r/MechanicAdvice • • 7h ago

Oil showing high on dipstick after fresh oil change & smells like gas

Thumbnail
gallery
176 Upvotes

It's a 2020 Toyota Tacoma SR 2.7 i4 with 77k miles

Did my oil change at 7k & noticed the oil smelled like gas... it's not super strong but when you get close you can smell it.

Then saw it's showing high on dipstick (it takes 6.2 qts & I put exactly that) I even left out about .1-.2 qts since it was showing high already.

I do drive short distances daily to and from work (10 min there 10 min back) & will occasionally go on a longer ride on the freeway maybe once a week or run errands for hours.. not sure if the short distances daily have something to do w the smell of fuel & if it's normal.

Any advice is appreciated!


r/MechanicAdvice • • 7h ago

Hand tightening oil filters, yes or no?

71 Upvotes

Sorry if this is a dumb thing to ask, I'm relatively new to the world of mechanics.

I did an oil change on my car for the first time a few days ago (2009 Prius), and the tool I had to get the oil filter off only loosened it, it didn't tighten the new filter on. So I go to get a tool that will help me tighten it, but the guy tells me that oil filters should be hand tightened, so as to not over-tighten them and damage something. But I've also heard that you should hand tighten it, then use a tool to tighten it an additional 3/4ths of a turn or so. Thoughts? I love my car and would hate to ruin it by being stupid lol.

Side note, but if anyone has any advice on how / where to learn more about mechanics, I'd love to know! I don't have the money for a class, but any YouTube channel recommendations or other things like that would be appreciated


r/MechanicAdvice • • 2h ago

My 99 Tacoma coolant question

Thumbnail
gallery
14 Upvotes

Hello guys! I’m not mechanically inclined at all but I try to do things to learn. My Tacoma has green coolant pictures below but I want to top it off. I purchased the one at autozone that had the label for my vehicle but it’s red.

Can I mix them? My mechanic told me I could but all online info ive read says no.


r/MechanicAdvice • • 11h ago

Driveshaft fitting - last try before I call in a mechanic!

50 Upvotes

Am I doing something wrong?

I've taken a video showing the splined shaft and the hole in the gearbox, does anything look wrong? I can't see a circlip, but I'm not sure what I'm looking at.

My next ideas are: break the axle away from the intermediate shaft so I can press directly on the intermediate, rather than swinging the hub to bang it in.

Or, undo the 5 bolts to remove the seal carrier and try to force it in. But I'm not sure if it's the seal which is causing the issue.

Any thoughts would be gratefully received!!

Car is a 2014 opel/vauxhall mokka 1.6 petrol


r/MechanicAdvice • • 4h ago

Broke off the lower bolt for a driver rear shock on a 2nd gen CRV

Thumbnail
gallery
9 Upvotes

So I’m doing a coworkers rear shocks and when I go to tighten the bolt back on it decided to break in half. I got one end out but need advice on removing the threaded side


r/MechanicAdvice • • 19h ago

Is this normal, or should I be worried?

Thumbnail
gallery
114 Upvotes

I drive an Audi A6 C6 Avant (type 4F with BPJ) from 2008 with a 2.0TFSI engine and a 6-speed manual transmission. Upon addressing an oil leak that turned out to be coming from the oil filter housing, I found a large gap between what I think is the bell housing and the differential(?) I'm an amateur mechanic, so bare with me if that is not at all what I'm looking at here.

To me it looks like the whole thing is coming apart, but from googling and some conversation with AI I suspect that the two semi-circular holes leading into the flywheel are normal, but I am not so sure about the big gap in that metal spacer that looks like its missing sort of, exposing the threads on the bolt. I also felt like this looks serious enough to not trust what the AI says, hence the question here.
I'm having a really hard time finding any images or info on how everything should look down here, do any of you have any experience with this specific car or just know in general how it should look, and what I am potentially missing here?

Please note that the oil dripping in the images are not coming from the gap on the picture, I have a leaking oil filter housing that makes the oil run along the outside of the engine to down here, I have tested and confirmed that no oil is leaking from the gap. I am not driving the car while in this state until I know if I'm cooked or not!

