r/Line6Helix • • Jun 12 '25

Meme/Shitpost It is inevitable.

Post image
607 Upvotes

I assume that when Line 6 says the Helix Stadium has absurd amounts of DSP power, they mean "Dragon Shout Projecting" power. Besides, that new dedicated GPU has gotta be for something heavier than just running a GUI.


r/Line6Helix • • May 19 '25

General Questions/Discussion I've made myself a midicontroller so that I can controle the digital amps with some real knobs.

Thumbnail
gallery
437 Upvotes

r/Line6Helix • • Oct 14 '24

Meme/Shitpost It’s funny how much my pedalboard has changed in 10 years

Post image
424 Upvotes

r/Line6Helix • • Jun 11 '25

General Questions/Discussion New products: Helix Stadium and Stadium XL

Post image
415 Upvotes

The Stadium minus the exp. pedal (and at half the size and weight of the Floor), and with touchscreen, is perfection for me. What do you guys think?


r/Line6Helix • • Dec 30 '24 Heart of Silver Mindblown

General Questions/Discussion A Guide to EQ Fundamentals

414 Upvotes

EQ Fundamentals

I see a lot of questions about not being able to make the Helix sit in a mix right, or they can't tame a problem area, or they say the unit just sounds bad. The answer to this is almost always EQ. Understand the fudamentals first and then you can apply them to your own situations.

Guitar Amplifier Fundamentals

In Modern Recording Techniques, David Huber writes that "The fundamentals of the average 22-fret guitar extend from E2 to D6 (82 to 1174 Hz)" with higher frequencies that can reach upwards of this mark and lower in the case of drop and baritone tunings. The frequencies of a guitar speaker will typically be limited at around 5-6 kHz and most speakers start to taper off after this peak. Here is the frequency response of the Celestion V30. This does mean that compared to some instruments, the electric guitar has a lower high end. In part, this is why smaller amps are often used in recording environments; these amps tend to have a frequency spike around 4-5 kHz. This helps to "give it a clean, open sound." (Huber 146)

This is the electric guitar's natural range. If we did nothing else in terms of micing up the guitar amp or doing some EQ work, these frequencies are what we are hearing. This is important to keep in mind because once we start using microphones and EQ, or swapping speakers and cabinets, this is the range we are changing. For example, many dynamic guitar mics, like the Shure SM57, will add a bit of a presence peak in the upper frequency range of the electric guitar. This is a desirable effect in many cases and worth keeping in mind for further sections.

Descriptive Guitar Language

All too often guitar players describe frequencies with words that don't really describe things in an objective way. Here is the general areas we so often try to describe and often mislabel. I would recommend starting to associate these "feelings" or rather vague descriptions with a general frequency band. This can help identify where to start fixing things. You can use a parametric EQ to sweep these problem areas to help.

Frequency BandFrequency Area / Effect / Description
31HzSub-Bass / Rumble / Body Shaking
63HzLow-end / Bottom / Thump
125HzBass / Boom / Boominess
250HzBody / Fullness / Meaty
500HzMidrange / Honk / Boxy
1kHzUpper mids / Snarl / Nasal
2kHzPresence / Crunch / Bite
4kHzHigh mids / Edge / Sharpness
8kHzTreble / Airiness

The Magic Frequencies

Ok, but what does it all mean? In terms of the electric guitar, focusing our attention on some specific frequency ranges is going to help us achieve our tone goals. We will define some EQ goals in the Live and Recording sections. In Bobby Owinski's The Mixing Engineer's Handbook, he identifies the magic frequencies for the electric guitar. Magic frequencies are the ones that we might want to tinker with to "make [the guitar] sound fuller or more distinct." (Owinski 140) You might want to write these down somewhere:

  • Fullness at 240 to 500Hz

  • Presence at 1.5k to 2.5kHz

  • Treble/Air/Sizzle at 8kHz

What you can do with this is make sure that you are getting your mids and presence forward without becoming "honky" or "harsh". This is where the guitar really shines and sounds present. If something seems like it is missing, you should start with these frequency areas. Boosting is best done in a wide Q.

The Electric Guitar's Trouble Frequencies

In addition to the guitar's "magic frequencies", Owinski points out some notable problem areas. Too little or too much of these frequencies can cause your instrument to disappear into the mix, or stick out like a sore thumb. In guitar tone, we often tend to go overkill on the lower frequencies on this list, and due to the harshness of the higher frequencies we tend to use too little. We like to feel the low end and we don’t like to feel an ice pick in the eardrum.

Problem Frequency AreaToo MuchToo Little
200Hz (Mud)Muddy or BoomyThin or Weak
300 to 500Hz (Boxy)Boxy or HonkThin or Weak
800Hz (Tinny)Like a cheap, tinny speakerLacking warmth
1k to 1.5kHz (Nasal)Thin or starting to get HarshMuffled or weak attack
4k to 6kHz (Presence)Thin or HarshDull or Lacking Definition

Preamp Gain Considerations

If you are using a lot of gain you will need to reduce the lows and highs to tighten up the tone and reduce harshness or ear fatigue, respectively. Cleaner tones can benefit from a bit more highs and lows as the clarity here can benefit from a "rounder" sound without getting lost in a mix. This is in part why Fender amps are considered to be excellent clean amps. I am sure most of us have heard guitar players say that they want "Fender clean and Marshall mean" when chasing a specific sound from amps or pedals. This is a hard balance to strike due to the differences in EQ between the two, and tone is often governed by what speaker is in the amp/cab. I really don't like Greenbacks in a clean amp, but they aren't so bad in a crunchy one. We need to try to strike a balance if clean and mean is important to you. Compromises will have to be made.

Putting the fundamentals to use

Obviously, we want to start putting these fundamentals into practice. I would recommend a common, systematic approach to getting your sound into a relatively good starting point. That is really the best that we can do, given there are so many variables from the moment we stop playing in out home and start playing with others (a mix) or outside our regular space (room variables). But first, understand the controls on the amp.

Passive or Active Tone Stack?

I am not going to get into it too much but there are two types of tone stacks on guitar amps, passive and active. Understanding the basics will give you a good starting point.

Passive is mostly seen on older amp designs. They are simple and easy to use and some people say that they sound more "natural", whatever that means. The main thing is passive tone stacks only cut frequencies, they cannot add frequencies. A flat EQ with these is typically Mids on 10, Bass and Treble on 0. Some people like to start here but I like to start with everything on 10 and cut things from there. On these amps it's not uncommon for me to leave the Mids at 10 and significantly cut everything else.

Active is mostly seen on newer amp designs. They can be more complicated and offer more options for shaping your tone. These can both cut and boost frequencies. Most people set everything to 5 and start changings things from there. I would recommend doing the same. In fact, if you are starting out, I would recommend picking a model of a modern amp, with an active tone stack, setting everything to 5 and start by making small tweaks until it sounds good to your ears. Small tweaks are key.

Pay attention to some of the descriptions in the fundamentals section and try to weed out some of the problem areas. Use the mid control, treble and presence (if the amp has it) to push the "magic frequencies" forward a bit. Take care not to get too harsh or honky. Basically get it sounding good as a baseline for further tweaking.

