r/RCPlanes • • 8h ago

First weekend with the 70mm Viper!

22 Upvotes

I got this plane off Facebook marketplace a while ago but never flew it till now because I didn’t have a good place to fly it and I was too scared lol. I finally mustered up the courage to fly it this weekend and it’s so smooth!

I definitely came in WAY too hot and from way too high up but I haven’t figured out how to judge how close the plane is with respect to the tree line because I’ve lost a plane in the past thinking I was ahead of the trees when in reality I was behind them 😅

But overall very smooth and fun to fly and handles pretty nicely.


r/RCPlanes • • 16h ago

Balsa USA Smoothie Part 1

Thumbnail
gallery
34 Upvotes

Recently, I got the itch to start building again. While walking my dog I encountered a guy loading some foam planes into his car. We talked briefly and he invited me out to the local field. My daughter and I had a blast watching people fly their models so I decided it was time to renter the hobby. I’m purchasing a trainer for the family to play with but I am going to work on this kit I have had living under my bed for almost a decade.

The last time I posted on here I was building the Tiger 2 designed by David Patrick. I didn’t get very far once life got in the way. This time around, I am determined to finish. So far, I have completed the two main wing panels. Next, I will need to form the main structure of the wing. I am going to follow the designers advice and go off plans and add camber so the plane doesn’t look droopy.


r/RCPlanes • • 19h ago

First attempt at a 4 engined micro

Post image
20 Upvotes

My first aircraft under 150 grams. Using a fsct6b paired with an r6b reciever. With a 550 mah 1s. Using the boost mod to make it run on 1s lipos. Have another 1s 1000 mah on order!!!!


r/RCPlanes • • 13h ago

Is there a way to make an old tx like the fs ct6binto a sleeper?

2 Upvotes

I wanna make it so that my old ct6b is upgraded to being a sleeper. Full telemetry, 1km+ range, and a digitial display plus the ability to connect to multiple receivers and in built battery plus circuit. Has anyone ever done this sorta thing


r/RCPlanes • • 1d ago

Hung this lesson board today

Post image
71 Upvotes

Some lessons are free, don't even cost a scratch. Some however, are a total loss. Here is my lesson board over the past year of flying. Flew everything from flite test foamies, nitros to 7 foot 55cc yaks.

Ironically the most fun and longest surviving plane was the flite test explorer.

I've left some room for more lessons to come.


r/RCPlanes • • 11h ago

Mini Aeroscout controller board?

Post image
1 Upvotes

Just to preface - I don't know anything about RC planes but I do fix electronics. Someone has asked me to fix this AeroScout and it looks like this transistor is blown near the input power.

Does anyone know what this part is? Or if this is a fairly common problem? I'd like to fix this so it can fly again.

Thanks to anyone that may have some insight!


r/RCPlanes • • 1d ago

04pro negative modifier

Thumbnail
gallery
6 Upvotes

Couldn't find an 04 pro nose cone for the drone im making so modified a blank one. Created a negative modifier in fusion that should theoretically work on most blank nose cones. Snug fit that slides in but doesn't move freely.​

Gonna test it with a few other nose cones and see if there's any issues.

Maybe someone's done it before but thought I'd share


r/RCPlanes • • 1d ago

I won these from a good will auction. I thought they looked sort of interesting, and they had no bids. Did i do good?

Thumbnail
gallery
54 Upvotes

r/RCPlanes • • 1d ago

Nouveau jouet

Post image
6 Upvotes

Pc-21 sebart


r/RCPlanes • • 1d ago

Trainer for a 6 year old.

4 Upvotes

Hi all,

6 year old son has a massive interest in planes and has asked for an RC plane from father Christmas.

I've been using RC for close to 40 years but mainly cars and more recently quadcopters and fpv quadcopters. No plane experience.

6 year old has pretty good dexterity and can handle cars very well and plays every plane simulator he can get his hands on.

Been looking at the models below.

volantex ranger 600

skyking f959s

Any thoughts? One better suited for beginners?

Any alternative suggestions?

Many thanks :)


r/RCPlanes • • 1d ago

broke tx antennae wire

2 Upvotes

I dropped my el cheapo transmitter and snapped off the antennae, is that wire anything special or can I just grab some similar gauge wire and solder on a new one?


r/RCPlanes • • 1d ago

SAFE settings with EdgeTX and 4-in-1

0 Upvotes

I've got an Aeroscout, a TX16s MK3, and a 4-in-1 module. I'm trying to program my switches for the SAFE/AS3X modes, but I'm having issues. I'm looking at the flight mode telemetry. I've discovered that changing flight modes seems to be a combination of channels 5 and 6. By doing some silly stuff on the Mixes page, I've got it going between "5 AS3X Level", "2 AS3X Envelope", "3 AS3X Heading", and "1 AS3X Level".

Which mode is which? Am I missing some modes? When holding it in my hand and rolling it back and forth, the least aileron deflection seems to be happening in Mode 2 (Envelope) and Mode 1 (Level).