Many thanks in advance for any tips or insights in general.


r/MechanicAdvice • • 12h ago

2019 Honda civic LX

Post image
22 Upvotes

Replaced my spark plugs at 100k with aftermarket plugs I bought on Amazon. Car is now at 160k. So that means these spark plugs only had 60k miles on it.

Car took a shit on the highway the other day and engine code was misfire on cylinder 4. Tip of the spark plug was corroded and broken off…

Is this an indication of a cheap spark plug or larger issue? From what I remember the spark plugs I pulled at 100k looked way better than these and these have 40k less miles on them.


r/MechanicAdvice • • 4m ago

2020 Chevrolet suburban LT

2 Upvotes

Stupid, goofy noises. Serpentine belt and another thing possibly?

418,000 odometer (yeah I know)


r/MechanicAdvice • • 26m ago

Exhaust stud thread destruction

Post image
2 Upvotes

When taking the exhaust off my (1990 miata) car, the nut decided to take the stud with it. Metal coming along for the ride as well, so here’s my question; what do you guys do when this happens?


r/MechanicAdvice • • 4h ago

Would you get Mevotech or Duralast Gold?

Post image
4 Upvotes

Looking for replacement control arms, upper and lower, and steering tie rod ends. Autozone’s Duralast gold came out to about $800 for everything. I found this Mevotech kit (it’s their TTX line) on rockauto and it comes with everything that I got quoted from AZ plus the sway bar links for $600 not including shipping or tax. Which one would you go with?

Edit: to stay within the rules of this sub; it’s a 2016 Chevy Tahoe LT.

Added that it’s Mevotech’s TTX line


r/MechanicAdvice • • 4h ago

What is the best course of action from here?

Thumbnail
gallery
4 Upvotes

Lost my only keys for my 93 Ford F-250. Original had already been replaced with aftermarket which is there now, so locksmith told me he couldn’t cut a new key and suggested I just replace the part that would come with two keys.

Got a replacement ignition lock cylinder. There is a pin that needs to be depressed in order to slide the old one out. That pin cannot be depressed without the original key to rotate the cylinder to the on position. Internet suggested dropping the plastic cover and drilling out the pin, which I did. However, either my bit was too large or I went too far, because even after the pin was drilled out, the cylinder won’t rotate to the position where I can pull it out. Any ideas at this point?


r/MechanicAdvice • • 1h ago

2013 Toyota matrix check engine light on

2 Upvotes

Hi! I was wondering if it would be possible to go a month without fixing my car. The check engine light just turned on took it to autozone and it’s basically saying that I have an emission leak. I’ve already changed my gas cap so I doubt that it’s that. I have a 2013 Toyota matrix with 120000 miles. Unfortunately i have big expenses I need to cover before I can take care of the problem. I just use my car to work and back granted tho I drive a total of 100 miles a day 5 days a week. I’m not sure how much it would cost to fix the problem but realistically tho is a month too long to wait or should I figure something out sooner? Help is much appreciated.


r/MechanicAdvice • • 1h ago

Battery- Dead dead or more?

2 Upvotes

Hey all. I'm pretty sure my battery is caput, bjt wanted some input to know if I may have something else going on at the same time.

Have an optima red top in my 87 gmc. Battery is 3 years old, and unfortunately has sat for just about 2 years (maine winters too) in the truck.

Truck started fine 2 years ago. Battery I think is toast, as truck wouldnt start with a jump, battery would only hold about 12.4 when I slow charged it.

Question here is on amps I guess, which is something I'm not super knowledgeable about. Going that long, is it reasonable that the truck would not start with 12.4 volts on it, AND being jumped at the same time with another truck? That the battery was bad enough and acting as a big enough sink to not let enough juice through?

After the slow charge I hooked it up, and was jumping at the same time and I got it turning over decently, but the truck didnt even attempt to fire.

So in the end, my question would be (and I wouldnt be surprised) if maybe theres another issue such as fuel, or if it reasonable to say that a fresh battery with the amps required for it to turn over st the proper speed will get it started?

Just wanna be able to move the thing so I can get it where I want it to hopefully start digging into it to fix it up!


r/MechanicAdvice • • 5h ago

Gimme your best tricks rounded caliper bracket bolt

3 Upvotes

I've already tried an extractor kit and managed to destroy that. Penetrating oil for days. Locking vice grips. Grinding a flat edge on. It's right up against the axle ear and when I tried to use a hacksaw I accidentally nicked that a bit so I put it down. Used a hammer on the rotor to loosen it up. I think when I get off work I'm going to try pushing on the bracket to see if I can loosen it from that instead of the bolt. I am so over this shit, it's way too cold for all this. I'm replacing the caliper and bracket and the rotor.