Most tone stacks are interactive, meaning lowering one parameter will affect other parameters. Lowering the bass will change more frequencies than just the bass frequencies. You can see what I mean by looking at the Tone Stack Calculator Online.

Quick EQ Techniques and Principles

  • Learn to use a Parametric EQ and Shelf EQ on YouTube. Just do it and thank me later.

  • Guitar tones that sound good by themselves rarely sound good in a mix, or rather will get lost a bit in the mix and lose definition and clarity.

  • If you want to cut a frequency, do so with a narrow band.

  • If you want to boost a frequency, do so with a wide band. It sounds better to add smaller amounts at a wider range of frequencies.

  • Use a high pass or shelf EQ to roll the bottom end off. Start with 100 and increase the frequency or the cut as needed so you aren't competing with the bass.

  • If you need to identify a problem area, cut or add EQ aggressively and sweep through the frequencies until you find it and then bring the cut or boost down to a usable, natural level. The main thing is we are trying to identify the problem and an aggressive cut or boost will help you. In my opinion, a parametric EQ works the best for this sweep.

  • Using a high pass to cut the bottom end will make the guitar stick out more.

  • Using a low pass to cut off the top end will make it blend with the rhythm more.

  • Using a snapshot to adjust EQ parameters or switch on a parametric EQ is a great way to bring your guitar out front for a solo without increasing the volume too much.

  • A shelf EQ is going to be a great way of taming harsh highs and flubby lows to tighten up your frequency area.

Cabinets vs IRs

I really like IR manufacturers who label them not by microphones used, but by how balanced, dark, or forward the mic mixes are. Ownhammer's RockBox series does this very well. I am a fan of those IRs just for their ease of use. I like a nice balanced cabinet sound and I have been known to use a single IR for over a year (two now). I am back to experimenting now because of some of the amps that have been recently released in the last two Helix updates have me reconsidering my setup.

The Cabs in the Helix are really good but the reality is that they do not give you the same amount or level of tools that IR creators have for mixing and balancing a sound. Yes, you can run split paths and use 4 mics and speakers and blend to your hearts content but it takes up much more DSP and is just a hassle to get that level of detail. I trust my ears and I find that it is easier to get something that works for every amp and preset if I just grab an IR. That is just my opinion. Many people are very happy with those cabinets and it's simple to throw a 57 and 121 on a speaker and call it a day. That is a great, tried and true sound and the Helix Cabs make it easy to do that. I encourage you get something sounding good and set it and forget it.

Playing Environments and EQ Goals

It is worth noting that if you are playing by yourself, you should probably just dial in a tone that sounds good to you and be happy with that. There is no use overthinking things. You can still use the fundamentals to identify some trouble areas so you can fine tune your sound to your liking. This is important to remember because your guitar is the only instrument and so you do not have to share frequencies with any other instrument. If this is the case, widen the frequency range, add some bass, and enjoy how good it sounds. Whether you are playing along to a jam track, practicing, or noodling around: if you can hear yourself and you like the tone, that is all that really matters.

However, if you are jamming, rehearsing, playing a gig, or recording yourself, it will be a good idea to put some thought into establishing some EQ goals. An EQ goal is just determining the frequency area that you guitar is going to occupy and shaping your tone to fit into that particular context. The more instruments taking up precious frequency real estate, the smaller the frequency band is going to be for your guitar. Therefore, as the ensemble grows, the more restrictive and careful we must be with EQing our sound.

Live Environment

Ensembles vary in size and volume, some gigs have a soundcheck and some do not, some gigs don't have a dedicated or experienced sound person, and sometimes the playback system isn't all that great. There is no silver bullet. The best advice that can be given here is to keep it as simple as possible by eliminating variables, ensuring that the volume isn't going to create issues, and making sure that you are communicating EQ goals with your bandmates or soundperson to achieve the common goal of everybody sounding good and avoiding volume wars.

The most difficult thing in a Live Environment is that you don't get many opportunities to slow down, listen from where the audience is, and carefully mixing and EQing individual instruments like we can in a studio environment. You just have to go with it and try to get things right on the fly.

Eliminating variables

In my opinion, this is the most important part of the section because it is going to eliminate some common issues that have everything to do with EQ, but not in the way you might think. It is by eliminating those sneaky issues that can and will arise when we have too many options.

  1. IRs and Cabinets: These have a major effect on how your instrument sits in a mix. The bigger and louder the playback system is, the more noticeable the change is going to be when you move from one cabinet to another with snapshots or changing presets for a song. Before digital modellers, we would roll up to a gig with our amp and cab and the soundperson would throw a SM57 in front of it. Done. Now imagine the pain the soundperson would have if every song you changed the mic position, mic type, the cabinet, and the speakers. I see this mistake all the time and it is jarring as an audience member and hard on the soundperson and your band. One song the guitar is perfect, the next you can't hear it, then it's too loud. Just pick an IR or Cab and leave it alone for the entire show. I don't care if you want your Fender amp model to be more "authentic sounding" and you want to use a Jensen IR and you also want to do the same for your Marshall amp model because Hendrix played one. What is more authentic is sticking it out with a single cab for an entire show and not ruining everybody's nice time.

  2. Amps: If you want to be a nice person, the above rant can also apply to amp models as well. The caveat being we can change amps for gain structures, but we should keep the EQ similar. Now, I think you can have your clean amp a bit rounder and your crunch amp a bit tighter but just put some thought towards it and be mindful that you are introducing a variable and be open to the soundperson’s advice. Yes, your clean tone might have to be a bit thinner than you would like it, but at least it is being heard and not competing with the bass.

  3. Presets: For any given gig, I typically stick to between 1-3 presets. This might vary if we throw a few covers into our set and I want some specific weird thing for a lead line. For example, the DOD440 envelop filter Johnny Greenwood uses on OK Computer or a phaser on "Machine Gun" by Slowdive. The things I use 80% of the time will live on just 1-2 presets. These presets all have the same amp/cab combo. I’m not saying don’t run a dual amp/cab rig with fun split paths and creative EQ. I’m saying if you do that, stick with it for a show and you will have a lot better results.

  4. Guitars: Hot take here, but in the spirit of trying to minimize variables, using guitars with different pickups and output levels is going to add a variable. I know we like bringing our whole collection of guitars like we are Mike Campbell, but professionals also have professional guitar techs and soundpeople that intimately understand the professional guitar players sound and how to make it work. For those of us who do not have these resources, it is best to reserve other guitars for tunings that are going to ruin your main guitars intonation or take too long to do in the middle of a set. You don't really need a "Drop-D" guitar, you probably do need a "Drop-C or Drop B" guitar and it should, at the very least have a similar output level, or at least be conscious of how these tunings affect the entire band's mix. I know 7-strings are popular now and you can easily switch between guitars without screwing your band mix up, but your should put some effort into it, and if you don't, don't be surprised if the hacky soundperson lets the song turn into a mushy blob of mud. That would be your fault, not theirs. I am not going to go up to Kevin Shields and tell him to stop using all those different tunings, but then again, MBV is known for being extremely loud and driving the audience out of the building so YMMV. This is a good example of how different tools can be a boon in the studio but might detract from consistency in a live show.

