Clock spring issue or bearing? Also rattles when driving from vibrations.
1995 R33 gtst
r/SkyLine • u/kttay916 • Jan 27 '26
Hey skyline community!
I hope everyone is doing well. Wanted to swing by and give everyone a quick update. While taking the mod seat I got some auto mod loaded inside the community to cut down on scam or spam inside the community. However, with that not everything is perfect. Certain post do get caught in the auto mod Que and get auto deleted which shows as “moderation team has deleted your post”. Mostly triggers with newer accounts and low karma posts which bots fall under. This also happens with comments as well.
If you happen to see that please shoot us a mod mail and we can push it through. We have no issues helping you post/comment. Hopefully this clears up some confusion for any member wanting to post/ comment.
Always reach out to us and also let us know how to improve the community or add to it!
P.S winter snow pic of my car for your viewing pleasure
r/SkyLine • u/InstructionSquare894 • 1d ago
So my r32 20det sounded like someone breathing rasply, would try to die while driving sometimes succeed, not idling right, stalling, I changed the MAF it was worse puffing out black smoke jerking when winding up boost, swapped the maf back to the original, (did a ecu reset everytime)
Was driving mint maybe something was loose also took the seal from the clearly faulty replacement, but after a good 40 minutes of driving and a decent boost it decided to start chugging trying to die, i had to pull over to let it stall, started algood got it home.
The next day no issues for a good 40 minutes until I came up to a roundabout and it stalled wouldn't turn over for (what felt like forever as I was blocking traffic) but was probably only 4 minutes, finally got it going, headed for home and was trying to die the whole way home had to pull over once to let it stall, im taking it to the shop on tuesday for them to read the ECU, but any thoughts on the issue tho? Boost leak, vacuum leak?
r/SkyLine
•
u/stockf87
•
3d ago
Just picked this up around May of this year, re-done in bayside blue
r/SkyLine • u/ObjectiveAd9242 • 4d ago
Guys I’m so close but I cannot get these last two nuts off. What were some tricks you’ve used? My wobbles won’t get it, box wrench can’t seem to get it, I’m absolutely dying.
r/SkyLine • u/ObjectiveAd9242 • 4d ago
Decided to pull the front pipe just to see. Lo and behold what was sitting in the cat.
I’ve got a spare set of turbos I may just swap them for fun while I wait on the head to get done being built. Fun times.
r/SkyLine • u/GabRB26DETT • 5d ago
r/SkyLine • u/AJ_Pimpsner • 6d ago
r/SkyLine • u/scrubberducky93 • 6d ago
I bought the car with a built engine tuned to 500hp. I would like to switch the intake plenum from the stock to a Nismo/Nismo style one like Greddy or something like that. I assume I would need a retune as it's going to change intake air balance but I'm just looking reassurance that's the right direction to go.
r/SkyLine • u/Super-Permission-850 • 6d ago
I’m looking to buy a seat of Nismo seat covers for my R33 GTR but I’m seeing multiple photos where they show wrinkles after install. Do these ever go away as they settle? Does anybody have any other pictures? I’ve attached what I found. Product reviews seem to be very limited
r/SkyLine • u/Late-Letterhead6888 • 7d ago
Hello just posting this ask if this would be a good deal/idea to cop this car for 16k. I really don’t know much about cars but I’m trying to see if this is okay. TYIA
r/SkyLine • u/HASHIRSIDDIQUE05 • 6d ago
Do comment guyss
r/SkyLine • u/Thorphax • 7d ago
I was asked yesterday to post steps on how to replace burned out bulbs on these OEM head units found in R32s, so here I am doing just that on mine.
First you're going to want to buy a pack of 3mm 12v halogen bulbs, I went with these ones:
https://www.amazon.com/dp/B0DS59PHY3
You're going to need these tools:
Philips Screwdriver
Tweezers
Wire snips
Soldering Iron
Solder
Solder ribbon or Solder vacuum gun (for cleaning solder pads)
8 of the new bulbs
Now the steps on disassembling the front panel of the unit and replacing bulbs, following the images:
1- After you have extracted the head unit from the car, undo the two screws that hold the front plastic on either side, and pull out the volume knob (it will just come out if you pull on it). Then gently push down on the lock plastic tabs just above those screws on either side, and pull at the front cover.
2- Don't worry about wires, the whole front has a direct-fit connector that will just pull out, very convenient.
3- Next when looking at the back of the PCB for the front panel, there will be 4 small screws, you're going to want to remove those
4- Here you can see the PCB unscrewed from the plastic front fascia, it will just come right up, be mindful of the plastic tab at the bottom which holds onto a lip on the PCB so you don't end up snapping it, just pry it gently. You will see a transparent plastic thing here surrounding two bulbs, you will need to pry this off to access two of the bulbs' backs underneath, its very easy, just push on its front pins and pull from the back, it will come right up.
5- And here is the front of that PCB with its VFD display, buttons, and the blue sleeved bulbs (what you're here for).
PS: Be very careful with the VFD display, these are vacuum sealed and if you break that seal, that's it, there is no fixing it, that whole VFD will be trash.
6- Each little bulb has a blue silicone sleeve over it (to make the light whiter), and is held in place by two solder joints on either side of its plastic enclosure. You're going to want to use a solder iron to heat up the solder and tweezers to pry up the little bulb wires out of the solder.
7- Once you do that, just push on the bulb while pulling on the plastic enclosure, it is just clipped in place, and it will come right up.
8- Here is the new bulb from Amazon, they're slightly longer than the original ones but fit just fine, this is probably the max length for these, any longer and it won't fit, keep that in mind
NOT PICTURED: I used a solder vacuum gun to clean up all of the pads from old solder, you can do the same thing with solder ribbons and your solder iron, its important to clean them up and use new solder.
9 and 10- Now what you will want to do: using snips, clip the old bulbs wires and then pull them out of the plastic enclosures, then use your fingernails to pry off the blue silicone sleeves off them, then push the silicone sleeves onto the new bulbs and fit them down snug, then push the wires of the new bulb through the plastic enclosure little holes until the bulb is fully seated. Finally you push the assembly back onto its original hole, and bend the bulb wires over the solder pads until they sit down against it good enough, then use new solder and the soldering iron to resolder them on the board, and use your wire snips to cut off the excess wire off the bulbs.
11- Repeat that until you have done all of the bulbs. There are 8 of them total, and yes you will want to replace all of them even if you have a few that are still working. It keeps them all shining consistently and saves you work later when the old working ones eventually also burn
12 and 13- And that's it, you're done! Just follow the steps in backwards order to put it back together and reinstall it in your car. Here are pictures of it in mine with the new bulbs shining nicely through the fascia.
I hope this is helpful to some of you, I know its not a super pristine and precise tutorial on how to do these (I am super sick with the flu, I'm sorry lol), but hopefully its somewhat straightforward :)
If you have questions ask them below.
r/SkyLine • u/MisterDrew1994 • 9d ago
Got these three beauties today! ❤️
Sorry, I do not own a real Skyline.