Fiat 500 pop 2013


r/MechanicAdvice • • 4m ago

Cylinder 4 Misfire Only Under Heavy Load – Blinking CEL

1 Upvotes

2013 Audi allroad b8.5

I’m having an issue with a cylinder 4 misfire that only seems to happen under heavy engine load.
Here’s what it’s doing, Normal driving seems fine.
When I accelerate under heavy load, the check engine light starts blinking and I get a cylinder 4 misfire.
If I let off the throttle and slow down, the misfire stops and the CEL stops blinking.
I can drive at higher speeds and higher RPMs without any issues, as long as the engine isn’t under heavy load.
It seems to happen specifically when the engine is working hard, not necessarily at high RPM.
Has anyone experienced something similar?
I’m wondering what could cause a cylinder-specific misfire only under heavy load. Could it be a weak ignition coil, spark plug, fuel injector, fuel delivery issue, or something else?
Any advice or suggestions on what I should check first would be appreciated!


r/MechanicAdvice • • 24m ago

Help!

1 Upvotes

Recently swapped out the oil pump on my 01 Honda Prelude, H22, MT and now it making a new sound 😭 Before I take everything back apart any idea what could be causing it?


r/MechanicAdvice • • 4h ago

Starter barely cranks when hot - Cranks slowly in general

2 Upvotes

I have a 1999 Honda Civic EX and since I've owned it, the engine has turned over slowly when starting, but it has always managed to start. Recently, when starting with the engine already hot, it barely turns over and sometimes doesn't have enough force to actually spin the engine. But once I let it cool off for a while, it starts okay (but still slowly). Even when jumping from another battery, it still cranks the same.

The battery tested fine and the engine seems very healthy when running. Could it be an issue with the starter motor itself? I believe it is the original from 1999. Thanks


r/MechanicAdvice • • 38m ago

How much time do I have before I need to replace these 2018 bmw 640 gt.

Thumbnail
gallery
0 Upvotes

Somehow both my front axles look like this. BMW wants 3300 dollars to replace both axles. What are my options besides crying ?


r/MechanicAdvice • • 4h ago

96 F250 5.8 rough idle, occasionally dies at idle.

2 Upvotes

Warm starts also seem to be problematic. Gotta floor the throttle as if flooded.....thoughts?


r/MechanicAdvice • • 42m ago

Need help with brakes on Ford ranger 95 (audio on)

1 Upvotes

I can’t solve why my brakes are spongy I’ve bled them several times to make sure no air but still no luck and before I did this the brake booster and master cylinder worked good I replaced a brake in line the rear, brand new calipers, brakes, rotors, and did rear drum brakes and emergency brake cables. What can it be


r/MechanicAdvice • • 44m ago

Silverado compression issues after lifters changed.

1 Upvotes

Trucks been sitting for a year or so, I finally got around to changing my lofters after one was collapsed. I stopped driving immediately when it happened. But now when I changed my lifters, I have no compression on 2 cylinders. I changed all gaskets and all new lifters from 1A. 200~k miles. Silverado 08


r/MechanicAdvice • • 45m ago

Stubborn Head Gasket Material

Thumbnail gallery
1 Upvotes

r/MechanicAdvice • • 1h ago

BROKEN BOLT (what do I do?)

Thumbnail
gallery
1 Upvotes

This is a cv carb off a 1986 Suzuki savage 650

I already tried wd40 soak and turn the bottom with pliers and the bolt just crumbled

- do I just leave it there and use 3 bolts instead of 4?
Or
- how would you take this bolt out?


r/MechanicAdvice • • 1h ago

Thermostat for coolant

Post image
1 Upvotes

I have a 2016 Ram 2500 Laramie 6.4L hemi. Today I replaced the thermostat housing and believe I crushed the plug in that attaches to the housings sensor. Is there any easy way to replace that wiring and or connect? Everything is working fine except the gauge is still showing nothing and the digital read isn’t showing and error with an error for electronic throttle. I hope I explained this well enough (piece that connects into black portion)