In general, it's about not doing different things all the time that are going to give you and everybody else a harder time than is necessary. As mentioned earlier, guitars that sound good by themselves rarely sound good in a mix so once you get an amp figured out with your group, you should probably stick to that general EQ. If you had to cut the bass way more than you thought you would have too, if you are going to use other amps, you would be wise in doing the same thing with those amps. You can see how this makes things easier if you just stick to 1-2 amp options and a single cab/IR. If you have the support that can make multiple variables work, go for it, but if you have gotten this far, it is unlikely that is the case.

Fletcher Munson

When the volume goes up, it changes the way we perceive midrange frequencies. There are a lot of good articles and videos on this so I won't dive into it much. The most important thing, is that if your tone in a live environment is important to you, you should dial it in at, or as close to gig volume as you can. This includes making small last minute changes during soundcheck. Ideally using the Global Settings so it applies to all your presets.

Listen to the rest of the band

Rehearsal is a great time to listen to the rest of the band. If your guitar is boomy and clashing with the bass, use a high pass filter to fix it. If you get to high volumes and your tone is honking like a goose, bring the mids back a notch or sweep the frequencies with a parametric EQ to cut back the offending frequency. Save the preset! Remember, you have lots of banks and saving these changes can save you time and energy during gigs because you have already figured it out. Talk to your group, especially other guitar players and bass players because it is easy to compete in similar frequency ranges.

Studio Environment

When recording, things get a bit easier becuase we can slow down and take our time. We have access to EQ graphs, all the tracks/instruments, panning, and more. There are lots of tools we can use when we are not the ones on stage playing the guitar. Most of the same principles apply but this is where we can really get creative with different amps and cabinets and guitars and effects and of course EQ!

We are not plagued by Fletcher Munson, no soundcheck, volume wars, and reflective rooms. It is a nice zen zone where we can lay down some tracks and use the EQ fundamentals to get a great sound. The EQ Goal here should be carving out a place for your guitar tracks, using different gear to create some distinct layers, and generally just have fun with it. Practice makes perfect and the more you record, the more you will begin to learn what works well in specific contexts. Once again, guitars that sound good solo, probably won't work in a mix very well. Use a shelf EQ to bring the extremes tighter as the layers begin to build. Look at the available tools in your DAW, and watch videos to see how skilled mix engineers are doing things.

DAW Tools

You can also run your Helix into a DAW if you have one and check out a graphic EQ to see what is going on. This is a nice visual that can help you identify some problem areas or areas where you sound can be improved. You can see how turning the knobs on the amp model will affect the end result and how changing IRs or Cabs and Mics will affect the sound. It is nice to have a visual. I would recommend using your ears if you are playing in a band and if you are lucky, you will have a soundperson to help you out further.

A Final Consideration

The final thing to consider is that musicians and sound engineers have been keeping things simple for decades. Guitar amps are designed to sit in the right place in a mix. This is especially true with modern amps that have benefitted from the availability of modern technology. But things can be over done and EQ can be overdone. I would recommend using small changes to achieve your goals. Huge cuts and boosts should be used only to identify areas for improvement and then they should be tamed back so things sound more natural. Remember, the gear is designed to sit in the right place! The 57 and 121 combo is a staple for a reason! V30s are popular among metal players for a reason and Fender's are popular for cleaner tones for a reason. Rules are meant to be broken but with some knowledge of some fundamentals we can start to more intelligently approach our tone to make playing with a great tone easier and more enjoyable.

Do You Want More?

Please feel free to contribute some knowledge on the topic and please let me know if you like the post and want more modeller related educational content in written form. If so, what do you want to see next?

Please also see A Guide to EQ Fundamentals: Part 2 for more.


r/Line6Helix • • Nov 07 '25

General Questions/Discussion Some dude in the Facebook group got his stadium early

Post image
390 Upvotes

They're all freaking out naturally lol


r/Line6Helix • • May 15 '25

General Questions/Discussion My Helix Effects Pedalboard

Thumbnail
gallery
389 Upvotes

Thought I'd share how I made a pedal case for my Helix.

The case is an old typewriter suitcase and the FX is screwed to the case using the original threads.

The lid is detachable but I like to keep it on because I keep my Setlist in there (invisible for the audience 😉). There's a 3d printed Skadis pegboard inside with the Skadis rubber bands to hold cables and stuff. I recently switched from cable to a Boss WL60 wireless system and I just tuck the receiver under one of the rubber bands (amazingly the lid still closes).

On the right is an expression knob that I use as a master volume control.

Strong door magnets keep the board of the second floor in place, underneath is a pedal power supply that also powers the Helix with a current tripler. I use the external tuner's DC out to power a LED light strip in the lid.

Maybe this is a good inspiration :)


r/Line6Helix • • Sep 14 '23

Meme/Shitpost Since HX edit isn’t on ios

Post image
380 Upvotes

Lol


r/Line6Helix • • Sep 23 '25

Meme/Shitpost What a rip off!

Post image
377 Upvotes

Of my time lol. Ever since I got this thing I have not left this area. It is so fun building presets. It’s like being in a Guitar store and trying out everything when it comes to amps and pedals. If you’re a lurker here like I was don’t be. Go get a helix if you can. This has literally changed everything for me.


r/Line6Helix • • Oct 21 '25 Bravo

Tone/Feature Demo My POV from a gig

367 Upvotes

just showing my love for this amazing processor


r/Line6Helix • • Sep 27 '25

General Questions/Discussion So, I played Stadium XL

Thumbnail
gallery
367 Upvotes

I am currently at Guitar Summit in Germany and I was able to try Stadium XL.

Not sure what you guys want to know but a few observations:

  1. It is smaller than Helix but still quite large

  2. I love the fact they left the buttons from Helix Floor - this hybrid touch/button control is just great and familiar for previous Helix users

  3. There's new amp models for every genre now. I can't remember and didn't take photos of all of them but I am an advocate for "less is more", so even in the current stage I'd easily find the sound I want

  4. Of course it sounded great through headphones, but I would really need to try them, old vs new, side by side to tell a difference. But everything was there that matters: dynamics were really good, I played mostly plexi and 800 marshall models and they were great, raspy, clear, joy to play

You can guess that trying a piece of gear at an expo, with people queuing behind you is far from comfortable experience.

Anyway, it's real and alive, it's here, they gave it to the public to try so it's stable enough, the sounds are solid as much as one can tell, the controls are great.


r/Line6Helix • • Oct 23 '25

General Questions/Discussion Our 2026 gig setup

Post image
327 Upvotes

Hello! Just wanted to quickly show our new rig setup. 3 helix units, 2 controlled by the normal controller and i control mine with a RJM Mastermind GT22. Wireless SLXD series for 4 wireless mics and 3 wireless Guitars. Sennheiser G4 IEMs controlled by the Wing.

