I’m looking for one for a project. I’m wondering what the going rate would be for a used genuine 41mm DJ 126344 If anyone has or knows where to get one, it would be greatly appreciated
I'm sharing a short video from the disassembly of a VR3285 that I've recently done. This is part of a project build that I have been doing and I just wanted to share the breakdown of the movement. I am currently editing the assembly of the movement and will share that once I have it finished. This is my first foray into recording and sharing my work, so I'm still trying to figure out how to record from overhead and not impede the video or my work while doing it. The only thing I didn't record was the removal of the balance jewels and the escape jewel in the mainplate since those were done using my stereo microscope and I didn't have the ability to record that at the time.
I posted a few years ago looking for advice on repairing my Clean 126500- the crown stem when screwing down is incredibly gritty and gets worse each time.
I’m assuming the threads on the crown stem and case tube don’t line up or something.
I’m hoping someone could point me in the direction of a spare setup. I’m also super open to paying someone to repair the watch. It’s beautiful and just sits there in my case because whenever I wind it it feels like it’s breaking.
the movement works great, and everythings perfect but screwing down the crown.
thanks team - any advice or service offers appreciated
Just got my 12 QC photos and 2 videos from TheOneWatches for a RICHF GMT-Master II 126710GRNR ("Bruce Wayne") on the Oyster bracelet with the JH3285 free-sprung movement ($758, per order spec).
Before asking for human eyes here, I ran an experiment using Gemini to do a structured first-pass QC to see how thorough it actually is. Sharing my workflow, what it checked, and the follow-up questions it drafted for the TD so you guys can weigh in on both the watch and the method.
How I Got AI to Run the QC
Instead of just dumping photos and asking "GL or RL?", I stepped through it like this:
Set the criteria first: I shared the order spec first and asked it to list every quality check it would validate before seeing any QC media (index alignment, dial print, rehaut, bezel color split/action, cyclops/date centering, hand stack, SELs, clasp, lume, and timegrapher tolerances).
Batch-uploaded everything: I uploaded all 12 QC photos and both videos across two messages, telling it not to analyze until the full set was in so it could cross-check across angles and video frames.
Gen comparison pass: After getting the QC breakdown, I asked it to compare my specific QC shots against a genuine 126710GRNR so I could separate normal factory tells—slightly flatter grey ceramic (IMG_4924, IMG_4922), sharper black/grey split at 6 and 18 (IMG_4924, IMG_4922), slightly tighter 12 o'clock triangle gap to the minute track (IMG_4924), and mild blue cyclops AR glare at tilted angles (IMG_4924, IMG_4923)—from actual RL-worthy defects.
Sanity-checked its assumptions: I pushed back on a couple of things—like whether it actually heard the bezel in the videos (both videos were muted and the bezel was never rotated) and whether the extra movement/clasp checks meant having the TD physically open up the watch.
Index Alignment & Dial Printing: 12, 6, and 9 markers sit straight and centered over the minute track and the 6 o'clock crown; crisp white and green "GMT-MASTER II" text with no visible dust (straight-on dial photos: IMG_4924, IMG_4922). Rehaut crown sits centered at 12 (IMG_4924, IMG_4923).
Bezel: 12 o'clock triangle aligns cleanly; black/grey split bisects the 6 and 18 horizontally with clean platinum-tone fill (IMG_4924, IMG_4922).
Date Wheel & Cyclops: Checked across 18 (IMG_4924, IMG_4922) and 18 → 19 → 20 (function video: NOLI1110_batch.mp4)—all centered cleanly with crisp font. Slight cool/blue AR reflection at tilted angles (IMG_4924, IMG_4923).
Hands & Movement: Correct hand stack (hour → GMT → minute → seconds) (IMG_4924); smooth 1-hour jumping local hour hand and clean midnight date flip (function video: NOLI1110_batch.mp4).
Case, SELs & Clasp: All four SEL corners sit flush with no noticeable gaps (IMG_4924, IMG_4922, caseback shot: IMG_4931); clean case profiles and crown guards (IMG_4925, IMG_4926); bracelet finishing looks solid (IMG_4927, IMG_4928); closed clasp coronet and seams look tight (clasp photo: IMG_4929).
Timegrapher: -1 s/d to -2 s/d, 282°–284° amplitude at a conservative 52.0° lift angle, 0.0 ms beat error, 28,800 vph, clean flat trace line (timegrapher video: XPJJ0883_batch.mp4).
