r/Luthier • • 3h ago

Help!! my guitar is buzzing and i tried everything i could!

2 Upvotes

Brand new Yamaha Pacifica Standard Plus. The low E and A buzz on almost every fret, and you can hear it through the amp. Video: Revstar first, then Pacifica, same attack.

CURRENT SETUP

- Pacifica: relief 0.30–0.35 mm (8th fret), low E action ~2.2 mm (12th fret), 9–46 strings

- Revstar: low E action ~1.8 mm (12th fret), 8s. No buzz.

WHAT I'VE TRIED

- Full restring with fresh strings, neck rested overnight with the truss rod loosened

- Truss rod in both directions: relief from 0.20 to 0.35 mm, measured with feeler gauges at several frets

- Action from 1.4 to 2.6 mm on the low E

- Saddles reset level, then raised individually on the low E and A

- Frets checked with a rocker and a straightedge: none high

- Tap test on every fret (capo 1st, fretted at last fret): all clear

- Coin tap on every fret: no loose frets

- Fret crowns look round under a flashlight

- Saddles, trem springs and loose hardware checked

- Buzz goes away only when I pick very softly

- My Squier Tele (also 25.5") at ~2.0 mm barely buzzes with the same attack

Nothing really changes it. There's no luthier anywhere near where I live, so I'm trying to diagnose this myself. Is this sound normal? What could be causing it?


r/Luthier • • 3h ago

First Panga neck!

Thumbnail
gallery
2 Upvotes

Picked this up the other day. The neck seems a little sticky and the grain near where it got most of the actions seems a bit more rough.

Any recommendations for care?

Normally I high grit sand necks, I feel that’s not the best idea for this one.

Thanks!


r/Luthier • • 4h ago

HELP Wiring Diagram Help

Post image
1 Upvotes

Where does this wire connect?


r/Luthier • • 4h ago

HELP Looking for advice on vintage Yamaha body cracks

Thumbnail
gallery
0 Upvotes

I recently purchased a vintage yamaha 12-string (FG-630) for dirt cheap, with the hope of repairing it for personal use. The one issue that I'm unsure how to fix (and that I couldn't find any good info online) are cracks like the one pictured. The guitar has these micro(?) cracks all around the binding, front, back, and sides.

Is this something that I can shove hide glue (or even CA glue) into and it should be fine? How would I go about fixing this? Is this even repairable? I've started the process of re-hydrating the guitar already, but I have little faith that hydration alone will fix this.

I'm unconcerned with making the guitar look like brand new; I just want to make sure that these cracks won't cause more issues or get worse as time goes on.

Thanks in advance for any help!


r/Luthier • • 4h ago

Bass cut switch?

1 Upvotes

ive also heard this called a strangle switch and ive tried wiring it to a push pull pot following some google images. has anyone found a diagram for this that seems to work well?


r/Luthier • • 6h ago

INFO How to get back into it?

0 Upvotes

Hello everyone. I started building guitars mainly 3 years ago when I took luthiery classes. However nowadays I moved countries and I haven't found any place where I can get back to make the builds I used to do.

What can I do to get back to building without requiring all the big machines and tools a luthier usually has??

What are some resources i can search? I've seen kits and all but they don't convince me yet.

I am open to all recommendations and guidance!


r/Luthier • • 8h ago

Parts help

1 Upvotes

My son was given an Iyv Les Paul guitar by someone I work with.

He had gutted it and gave me all the parts to reassemble.

Today I tried to put the humbucker adjustment screws in and they don’t fit.

The humbuckers are Destiny CNC Wound.

The internet says they should accept a #3 machine screw. The screws I have appeared to be 1” #3 but just in case I went out and bought 4 more. They don’t fit either.

Does anyone know what size they might be and where I can find some? My local hardware stores (Home Depot and Ace) don’t have anything smaller than #3.

I considered using self tapping sheet metal screws but can’t find anything smaller than #6.