Edit for the ones curious the signal path: For our bassist and one guitarist it's just wireless into the Helix and one CAT cable to the pedalboard.

My Signal Chain is: 2 different guitars: A gibson les paul wireless into the Mike Hill 4 input switcher. An Epiphone ES335 with a Fishman Piëzo bridge running a stereo cable to the rack.

Stereo cable goes into the Voodoolab GCX that does the AMP switching. The magnetic pups go to the Mike Hill 4 input switcher. The piezo bridge is running into a Fishman Aura Spectrum DI for acoustic

From the input switcher it goes to a Digitech Whammy DT (in the drawer) and from there it goes to my pedalboard with a tuner and a Talkbox. From my Pedalboard it goes back and in to my Helix.

The Helix, Voodoolab GCX and the Digitech Whammy DT are MIDI controlled. I use the Whammy DT for drop tunings. As a medleyband i don't have time to switch guitars for just one minute of a song.

All controlled by the RJM Mastermind GT22 (Best piece of kit i've ever owned and Ron is a legend)

EDIT 2: For anyone interested in my band; we are from the Netherlands and are called Zit 'R Dik In. We make medleys and play every song you would want to hear on a festival. If you want to see our promo it is here :) https://www.youtube.com/watch?v=mhDzpg-kxrA


r/Line6Helix • • Jan 04 '25 Helpful

General Questions/Discussion A Helix User's Guide to Helix Cabs and Impulse Responses

326 Upvotes

Last week I made a post aiming to help users EQ their Helix a little bit better and followed it up with a second part. After that, I had a few people ask for information on IRs and Cabs which happens to be something that I am particularly interested in, as well as being one of the elements of our current generation of modelling devices that took a big leap forward over the prior generation. In addition to this, there are a lot of misconceptions floating around out there with respect to IRs and Cabs. Very little is written about IRs themselves, at least in published work. Most of the really good information is either in books written by engineers on the real, analog gear, or learned through studio time and/or stage time. Even in live venues, I don't know how many times I have seen a guitar player hanging a SM57 in front of a cabinet, and touching the grille cloth (don't do this). The aim of this post is to provide some brief explanations about the differences between third-party IRs and Cab blocks, discuss some standards for miking guitar and bass cabinets, give beginners some information on popular speakers for those looking to get started, and at the end I will give you my unhinged opinion on third-party IRs.

What is an impulse response?

When we are speaking about guitar cabinet impulse responses (IRs), we are referring to a digital representation or a capture of the unique properties and characteristics of a cabinet and the speaker(s) inside of it. These characteristics are captured by playing a sine sweep or white noise through the cabinet, and recording it through a microphone(s). Then the recording is processed through a plugin that will analyze the sound and generate an IR file. This is usually much better than using DSP algorithms to generate "cab sims". At least, most people are in agreement that they perform better.

Additionally, because IRs are recorded using microphones, it is not just the characteristics of the guitar cabinet and speakers that make up the character of the IR. This means the microphone itself, the placement, and the room ambience are also recorded. This is why there is no "amp-in-the-room" cabinet or speaker; a question asked in modeller forums every hour it seems. You can all stop asking now.

Furthermore, the nature of recording IRs means that creators can make mixes of different microphones or different speakers in the cabinet. This also means that there are a variety of different variables that are introduced when creating these captures. Third-party IRs that are not included in the Helix lineup are created by engineers that have their own opinions of what sounds good or what would be useful in a mix.

What can and can’t IRs do?

Often IRs are given a definition of being a replica of a speaker and cabinet as well as the characteristics of the microphone that captured them. While this mostly true, there are also limitations. We have a basic idea of what IRs are, so before going further down the rabbit hole, we will develop an understanding of what they actually do, and what they do not.

Impulse responses capture:

  • the frequency response of the speaker and the effect of the cabinet on the speaker

  • the effect of the microphone type and position on the frequency response

  • the phase response of how frequencies align or shift

  • room reflections if captured

Impulse responses do not capture dynamic or linear behaviours such as:

  • speaker breakup

  • cone movement

  • dynamic compression

  • feedback or resonance

Essentially, this will give us a very usable static profile of the frequency response of the speaker, cabinet, and microphone used. Static is the keyword here. IRs do not provide the dynamic behaviors of speakers and cabinets. Some of these behaviours can be modelled, but the IR itself does not provide this data. One of the most important things to note is that it effectively means that the wattage of the speaker doesn't matter in the sense that using a low efficiency speaker IR isn't going to give us speaker breakup, and cranking our Amp model isn't going to blow up our IR and likewise isn't going to give us dynamic speaker distortion or compression like we would see with analog gear. In terms of sound, I think they do their job very well and Amp modelling like we see in the Helix gets us some good dynamics anyway. On a recording, I can't really tell the difference and neither can you.

Helix Cabs

The current lineup of Helix cabinets introduced in update 3.50 are a collection of "Thousands of impulses...captured with Sound Design's all new IR capture system and consolidated into 20 guitar cabs and 4 bass cabs" (Helix Update 3.5 Release Notes). Basically they are impulse responses with a fancy interface. Since the 3.50 update, Line 6 has continued to add more cabinets/speakers. Thank you, Line 6!

The way that these work in the Helix is we load in a Cab block, select a microphone, and move the microphone around, and we can change the axis to 0 or 45 degrees off-axis. This essentially selects the IR that corresponds to your parameters. If you have some knowledge of how microphone placement affects the sound of your guitar amp, you will find this very easy to use. You can also change the output via level and the Cab block includes a high and low cut for EQ.

If you load up a Dual Cab block, you can choose different cabs, microphones, positions, low and high cuts, levels, angles, and get new parameters to pan the signal and add a delay. This gives the user a good variety of tonal options. Probably much more than what most people even need. The big pro with this system is that if you are knowledgeable about how to get the sounds you want with a microphone, you can really dial in your sound as optimally as you can, before hitting record or getting on stage.

The con, of course, is that not all of us are engineers and know how to take advantage of these powerful features. The other con is that IR creators are not necessarily restricted to the same parameters that Line 6 gives us. For example, if an engineer wants to set a microphone at a 25 degree off-axis angle instead of a fixed 0 or 45, they can do that. If they want to use a microphone or speaker that Line 6 doesn't have, they can do that. Or if they want to capture the room ambience or the back of a cab, they can do that. Before getting too carried away here, I want to say that Line 6 did a great job and I love the new system and IRs that they captured. They really ticked all the major boxes and gave users really everything they would ever require as far as microphones and Cabs goes.

The Pros and Cons of Third-Party IRs and Helix Cabs

Third-Party Impulse Responses (IRs)

Pros:

In a nutshell, the pros of IRs come in the form of more advanced mixing of microphone recordings and being able to lean on the experience of a trained ear who knows what to look for. In addition, third-parties are not limited to the cabs, speakers, mics, and parameters that Line 6 has chosen. If you want a very particular speaker and cab combination, you can probably find it captured by a third-party. Third-parties can also use several mics at a time and capture some room ambience or the back of an open back cab. These are not really options we have in the Helix Cabs. You can use two dual Cab blocks for a total of four mics to mix in but you have to use parallel paths and it consumes a lot more DSP than just a single IR block with all the goodness baked in. That said, I am fairly confident that most IRs are close-miked and most creators aren't going out of their way to add a ton of room ambience and the like when not everybody is going to want that. That said, some do this and it can sound great.