Follow-Up Questions AI Suggested Asking the TD
AI gave it an overall GL, but flagged four items missing from the initial 12-file batch and drafted these follow-up requests for the TD:
Open-caseback movement shot: Focus on the balance wheel to visually confirm it's actually the JH3285 free-sprung movement (no regulator arms) rather than relying solely on the stickers (IMG_4924, IMG_4931), with a reminder to tighten the caseback properly afterward.
Bezel rotation video (with sound on): Rotate both directions to check click crispness, alignment, and backplay when settling at 12 (neither NOLI1110_batch.mp4 nor XPJJ0883_batch.mp4 touched the bezel or had audio).
Lume shot: Dark-room photo to verify even blue Chromalight glow across all indices and hands.
Open clasp blade & Easylink photo: Check inner clasp engravings and the 5mm extension (non-invasive, no tools required).
Questions for the Community
Do your human eyes spot anything on this piece that AI missed?
For those who've bought free-sprung JH3285/DD3285 pieces from Steve/TheOneWatches: would you bother asking them to pop the caseback open to verify the balance wheel, or leave the factory seal/gasket untouched and just ask for the bezel, lume, and clasp checks?
On the verge of ordering another new restomod build using a Green Meteorite dial that was proposed to me. Base template dial will be the 6239 Paul Newman dial with the Lollypop subdial markers . Torn if I will go for the Black or just plain green Meteorite subdials 🤷🏻♂️ ? What’s your pick ?
I have a franken 16610LN. The dial is a 'SWISS MADE' Sillan, hands are gen and there is a noticeable mismatch between the daytime colour of the lume. The gen hands are superluminova and are bright white in colour. The lume on the Sillan dial is a creamy/green colour. I am considering reluming the markers on the dial. I have no experience with this and will be practicing on a trash BP dial I have lying around. I am wondering does anyone have any experience with this and/or are there any tutorials available online.
I am aware I will need to remove the hour markers and scrape out the old lume before attempting to relume. It seems like it will be a difficult thing to do, based on what people say. Nonetheless I still want to give it a go.
This DD3235 movement arrived completely non-running, bone dry, with a destroyed hair spring from a screw that had gotten into it from the case clamp. I swapped out the hairspring with one I had on hand, and gave the rest a full service. I love that rush of getting it on the timegrapher and seeing results like these!
Hey guys, need some help with my VSF Omega Seamaster 300 with the 8800 movement.
I removed the crown and stem because it wasn’t doing mild griding, but now when I try putting it back in, it won’t lock into place. The stem goes in but pulls right back out.
Not sure if I messed something up when pressing the release button or if something inside the movement shifted.
Has anyone experienced this before? Is this something that can be fixed easily, or am I looking at a movement repair? Any advice would be appreciated. Thanks!
I have purchased several reps, I always shoot for the best versions. I bought a 5711 patek and after having it for about a month it just stopped ticking. Every watch store says they do not service reps, and if they do they say its 1000 or more when clearly it would be better to just buy a new one. Has anyone ever found someone that will look at these? Or if something breaks are you just screwed?
When winding this piece the rotor starts moving . Died on my wrist something is wrong with it - where do I send it to get fixed . And how much do you think it will cost .
So I have this day date and I need to figure out if I should send it to a watchmaker for fixing or if I should do it myself. What should I do considering it could be just some loose screws.
I just received this beautiful watch and paid for deep crystal, but as you can see, I received that little package that says “deep” on it. When I opened it, there was a crystal inside. i sent a message to TD. Factory RCF
DD3285. The date isnt switching right away. The date starts changing halfway at midnight and then finishes advancing around 2 AM
I assemble watches often, but I dont open up movements. Willing to give it a try so long as im not getting too deep into the movement. Is this something I could fix myself?
My watchmaker is on vacation, and I cant been find anyone in the area in Mississauga, Ontario who services reps at a reasonable price
Hey everyone, I’m in a bit of a bind with my VSF Aqua Terra 38mm. The crown got stuck, and after applying a little extra torque, it completely snapped off. I’ve managed to remove the stem from the case, but I’m struggling to source replacement parts online and my TDs haven't been able to help either.
Does anyone know where I can find the right spare parts, or should I just look for genuine ones instead? Any advice would be greatly appreciated!
For those of you working on vintage builds, what aftermarket bracelets have you had the best luck with? Seems like there’s a pretty big difference in quality out there, especially when it comes to end-link fitment and how much play there is between the links. I’ve come across OystersJubilee and a few other options, but I’m curious what people who actually work with these bracelets think. Any brands you’ve been impressed with? Or ones that looked good in photos but turned out disappointing?