r/RacketStringers • u/Low-Ocelot-9667 • Oct 18 '26
is this normal????
It’s only been around four days of using my freshly strung racket, but I noticed that my strings have been moving far too quickly compared to before. Like, after a long rally or a powerful forehand or serve, I have to adjust my strings as there are columns that are so wide apart. The only difference is that I’m now using an 18 gauge Mach 10 vs my previously 17 gauge Mach 10 on my Ezone. In my previous setup, it took around 2 weeks or so for me to notice the string movement. They’re strung pre-stretched at 46lbs. I’m only a 4.0 player so I’m wondering if this is normal? Thank you!
1
u/Few_Lecture6615 Oct 21 '26
Why are you pre stretching mach10?
1
u/Low-Ocelot-9667 29d ago
My stringer told me that it’s to “remove the string’s excess flex, so the tension lasts longer and the strings doesn’t go soft right away.”
1
u/Few_Lecture6615 29d ago
He's technically not wrong, but you're destroying the snapback of your strings before you even hit the ball.
Essentially he is doing the softening for you.
1
1
u/theg4ylord Oct 21 '26
Do you use full bed mach 10? Do you notice any notching? Mach-10 is shaped poly, it shouldn't move around that easily unless you have a hybrid setup with another round poly. Also, the image you post is mainly applied for Multi strings, poly doesn't really fray.
1
u/Low-Ocelot-9667 29d ago
Yes, full bed. As for the notching, I don’t think there’s anything significant or anything at all.
1
u/theg4ylord 29d ago
I would check for a misweave, do you see any crooked strings or anything abnormal around the moving area? Also 46 is not that low, but still pretty low, which can also affect the snapback.
1
u/Early_Apple_4142 Oct 21 '26
The thinner strings inherently have more movement and due to that, lose tension faster as they stretch more. They will look more out of place than the previous 17g and also have quicker tension loss.
Is there a particular reason you're prestretching a poly? It's not super common practice.
1
u/Low-Ocelot-9667 29d ago
I see. But I don’t think it should move this early right? My stringer told me that it’s to “remove the string’s excess flex, so the tension lasts longer and the strings doesn’t go soft right away.”
2
u/Early_Apple_4142 29d ago
18g will move quickly. It’s a very thin string. That makes it softer and easier to displace. It would likely have better snap back if it wasn’t prestretched. With an 18 gauge all the elasticity (which isn’t much with a poly to begin with) was probably gone before you hit the first ball. In theory prestretching will create better tension maintenance by reducing the initial tension drop off the machine by pulling some of the elasticity out. Doing it on a poly ruins the benefits of the string.
1
u/wolvesight Oct 18 '26
pre-stretching your poly strings removes the elasticity that makes poly work to provide spin, and shortens the playable life of the string. Thinner gauges will see this effect more than thicker ones. Generally speaking, you don't pre-stretch poly anymore unless you are intentionally trying to pull out that elasticity (I've done it before to account for weather changes, as an example). A long time ago, a lot of players did pre-stretch their poly strings because the tech wasn't as understood and that's just what they had been doing for forever due to it being required for most natural gut.
1
u/Low-Ocelot-9667 29d ago
Just for the record, my stringer told me that it’s to “remove the string’s excess flex, so the tension lasts longer and the strings doesn’t go soft right away.”
1
u/Responsible-Side4347 Oct 19 '26
You are mixing up how multifilaments and polys behave.
Check the lab data from Tennis Warehouse University. Poly has barely any elastic elongation compared to multi or gut. Prestretching it on a machine doesn't "lock in" tension. You're just pulling out what little elasticity the string has left before it even goes into the frame.
I used to pull the string to get any coil memory out of it to make my life easier. In doing so I remove some of the elasticity the string has. Its plastic. It just stretches and stays stretched. I no longer do it. Mutifilament are a different matter and I prestretch them as tension creep decreases giving the stringbed a longer performance life. Does not happen in polys.
The factory already heat-sets those polymer chains when they extrude them. Yanking it hard on a pull doesn't help; it just ruins the fresh string.
If you want to manage tension loss, just pull it on a proper constant-pull machine or go up a pound or two on the reference tension. Prestretching poly is a waste of time that just ruins the playability.
1
u/wolvesight Oct 19 '26
no, poly will stretch around the ball on contact, which is the main benefit of poly. the amount of time that it stretches is one of the main defining points between different models. If the string snaps back faster, more like multi or synthetic, or slower will make the string feel "firmer or softer." that elasticity can and will be "pulled out" by pre-stretching the string. it's just like any piece of plastic; if you pull, twist, or bend it enough, it doesn't return to the original shape. The same thing happens to the string after hitting so many shots, the string doesn't expand and contract in the same way anymore. By pre-stretching a poly string, you will remove some of that elasticity, which makes the take on a "firmer" feel on contact, and reduce the amount the string moves; not just side to side but how it flexes around the ball on contact.
1
u/Responsible-Side4347 Oct 19 '26
Your explanation is conflating elastic deformation with plastic deformation. 2 distinctly different things.
Polyester is a semi-crystalline polymer. Unlike natural gut or nylon, poly has a very narrow elastic limit (around 3–4% maximum elongation).
When a ball hits an unstretched string, the string stretches within its elastic zone and snaps back. However, prestretching poly forces the material past its yield point and into the plastic deformation zone. In layman's terms, it gets stretched and looses some of its original performance. Its why the property is visual when you bend it and it stays bent.
When plastic deformation occurs, two things happen scientifically:
Micro-Yielding: The polymer chains are permanently displaced. Plastic deformation does not bounce back. Once you pull that length out on a machine, the material cannot return to its original state.
Loss of Workability: By mechanically forcing plastic deformation before the racquet is played, you consume the string’s mechanical fatigue life prematurely.
The user isn’t getting "custom flex." They are mechanically wearing out the polymer chains. You are left with a string that has a spiked dynamic stiffness, degraded tensile resilience, and a drastically reduced performance window.
If someone wants a stiffer stringbed or less initial tension drop, they should string a pound or two higher or use a stiffer poly profile. Mechanically over-stretching a polymer just degrades the material’s structural integrity.
This is well documented.
2
u/Secret-Gas-6524 Oct 21 '26
I only know poly and natural gut. Poly notching is the deciding factor. Natural gut fraying.
1
u/vnyrun Oct 21 '26
Thinner gauge is much more noticeable when they don't snap back as much (and drives me nuts when they aren't as straight). Makes sense bc they are effectively less stiff. Mach 10 also has a coating that wears away so maybe that makes it a bit more noticeable? Either way 4 hours is really soon.
7
u/DeaconFrost613 Oct 18 '26
Notching is the indicator I would use for all types of poly.
Stop prestretching anything but gut strings, please!