However, the biggest pro in my opinion is that some IR creators take the time to make purpose-built mixes. For example, Ownhammer's RockBox IR packs are separated into three cabinets per speaker pack, from tight to scooped. Then, each cab is broken down into five options for how bright or dark the mic placements are. Additionally, the "classic" cabinet is further divided into five options for mic mixes, ranging from tight and forward to dark and thick sounding. This makes it incredibly easy to pick a cabinet that is going to work for you and flip through a couple of options and then know exactly where to go for what you are looking for. It is an easy way to get a good sound without having to fuss with microphone placements.

Cons:

To start, most IR creators don't do a good job at organizing their IRs in a manner that is intuitive and conducive to a steamlined user experience. While they may have some great captures in there, it kind of forces you to check them all out to see what they all do. Finally, they cost money and we do have a great solution already baked into the Helix. I want to say for free, but we did buy the unit.

Helix Cabs

Pros:

They are easy to use and are included right inside of the Helix. New additions come at no extra cost, just like everything else in the Helix updates. Thanks again, Line 6! There is a good selection of speakers and cabinets at this point and they have Cabs(IRs) recorded with the most commonly used studio microphones, cabinets, and speakers.

Cons:

The biggest con is that you need to know how to use microphones and it takes time, a conscious effort into learning, and a bit of trial and error to learn:

  • how to blend microphones in a pleasing way

  • what the individual microphones sound like

  • what frequencies the microphones are "boosting" and attenuating

  • some common guitar cabinet miking techniques

  • and of course more can go wrong when we (amateur recording engineers) are in control

The other con is that we don't have the flexibility that engineers have due to the limitations of the Helix Cab block parameters. This does mean that it is possible, if not likely, that a third-party IR mix, created by a savvy engineer, could sound better than one dialed in with limited parameters by an amateur. However, better is subjective. What are we talking about here? 20% better? 5%? 1%? It is really up to who is listening to it and engineers have been recording fantastic records with an SM57 on guitar cabinets for decades. We do have the ability to do this with Helix Cabs.

Are the Helix Cabs good enough?

This begs the question: "how many choices do we really need?" If you dive into some books written by recording engineers, there are standard ways of doing things and after years of practice and refinement, the standard have emerged because they are the most optimal way(s) of capturing a cabinet via microphone. We see these standard methods all the time and they are surprisingly simple if you know some basic fundamentals. I am willing to bet that the majority of good third-party IRs are recorded very simply with standard microphones and placements; placements that can easily be replicated in the Helix.

However, I must concede that in some cases we will never know precisely how great IR mixes were made and if there is some special sauce in there. I know some room ambience or a mic on the back of an open back cab does add a little something extra that we just can't get in the Helix. It would be wrong not to acknowledge this fact, as subjective as it may be. All that said, the new Helix cabs are most definitely good enough and come with the flexibility of moving mics around yourself without going through 1,000 IR captures which can be an arduous process. Plus, they are "free".

How to Mic a Guitar Cabinet

If you have been holding your breath for this section you can finally exhale. However, I want to first acknowledge that there are many mics and cabinets/speakers in the Helix and I will not be covering them all or even the majority. In other words, this isn’t an informational collection of frequency responses for all this gear, nor is it a guide to every miking technique. If you are hoping for this sort of information, I recommend picking up a book on the subject and/or searching online for some frequency response charts to fine tune things.

Additionally, It is worth noting that "the player and the instrument contribute about 50 percent to the overall sound...the room contributes about 20 percent...the mic position contributes about 20 percent...the mic choice contributes about 10 percent" (Owinski). Room isn’t something we can capture all that well here so make of that what you will.

Establishing Goals

The first thing we need to figure out is what we are trying to accomplish. If we have no idea what we are actually trying to do, then we are just moving sliders around haphazardly, hoping for something good to happen. At the most basic level, we are trying to get our guitar to sound good while getting the EQ as close as we can to sit perfectly in a mix. It’s a tall order that usually needs some additional EQ. You can take a look at my posts on EQ for more info on this.

If you are playing by yourself at home with no intention of recording or playing in a group, you might want to just use the default settings on the Helix Cabs to identify a speaker you like and go buy an IR pack for that speaker and find a mix you really like. It might be worth the $10-20 price tag for your time and possibly sanity. Otherwise, read on and keep a goal in mind if you are trying to fit your guitar into a live mix or a recording.

Microphone Fundamentals

The 80/20 Rule

I am sure that most are familiar with the Pareto principle or the 80/20 rule. 20% of the gear out there is likely to be used 80% of the time. This applies to pretty much anything and so the focus is going to be taking a look at some of the most popular microphones and techniques that you are going to end up being used in the majority of cases. What we are focusing on are standards.

Moving things around

Remember, you should set up a loop before the Amp and Cab blocks and play your guitar a little bit. Play heavy and light chords, some single notes, and some arpeggiated chords. Let the loop run while you are changing things around. One way to set up a microphone is to open HX Edit (it's easier) and listen to the loop while moving a microphone around until it sounds good. If it sounds good, it probably is good. That said, the modern standards coming up are probably going to be optimal and the best thing to do 80% of the time. At the very least, they can provide some guidance on how moving the microphone affects the sound and give you a solid starting point.

The basics on how moving a microphone affects the sound

For now, we will assume a starting point of the cap edge (edge of voice coil cap).

  1. Moving a microphone further away from the speaker cap (away from the cabinet) will attenuate (reduce) both high-frequencies and low-frequencies. Move it too far and you will lose definition. You will also get a bit more room sound and ambient sound. The closer you get to the speaker, a proximity effect occurs creating an increased low-frequency response which can make some microphones unsuitable for close-miking.

  2. Moving a microphone towards the edge of the speaker attenuates high-mids and highs. Once again, too far and things can lose definition in the high-mids and highs but can attenuate some lows and low-mids. For some tones, the cap edge is too bright so you have to strike a balance with a single microphone or add a second to blend.

  3. Placing a microphone off-axis (in our case 45 degrees) can attenuate high frequencies. If the angle is too great, it make the sound lack definition and feel muted. Really it depends on the microphone. Once again, it might be good to blend.

How to Mic a Guitar Cabinet

Miking a cabinet starts with choosing the right gear for the job. This includes the speaker and cabinet. We will cover some widely used selections and what they are good at. Further research is up to you if you want more information. For now, this should cover the vast majority of use cases.

Choosing the Right Speaker and Cabinet

In Tone Manual by Dave Hunter, he makes the observation that "the speaker is the first constituent that actually puts your tone back into the air". Therefore, it is extremely important to choose the right speaker. Guitar players change so many things in pursuit for great tone, when all they might need to do is replace a worn out speaker or try a totally new one. In the digital world, this couldn’t be easier!