Looking at the "SAFE Limits" in the DSMTools telemetry, Mode 5 has the lowest angle limits and highest gains, so I assume that's the "SAFE" mode. Mode 1 has the next lowest gains, but the highest angle limits. Modes 2 and 3 have the lowest gains and their gains are the same. Modes 2 and 3 have different angle limits, though.

Can anybody make sense of this mess? I looked at the wiki, and it said there can be up to 10 flight modes on the receiver, but didn't say which mode was what.


r/RCPlanes • • 1d ago

Receiver for Avanti 70mm v3

1 Upvotes

Just ordered an avanti 70mm v3 and looking for some advice on receivers. I have a spektrum AR631+ and am a little worried it may not fit. anyone have any experience? I'm a little worried about going with a 630 and no external antenna.


r/RCPlanes • • 1d ago

Is this battery fine to use?

Thumbnail
gallery
6 Upvotes

I am experiencing an issue with my drone(didn't happen before yesterday) i.e.

When fully charged, the flight goes well for about 5 seconds and then the drone slowly descends and after which it isn't able to take off even though props are spinning.

the battery has been swolen since 2-3months but this issue started yesterday.


r/RCPlanes • • 2d ago

Zipper V1 Hotliner

15 Upvotes

Several aerodynamic updates and she flies great!


r/RCPlanes • • 2d ago

🛠️ Anyone have a good DIY helping hands soldering setup?

4 Upvotes

Looking for ideas for a cheap, homemade helping hands soldering station, mainly for soldering wires and connectors for RC electronics.

I saw a simple setup at a hobby shop that was basically a block of wood with two wooden clothespins glued or nailed to it. Seemed like a pretty clever solution.

Before I throw something together, I'm curious what everyone else has come up with.

Anyone have a homemade setup that works particularly well? Pictures would be awesome. Not looking for anything fancy or expensive, just something practical that gets the job done.


r/RCPlanes • • 2d ago

DIY static thrust test setup — am I doing this right?

Thumbnail
gallery
4 Upvotes

I'm testing a SunnySky X2212 2450KV motor using a pretty basic setup. The motor is mounted to a piece of wood resting on a digital kitchen scale that measures in grams.

So far, I'm getting:

- 3S: Approximately 1,000 g of static thrust

- 4S: Approximately 1,100 g of static thrust

I know the setup is cluttered and ugly, but I'm just looking to confirm that this is a legitimate way to measure static thrust and that I'm not overlooking something obvious.

Does this look like a reasonable setup for getting fairly accurate thrust measurements?


r/RCPlanes • • 2d ago

Easy modeling for RC planes parts

Thumbnail
gallery
20 Upvotes

Hi everyone,

I have recently published a free and open source FluidCAD package to easily generate common parts for RC planes; propellers, fins and wings.

FluidCAD -if you do not know- is an open source app for parametric 3D modeling.

You can test the package options here:
https://hub.fluidcad.io/@fluidcad/airfoils?model=parts%2Fwing.part.js

To use it, search for the package in the hub from inside FluidCAD and click install.


r/RCPlanes • • 3d ago

First self designed plane: SGS 1-26e

Thumbnail
gallery
43 Upvotes

Wingspan: 48in
Mass: 298g
3s 850mah
2205 2300kv
30A esc
radio master r84 receiver
4x 5g servos

This is my first totally self designed plane. also first hot wiring wing. I kinda threw the canopy together and haven’t made the cowling yet, but it turned out relatively good. Does anyone have tips for painting xps foam?


r/RCPlanes • • 3d ago

RC sound emulators. Cool or Nah?

97 Upvotes

r/RCPlanes • • 2d ago

Is it possible to swap the rotor in a 50mm FMS EDF?

3 Upvotes

Hi folks, I'm getting conflicting answers on this one, so I'd ask here out of curiosity: In case of FOD or other damage, can you swap the rotor in 50mm FMS EDF, or are they trash? I can see that the blades are sold separately (although out of stock on AliExpress), so I'm curious.


r/RCPlanes • • 3d ago

Found RC Plans

Post image
25 Upvotes

I’m a professional pilot and never have been into RC flying. Found this at my parents which was handed down from my grandfather. I guess he used to fly it. How hard would it be to get this back to flying order? Any value in trying to “restore” this?


r/RCPlanes • • 2d ago

Fun Fly OSP 103126

Thumbnail
youtu.be
2 Upvotes

r/RCPlanes • • 3d ago

New build Micro Antonov An-2 (600mm)

Thumbnail
gallery
147 Upvotes

New build - plans coming soon!

Very happy how this An-2 came together, it felt like a proper puzzle. With a takeoff weight of 205g, easy wing cube loading of 6.6, 600g of thrust on 3s LiHV 450 from an 1806 motor on this 5x5x3 it should be good for 6 mins of fooling around at close to 3:1 TTW.

Tail surfaces and ailerons are enlarged to almost 120% of the scale dimensions, I hope it can hover controllably :)

Usually I never paint my builds until after the maiden, but the weather is pretty bad at the moment so I went a little bit over board... Didn't have a banana for scale so the third pic is with an 8x6HD for comparison.

The shop I ordered the wheels from messed up bad so I made some dummy wheels in the right size for the photos. Couldn't wait.