Any advice would be greatly appreciated.


r/Luthier • • 9h ago

Failing tuning machine

Post image
0 Upvotes

Hi! I’m looking for advice about a failing enclosed tuner on my Seagull Artist Studio Concert Element guitar.

It’s the low E tuner. When I tighten the button, the back part of the tuner behind the headstock wants to pull away from the headstock. I have to hold it in place to get it up to E.

My Google searches have not produced an answer to what’s going on. Does anyone know if this can be repaired by a novice? Will it require a wholesale replacement of the tuning machine? I’m worried that the other low string tuners might follow suit because they don’t look as snug against the headstock as the high string tuners.

any advice appreciated!


r/Luthier • • 9h ago

I built a free interactive 3D viewer to preview CNC guitar models before cutting

0 Upvotes

I make 3D guitar/bass models for CNC and got tired of not being able to show them off properly, so I built a little WebGL viewer you can spin around in the browser — no download, works on mobile too. Figured this crowd might appreciate it. Happy to answer anything about how the models are set up for machining. (Link in the comments so I don’t trip the self-promo filter.)


r/Luthier • • 9h ago

Guitar stand has tarnished back of guitar - advice?

Thumbnail
gallery
0 Upvotes

My Gretsch Jim Dandy Deltoluxe was sat on a cheap guitar stand recently. There’s a rubber looking portion of the stand that props up against the back of the guitar, and it looks as if it has had a chemical reaction with the matte finish on the back of the guitar.

Is there anything I can do to fix this?


r/Luthier • • 10h ago

HELP Hollow body repair

0 Upvotes

I broke my guitars aux. So my question is basically this:

Would it be more worthwhile to work through the f-holes on the guitar to replace a broken aux (it fell inward) and pickups (I want better ones)..

OR, should I try and cut an access hole in the back, and maybe like order a panel from a similar model of guitar that I can screw back on top. I’m sure this would somehow fuck with the sound of the guitar but I’m not sure how much. I do have access to a general workshop i can do this in.

Guitar is an epiphone casino coupe btw

Thanks in advance for any advice!


r/Luthier • • 10h ago

HELP Killswitch Wiring Question

Post image
0 Upvotes

This is a really basic wiring question, but would this simple example of a killswitch actually mute the signal by sending it to ground or would it only reduce the volume of the output? Is there a more effective way to wire up a basic killswitch/stutter button?

Thank you!


r/Luthier • • 11h ago

Just finished another Explorer

Thumbnail
gallery
13 Upvotes

So this guitar is the first of three instruments, which i am currently building my band mates in Damage Case. This Explorer was built for the lead vocalist and rhythm guitar player Marco and I can't wait for him to check it out.

I used plane wood for the body which I got for dirt cheap around the corner here in Germany. It had been sitting in some shed for 20+ years, is perfectly dry and it's all one piece. Got it for some 15€. While it looks damn cool I can thell you it was an absolute nightmare to work with, and it is also the reason why this is probably the heaviest Explorer I've ever played, seen, touched, built.

Neck and Fretboard are made from Walnut.

Love to hear your thoughts on it!


r/Luthier • • 11h ago

Unsure if I should put bindings on

Thumbnail
gallery
3 Upvotes

just at the stage to try and make sure everything fits. I have not cut binding channels before I am not selling this guitar it is just a gift while I learn and practice the craft.

Do I risk cutting the binding channels and mess it up or do I just finish sanding and cleanup what I have?


r/Luthier • • 11h ago

Can the dings be sealed with clear coat again so that they’re no longer visible and the value might be somewhat restored?

Thumbnail
gallery
0 Upvotes

Hi,

I have a Japanese Fender Telecaster Thinline from the late ’90s here. It’s a really rare piece, especially for left-handed players.

I love it very much, but unfortunately it fell and now has several dings, with some of the finish chipped off. It bothers me a lot, because I’ve probably lost several hundred dollars in value and the guitar is now worth less.