It is always good to try to get things right at the source before we start thinking about EQ and we want to choose a speaker that is going to work well with our Amp and sit well in our mix. Below are recommendations on where to start, based on some of the most commonly used speakers.

Speakers

We are using the Pareto principle again. What handful of speakers are used the overwhelming majority of the time? More importantly, why are they used so often. If we answer this, we can apply the correct speaker to our own individual style and obtain the knowledge to apply to other potential speaker options. No sense looking at exotic options unless you know why a particular speaker does or does not work for you. Make sure to take a look at the frequency response graphs to see how the speaker will affect the sound...if ya nerdy.

The Celestion V30

Most likely no surprise here. Taking a look at the Helix Cabs as of 3.80 there are six cabinets housing V30s. This speaker has dominated modern hard rock, metal, and alternative rock. It is found in a ton of 4x12 cabinets and 2x12 cabinets. Popular in studios and on stages. When I think of a modern, tight metal tone, this is the speaker. I find this speaker surprisingly versatile and it is not just a metal speaker. If you don’t know what you want, this would be my recommendation.

Characteristics:

  • tight low end

  • strong midrange

  • smooth highs

  • sits really well in a mix

  • can be overly bright and aggressive

Celestion Greenback and Variants

There are already few of these in the Helix making it quite a popular speaker in the unit itself. In fact, many speakers like the Creambacks are based on the original Greenbacks but with different power handling and slightly different frequency responses, so if you include all those as well it might be the most popular speaker in the Helix Cabs. This speaker is the quintessential vintage British speaker tone. It is a very responsive speaker and should be the go to for most classic rock and blues. Despite the quirks or "character" of low powered speakers they are a huge part of "the rock'n'roll and blues sound" (Hunter). The speakers have also inspired a lot of “boutique” options like those made by Scumback and the likes.

Characteristics:

  • warm and loose low end

  • smooth midrange

  • very dynamic

  • breaks up at lower volumes

  • has a nice grittiness to it

  • sounds vintage

Celestion G12T-75

The Helix has three options for these speakers. This speaker was sold in the Marshall 1960 cabs in the 80s and 90s. It wasn’t all that expensive and it saw widespread use during that time. It was often used in higher gain metal and hard rock. It is a great hard rock and metal speaker. It would pair well with another player using a V30 for sitting into a band mix. This is a great choice for a bit more scooped hard rock and metal tone. Despite having a slight mid scoop, it has bright highs that can make it good for lead lines as well as heavy rhythm.

Characteristics:

  • tight low end response

  • scooped mids

  • bright highs and sizzle

  • great at handling high gain

Jensen C12N

The Fender speaker. The quintessential American speaker sound. Of course, many variants of this were sold in 10”. It’s a fantastic speaker for clean Fender tones. A perfect choice for those playing lower gain genres such as country, jazz, blues, and cleaner indie rock. Fender amps are also popular as pedal platforms in genres like more modern shoegaze so this might be a good choice for those playing heavier genres as well. But don’t expect a tight focused low end out of this speaker, it might flap around like sleeve of wizard.

Characteristics:

  • Clear, bright and bell like

  • Fairly balanced frequency response (flat)

  • Nice round lows

  • More scooped than a typical British speaker, including the G12T-75

  • A perfect speaker for clean tones

A note on speakers

I could talk about speakers all day long. They are often overlooked, but tone is in the cone and nothing will drastically change your tone like changing a speaker.

Choose your speaker wisely and if you start looking at some of the other speakers out there they are often based on the above speakers with tweaks to power handling (which doesn't matter for IRs) and frequency responses (does matter for IRs). My suggestion is that you pick a speaker from above based on your genre(s) of choice and get to know that one speaker very intimately. Learn its strengths and weaknesses and develop your ear. Identify if and where it needs improvement and learn to EQ it through microphone placement and EQ blocks. Once you have a handle on it you could look at some IRs of more “boutique” speakers that solve any potential issues you might have in the frequency range. Or try out some more of the many Cab options in the Helix. Remember, these speakers are classics for a reason.

Cabinets

Originally, when I was writing this post I wanted to skip this almost entirely. But the more I thought about it, the less I wanted to take the easy route because the type of cabinet really does matter. There are just so many different materials, brands, dimensions, standard or oversized, open-back, closed-back, angled, straight, etc. However, I am going to keep it very basic for those who are interested or learning about this for the first time. The most important thing here is that the cabinet type does have big effect and you might want to pay attention to it.

Cabinet TypeSound CharacteristicsHigh-End ResponseMid-Range ResponseBass Response
1x12Balanced, focused toneGoodClear and definedModerate
2x12Fuller sound with more bodyGoodWarm and presentBetter
4x12Powerful, thick soundModerateStrong and punchyGreat
Open BackAiry, spacious soundExcellentSmooth and openModerate
Closed BackTight, focused soundGoodPunchy and tightExcellent
OversizedEnhanced low-end and resonanceModerateBalancedExcellent

Choosing the Right Microphone

I know we don't all play metal. In fact, I wouldn't consider myself to be somebody who plays metal, at least not in the traditional sense. However, I do play quite a bit of heavier music with a good amount of distortion so I tend to listen to advice from metal producers as they know the intricacies of recording and mixing distorted and overdriven tones better than anybody. Mark Mynett notes in Metal Music Manual that when you are "recording heavy guitar sounds, the simplest mic selection and placement approaches are frequently the most effective." For good reason, the microphone that he delves into is the Shure SM57. Notably, the SM57 has a sub-200Hz roll off that works well with close-miking. It also attenuates the muddier frequencies and has prominent high-mids. This is perfect for heavy rhythm playing and "many contemporary rhythm sounds have been captured" by close-miking with a single SM57 (Mynett). In fact, it is just plain good for giving a guitar cabinet more of what we want, and less of what we don't.

Furthermore, we see SM57s on stage all the time because close-miking is preferred in that setting, they are durable, and relatively inexpensive. Don’t like the price fool you, they are fantastic microphones that punch well above their weight class.

The Sennheiser MD421 (421 Dynamic) is also excellent and often used alongside a SM57 to capture some more low end. Its low end roll off is around 90Hz so it’s a bit darker and close-miking with it will result in a more pronounced proximity effect.

The Royer M121 (121 Ribbon) is often used along with a SM57 to "suppress the fizzy qualities of a high-gain sound" and add some warmth to your tone (Myett). Owsinski also recommends this microphone to add body to your sound. I like this pulled back a bit because of their low frequency response. A fantastic microphone and often paired with the SM57.

If you cannot make a SM57 or a combination of the SM57 and either a 421 or 121 work, there is something else wrong. Either the player, the cabinet, the positioning, or something else in the signal chain like the Amp model is dialed in too dark or bright or some premature EQ work.

