keep up with three cooling appliances, even with the compressors cycling on and off. Would 800–1,000W be a more reasonable starting point? Or should I measure the actual daily consumption before even thinking about panel size?

The other thing I'm stuck on is the solar input. It's a single MPPT rated for up to 1,200W, but limited to 60V Voc and 22A. Would parallel panels make more sense here? I'm also trying to figure out how much headroom to leave for cold-weather voltage increases.

Anyone running a similar fridge/freezer setup on solar? Curious what your actual daily usage looks like.