Of course, I don’t buy a guitar because of its value—but it still somehow feels bad. I don’t actually want to sell the guitar because of this, but the dings just really bother me. I’m now thinking about somehow sprucing it up again. Do you have any ideas? Can the dings be sealed with clear coat again so that they’re no longer visible and the value might be somewhat restored?

Or do you have other ideas to make it feel more “lovable” again?

I saw a Telecaster Thinline in another post that survived a house fire and was restored in an incredibly impressive way. Somehow, that’s a little inspiration.

(Link: https://www.reddit.com/r/Leftyguitarists/s/pU7gwkSd6Q)

I’m very grateful for any tips!


r/Luthier • • 12h ago

ACOUSTIC Guitar Leg Rest 2.0

11 Upvotes

r/Luthier • • 13h ago

Your preferred cable connector for strat board to jack?

0 Upvotes

With other guitar types it might be soldering all the way, but for a strat with all electronics on the board plug and play seems to be ideal.

Which connector can you recommend. Preferably with a link to the hardware itself.

Cheers
Tom


r/Luthier • • 13h ago

Is that a scratch or a crack?

Thumbnail
gallery
1 Upvotes

I bought that guitar around 3 moths ago used. I noticed that damage under locking nut several weeks ago and didn’t pay any attention. But I want to know should I worry about it or not. Does it looks like a scratch or a crack? I can feel it with my nail


r/Luthier • • 13h ago

I used Ronsonol to clean fretboard yesterday…

8 Upvotes

I used Ronsonol to clean an Indian laurel fretboard prior to applying Montypresso. I just found out that Ronsonol no longer contains naphtha(!!!)

Have I made a horrible mistake?

The Montypresso is still on the fretboard, so I haven’t seen if the fretboard is ruined yet.


r/Luthier • • 14h ago

Simulation update

3 Upvotes

So I closed the box yesterday! Unfortunately I couldn't match the blueprints 1:1 my skills are just not there yet and I have pretty rudimentary tools. So aside from some material and dimensional changes the first tap test was within 11% of the simulations projections. Which was my expected error. I am going to now make adjustments to the digital twin to account for the material and dimensional changes. If the simulation comes back within 5% . This would be a massive success.

If any of you luthiers want to work with me I would be more than happy to run a simulation of any blueprint you might want to try out. I have pretty powerful hardware to run exceptionally detailed simulations. So if there is a crazy idea you had and wanted to try it out I would love to partner with someone.


r/Luthier • • 17h ago

Mandocello Šefl no.01

Thumbnail
gallery
129 Upvotes

Hi, here is first custom-made mandocello from my workshop 😊

Sound sample: https://youtu.be/4ksMCVm0xVc

www.seflstrings.cz


r/Luthier • • 17h ago

Vegatrem VT1 Block Size - will it fit a 42mm thick guitar body

Post image
0 Upvotes

So I'm considering installing a VT1 into a guitar I'm building. However, There seems to be little to no reliable information on the internet on the exact size of the tremolo block. Has anyone here installed the VT1 in a guitar that is just a little thinner than Standard strats? Does anybody know the block size?


r/Luthier • • 18h ago

HELP Are my tremolo claw screws sticking out too far? (Gotoh 1996T)

Thumbnail
gallery
2 Upvotes

The guitar is currently well set up and the bridge is perfectly balanced, but I'm a bit concerned that the screws might not be sufficiently anchored in the wood.

Is this normal, or are the screws too far out?

Is there a way to get them closer to the wood by tightening them further without causing any issues? I don't mind readjusting the bridge afterward.


r/Luthier • • 19h ago

REPAIR Will I be able to bring this guitar back to life?Let's find out...

Thumbnail
gallery
6 Upvotes

Got this poor thing for 10€...Does anyone here have any info on the brand YOOJIN? Apparently it's from South Korea?