Techniques for Miking a Guitar Cabinet

The Modern Method

The tried and true modern method is a SM57 about an inch away from the speaker. The SM57 is placed about 3/4 of the way towards the edge of the speaker away from the cap edge. On the Helix this is a value of around 5.7 (10 = edge, 2.4 = cap edge, difference = 7.6 x 3/4 = 5.7). Move it towards the cap for a brighter tone and towards the edge for a darker tone. This is set in a nice balance between the cap and edge, giving you a bit of everything. Outside of heavy genres that place a premium on presence frequencies, this is a good place to start.

Owsinski notes two variations of this method. First, add a Royer R121 "right next to the SM57" or in our digital world, we can just put it at the same value on our second speaker. Then adjust them to taste. The 121 will be darker and provide more "body". Second, instead of a 121, add a 421 Dynamic to the right of the SM57 and set it at a 45 degree. This one can provide a lot of different sounds by changing the levels of the two mics. The SM57 gives you the bright tone and the 421 gives you some extra midrange and low-end. The off-axis will cut some brightness from that microphone. Feel free to move them around.

SM57 Half on / Half off Method (the cap edge)

In this method we instead begin with the SM57 close-miked on the cap edge to start with the brightest tone. If you put it straight on the cap, the microphone will pick up some noise from inside of the voice coil, so it is better to start on the cap edge and start working away from the speaker or towards the edge of the speaker. This will give us a variety of tones that are darker than what we are starting with, Depending on the combination of away from the cap and/or towards the speaker edge, we will see differences in how the highs and lows are attenuated which will shape the midrange differently. If you want some awesome charts buy Mynett's book.

Like before, you can combine the SM57 with a 421 Dynamic (on axis or off) or 121 Ribbon for more body. You can also combine it with another 57 Dynamic in another position or a 57 Dynamic off-axis. Feel free to move them around.

Similarities

Essentially, both methods have more in common than they have in difference. Both standards are close-miking using a SM57 and acknowledge that you can supplement the sound by adding another microphone to balance the tone with some darker characteristics. It all depends on where you want to start. Typically, I prefer to start at an extreme and go from there. Therefore, I like Mynett’s method of keeping things simple and trying to get it right with the SM57 near the cap edge. It’s a great place to start with most Cabs. You know that if things are too bright you can move it back a bit and keeping it close to the cap edge gives you the most upper midrange presence frequencies for heavier music. The 57, 421 and 121 really are the 20% that are used 80% of the time…or more!

Other microphones and basic troubleshooting

I will reiterate that there are a lot of microphones out there that can be used for a variety of different sounds. If these three microphones aren’t doing it for you, try to figure out what frequency you are hearing, or not hearing by doing an EQ sweep with a big boost or cut. Once you found the frequency, try to get rid of it with position or blending. If that doesn’t work, try researching a microphone that attenuates those frequencies naturally and try using that instead. Or look for a different cabinet or speaker that naturally attenuates those frequencies. However, I cannot think of a better place to start than the tried and true close-miked SM57. Plus, the issue is more likely something else in the chain, the placement, or the player.

Techniques for Miking a Bass Cabinet

The Standard

Use a large-diaphragm dynamic such as the 112 Dynamic or the 52 Dynamic placed on the cap edge or a bit more towards the edge of the speaker and 2-3 inches away. If this is too bright, it is better to move the microphone back a bit more instead of towards the speaker edge, especially if you are using a smaller 10” speaker.

A variation is pairing your mic with a SM57 at the same location, just to the right (so a few values more towards the edge of the speaker). This will add a lot more brightness but if that is something that you want, this will give you it. If you start moving the 57 towards the cap things will probably get too bright. If you play fast or heavy music and your mix calls for it, it might make sense to attenuate some lows so a 421 Dynamic instead of a 112 or 52 Dynamic is an excellent option for a tighter low end to clean up fast playing.

This is essentially the standard for miking a bass cabinet. It is a bit more basic because it’s not as important to get brightness or attenuate lows as it is with a guitar cabinet.

Blending in DI

Both Mynett and Owsinski recommend mixing the miked signal with a DI signal if that sound fits what you are going for. You can get a lot of tonal options by blending a “DI” signal and our "amp" signal. Essentially, it’s a good idea to at least think about blending in a DI signal with your Amp and Cab blocks. Personally, I like to do this, blending a clean Bass DI with a SVT or replacing the clean DI with the Obsidian 7000 for some dirt. It gives you some more flexibility without using another microphone. Full disclosure, I am only referring to my own experience recording bass here; I don’t play bass live. I primarily play bass and usually I see SVT rigs or DI rigs so that’s what I use as an Amp/Cab and if you don’t know what you want, that’s a good starting place. Usually most third-party IRs will have an option for an SVT Cabinet.

Choosing an Impulse Response

Finally, after diving into quite a few topics we come to the final section. This is meant for those interested in buying some IRs to try out. Hopefully you have had the opportunity to explore a few of the Cabs options in the Helix, played around with the microphones, and have come to a conclusion of what speakers you like and work well for your situation. A final pro with IRs is if you buy a nice curated pack instead of 1000 IR files, it does limit your options and sometimes limitations can be incredibly freeing when it comes to using gear with seemingly limitless options. If you feel this way, IRs might be exactly what you need to let go of the 1000s of combinations of microphone positions, microphone options, blends, cabinets, and speakers that are currently contributing to your analysis paralysis and overwhelm. You might not be able to buy back your waning sanity, but for everything else there's...

Frankly, I am hesitant to recommend any particular IR company. I do not have a lot of experience with many different creators and so I know whatever I say here is not going to be objective. All too often I see people parrot remarks about how “this IR creator is the best” and these remarks seem to be based on very limited experience, and I do not want to contribute to that. However, I want to give you some good advice based on what I believe is the best workflow for using IRs and so just note that I am leaning on my rather deep experience with two notable companies: Ownhammer and York. As an philosophical aside, I prefer to be well read rather than widely read.

Ownhammer has been around a long time and is a household name at this point. York is a bit newer to the sale of IRs but has actually made a few IR packs with Ownhammer. He has a good ear and make some very nice, curated mixes. Plus he has a lot of experience playing professionally. I’ve mostly used these two companies based on available speakers I was interested in and their good reputations. I don’t think you can go wrong with either, but there are a few notable differences. Here is how I would go about selecting some IRs.

  1. Buy a pack from a company that has a capture of the speaker that you want. If the other one doesn’t have it, then it is an easy choice.

  2. If they both have it, get the one in the cabinet you want. If only one offers a 4x12 or 2x12 which is the case with OH and York’s DV-77 packs, then the choice would be obvious.

  3. All else being equal, decide which organizational method you find most appealing.

Organizational Methods

I am only going to be talking about microphone mixes here. Single microphone captures are already baked into the Helix. If you really want a single mic file from a manufacturer then you probably aren’t reading this post or you know what you want, so go get it. For me, its the mixes that I am after.

1. Curated Mixes

York has fairly curated mixes. The mixes come in a folder with a guide that tells you what microphones were used. They are all the classic mixes and they all sound great. It is a tight, low option curation of the best sounding mixes. But York does not put any noticeable effort into organizing them by what they sound like or how they sit in a mix. That said, you usually get 10-20 mixes, and usually around 15. York does have single mics included in the packs but they aren't organized either.

