r/Skookum • • 11h ago

350 Timing chain desk lamp

157 Upvotes

Hi all, Im a mechanic by trade, and recycle what I can into something different. I enjoy making models, lamps, figurines and more.


r/Skookum • • 3h ago

I made this. Fuel pump lamp

34 Upvotes

Hi all, Im a mechanic by trade, and recycle what I can into something different. I enjoy making models, lamps, figurines and more. Thanks for looking. This lamp is made from a fuel pump.


r/Skookum • • 2h ago

Need help plz Hardfacing a Wildcat

Post image
21 Upvotes

Adding hard face on the wildcats on an anchor handling tug (AHTS) at sea somewhere. Our boat usually works subsea, but a job came up where we would need to move a lot of heavy chain. For that we use the wildcats. They had been neglected for a while, so my colleague decided to spend 12hrs straight on this one; welding multiple packets of wear rods and smoothening the link-pockets. Being a welder myself I appreciated his effort and I supported him the best I could. Our main winch does +500t pull and the wildcats sits on the same shaft, not sure their exact rating though. They weigh around 5t each so preheating was a bit uhm ok forget it for a bit ok let’s just weld this shit. 12hrs later you couldn’t even fry an egg on them.


r/Skookum • • 11h ago

I made this. Dipping my toes in the water here

Thumbnail
gallery
27 Upvotes

Hi all, Im a mechanic by trade, and recycle what I can into something different. I enjoy making models, lamps, figurines and more. Here's a few of my creations, thanks for looking! Hope this stuff qualifies!


r/Skookum • • 1d ago

I was told that my Drill is pretty Skookum.

Post image
159 Upvotes

r/Skookum • • 2d ago

Mindblowing shit! Ridiculous scales from the vessel I worked on

Thumbnail
gallery
232 Upvotes

Former Marine Engineer on a Anchor handling vessel (lifting anchors off the sea bed for rigs)

But also pulling them out to sea and removing old wires from seabed.

The scale of the components on these ships are just ridiculous. Everything is huge compared to... Basically anything.


r/Skookum • • 5d ago

OSHA approoved The most satisfying power tool switch ever

Thumbnail
gallery
177 Upvotes

I should probably replace this 1940’s vintage motor starter/circuit breaker on my bandsaw but those start and stop buttons just feel so satisfying to press, they have a gravity to them.


r/Skookum • • 10d ago

Automatic rope decoupling rail, dual steel clamps, and four track cables anchored at 70 tons of tension each inside a 3,883m alpine ropeway station

186 Upvotes

r/Skookum • • 10d ago

Vertical Drag Finisher Honing the Cutting Edges on Steel Alloy Bone Taps

0 Upvotes

A little precision finishing action from our shop!

These steel alloy bone taps are being processed in a Vertical Drag Finisher to create consistent cutting-edge radii without compromising the tool geometry.

The tools are mounted in rotating holders and dragged through finishing media for controlled edge preparation.

This was part of a customer evaluation for a dental implant manufacturer in Brazil.

Figured you folks might appreciate seeing the machine in action!


r/Skookum • • 14d ago

Mindblowing shit! Photonic Induction is back!

119 Upvotes

r/Skookum • • 21d ago

TIL Grinder discs have an expiry date, as the resin binder breaks down over time, increasing the chance of shattering. Throw out those old discs!

261 Upvotes

Also it's best not to store them where they are exposed to excessive heat or humidity, like the toolbox in the bed.


r/Skookum • • 21d ago

Mindblowing shit! River Don Engine - The most powerful steam engine still running

Thumbnail
youtube.com
11 Upvotes

r/Skookum • • 24d ago

Old jeans

Thumbnail
gallery
75 Upvotes

Used old jeans to make a bib for an old 4x6 welding hood


r/Skookum • • 26d ago

Edumacational Dan Gelbart - Wisdom on patents in the Age of AI

Thumbnail
youtube.com
73 Upvotes

r/Skookum • • 26d ago

3 weeks building a horizontal drag finishing machine, condensed into 90 seconds

10 Upvotes

We recently finished building this horizontal drag finisher at our facility in North Kingstown, Rhode Island.

The machine uses rotating work holders to move parts through finishing media for grinding and polishing applications, including gun barrels and other long components.

The entire build took about three weeks, and the completed machine is now headed to Wisconsin.

Thought this community might enjoy seeing how it came together!


r/Skookum • • 27d ago Bravo

Edumacational Bell & clock guy rambles about the evolution of bell & clock systems over time [OC]

Thumbnail
youtu.be
44 Upvotes

r/Skookum • • Oct 18 '26

OSHA approoved The hardest part is to let go...

Post image
225 Upvotes

3 years of hard work


r/Skookum • • Oct 17 '26

The Khyber Pass boys finally have some competition.🥀🥀🥀

43 Upvotes

r/Skookum • • Oct 14 '26

Some air.

43 Upvotes

Storage cylinders from a compressed air plant I used to have in my garage. Yes, that's 3800 PSI on the gauge. The air was clean and dry - I used it for scuba diving among other purposes.

Unfortunately, the plant had to be disassembled and sold for parts when the compressor failed and could not be economically repaired.


r/Skookum • • Oct 11 '26

I made this. Turboencartulator: Turbine Runs

Thumbnail
youtu.be
26 Upvotes

I took the cart up to my parents place last weekend and had issues so I couldn't do any drive bys with the engine running. I fixed that issue as we as installed new shocks and rear bushings and took it out today to drive it around a bit. I think I used about a gallon of fuel here. It's thirsty.


r/Skookum • • Oct 06 '26

Kelvinator Refrigerator

Thumbnail
gallery
97 Upvotes

I picked this up on marketplace for 20 bucks! Its built like a brick shithouse, the latch is the most positive feeling latch ive ever felt. It weighs north of 200 pounds, I can see how Indiana Jones would have survived a nuke in one of these.

The r12 ran out so i replaced it with hfc152 which is can dusters. Its runs great and sips power.


r/Skookum • • Sep 26 '26 Bravo

Mindblowing shit! Installing 14 bells

Thumbnail
gallery
501 Upvotes

r/Skookum • • Sep 20 '26

Duel shield .045 wire tips?

Post image
33 Upvotes

r/Skookum • • Sep 13 '26

CVT with one connecting rod

Thumbnail
youtube.com
13 Upvotes