2. Focus on How it Sits in Your Mix

Ownhammer’s newer RockBox packs are in 4x12 Cabinets only and are designed in such a way that they organize the mixes by Classic, Blended, and Modern (Focused and Forward, Blend, and Scooped and Big Sounding). Then they have 5 mixes for Classic, ranging from Forward in the mix to Laid Back in the mix, and 5 sub-mixes for each of those levels of Forward or Laid Back for a total of 25. They also have 5 mixes for the Blend and 5 for the Modern cabinets. One of my other RockBox packs has the addition of a Tall set of 5 mixes from a "Vintage Tall" cabinet.

This differs from some packs because there is not one mention of what microphones they use in their document. Some people hate this. You are expected to pick a starting point for what you think will work for you, then use the different mixes from there to sculpt where you want your sound to be. The mixes sound great and I like this system.

3. Focus on Descriptive Terms

The other Ownhammer packs are labelled closer to what is more typical of IRs creators. Many of these sorts of packs don't tell you the speaker, but it's probably a V30 because they seem to be aimed at metal players. I think most people would find getting a pack for the speaker and cabinet that they like better than a genre specific pack like "Modern Progressive Essentials". The mixes are usually labelled with a descriptive term that I feel vary from somewhat useful to useless. In my opinion, the useless ones far outweigh the number of useful descriptions. That is not to say they are bad mixes, but they aren't friendly for navigation. For example, "Beef", "Chunk", "Iron", "Paradox", "Earth". I don't even think the creator could tell me what the difference between "Beef" and "Chunk" is without listening to it.

When you pick up a speaker pack you know what you are getting and you can enjoy an easier workflow of selecting an IR via a description of how it sits in the mix. In the RockBox packs, I immediately know that going from the Classic to the Modern is going to be a more scooped sound, and going from mix 5 to 1 will be going a change from a darker tone that is laid back in the mix, to a brighter tone more forward and present in the mix. Sort of like moving a microphone around on the Helix, with the benefit of having the work already done for you and then not having to worry about blending mics or getting the levels just right. It is quicker and easier. On the contrary, auditioning 100 vaguely labelled mixes is not saving me any time and not reducing my analysis paralysis. I do not want to spend time and sanity doing an A/B of "Fire" and "Smoke" let alone "Beef" and "Chunk"; it is borderline offensive.

My opinions on Impulse Responses and Speakers

Therefore, in my opinion, based on my own experience, I would aim to get either get a small selection of curated mixes like York, or a pack like the OH RockBox that has a sane labelling scheme. If you really need to know the microphones used, the York has that. However, if you want the quick way of identifying the mix you should use something like the RockBox packs. Otherwise, you either have to audition the IR or know generally what the microphones used sound like. In that case, you might as well just use the Helix Cabs to fine tunes things a bit more to your liking and they are "free".

Personally, I have had great luck with an Ownhammer IR from their "Studio Mix Collection". made over 10 years ago, and I am currently spending more time trying IRs and Helix Cabs that might fix some of the issues I have with my current IR. For those of you that might ask or care, the IR is the EVM-12s speaker in the 4x12 Marshall, the Median mix. It sounds really great and I like it a lot. It seems to work on everything, but maybe also might be sub-optimal on everything. Who's to say! It does have a looser low end frequency response that I sometimes have to wrestle with which is the reason I am trying new things. That and the boredom of the same IR all the time. Oh look! A shiny new thing!

Now, I am auditioning the Ownhammer RockBox EVM-12L, DV-77 (great speaker, I want one in the Helix), the Scumback J75-PVC, and the Red Coat Guv'nah (I picked this up before they released the Helix one). They all sound very good and the character of the speaker shines through. I know this is a bit of a digression but I think it serves to show that speakers change your sound in a major way and if you aren't happy with your sound, it is probably the speaker. Dave Hunter describes it as "soul searching" and eventually you will discover what works for you.

My parting words on the topic is this: the Helix cabs are very good and you can get by with throwing a SM57 on the Cabs and applying what you learned here for making it sound good. But third-party IRs are very fun for trying out things not yet in the Helix.

PS: Line6, can you start telling us what speakers are in all the Cabs, please? If I have to guess, I am not using it.

Resources

  1. “Helix Update 3.50 Release Notes” Line6.com

  2. Metal Music Manual by Mark Mynett

  3. The Recording Engineer's Handbook by Bobby Owsinski

  4. Tone Manual: Discovering Your Ultimate Electric Guitar Sound by Dave Hunter

Previous Posts


r/Line6Helix • • Apr 23 '26

General Questions/Discussion Hot off the line :D

Post image
303 Upvotes

Anything you wish you knew immediately after getting yours?


r/Line6Helix • • Oct 08 '24

General Questions/Discussion Steal of the week - Only paid $700 for this Helix and bag.

Post image
303 Upvotes

I’m not trying to encourage lowballing, but sometimes you win.


r/Line6Helix • • Oct 03 '25

General Questions/Discussion My new Stomp

Post image
289 Upvotes

I posted some days back debating between HX Stomp, Ampero Stomp, and Nano Cortex. Landed on this awesome one! Currently running it through a Katana Gen 3 Artist, power amp in. Thanks for everyone’s input!


r/Line6Helix • • Oct 22 '24

Meme/Shitpost He’s helping w toan.

Post image
286 Upvotes

r/Line6Helix • • Sep 23 '24

General Questions/Discussion Wish me luck fellas, this is my first modeler.

Post image
275 Upvotes

r/Line6Helix • • Jul 30 '26

Meme/Shitpost My new rig!

Post image
265 Upvotes

First modelling hardware I've owned I decided to go big with the XL and a Laney LFR 212.

Will be having lots of fun over the coming weeks diving into what this baby can do!


r/Line6Helix • • Aug 05 '25

General Questions/Discussion Scored for 400 bucks on fb market 👌

Thumbnail
gallery
259 Upvotes

This is my first ever pedal as well would appreciate some tips on how to get some good tones


r/Line6Helix • • Aug 20 '24

General Questions/Discussion Still can't believe I got this for $800!

Post image
240 Upvotes

Mint, basically unused with official gig bag! Haven't updated etc yet, but I'm super stoked to be apart of the Helix community now. Now to get an FrFr...


r/Line6Helix • • Sep 05 '24

General Questions/Discussion I look at this pic whenever I gas for a Floor or LT

Post image
239 Upvotes

Fits two cables, power supply and stomp like a glove. Don't need to carry anything else


r/Line6Helix • • Nov 16 '23

General Questions/Discussion Helix/HX 3.70 Is Now Live

215 Upvotes

Helix/HX 3.70 is now live. Go get it! Oh, and as always, READ THE RELEASE NOTES! https://line6.com/.../helix/helixhx-370-release-notes-r1052/


r/Line6Helix • • Nov 06 '24

General Questions/Discussion Simple quality of life improvement.

Thumbnail
gallery
214 Upvotes

My wife bought a label-maker, and transferring the input and output icons to the top is such a nice improvement.