r/lasers • • Aug 09 '25

(Why) Are EDM show lasers not dangerous?

Post image
1.1k Upvotes

Whenever I see videos of EDM raves and whatnot, I've wondered, with so many lasers and them being bright, how does nobody go blind? I want to go to one, just not sure if I need to worry about going home blind.


r/lasers • • Jul 23 '26

80W blue laser

1.0k Upvotes

r/lasers • • Feb 16 '26 Bravo

Melting Metal At 40ft With DIY 1000W Rifle

882 Upvotes

Just testing out my new expander. It can burn at much longer distance than this, but this is the safest setup I can do here(other wise beam might leave my property). Also, I added a monocular camera based scope, this makes the beam visible.


r/lasers • • Mar 15 '26 Popcorn

40w Goldeneye Laser Watch Melting Steel

824 Upvotes

NOTE: it's a bit hard to see the steel strip, but it does melt the top of it. 40w is bare minimum to melt small strips of steel.

This is the first test of my Goldeneye laser Watch replica. It's made with a 40w Ir pump, and my custom built lipo felixble wrist battery. It's not super pretty, but it is working. I hope to clean it up a bit and make it look nicer. The wrist battery(brown leather material under watch strap) is much more bulky than I thought it would be. Speaking of which, this battery barely has enough power to power this. It needs close to 70w electrical, and that's pretty much maxing these little cells out. It's made from 6, 220mah lipo cells, 2 in parallel, 3 in series, which makes around 12v. It's set up to charge using a drone battery balancer.


r/lasers • • Jan 28 '26

1000W Laser Gun Early Test (possible first?)

792 Upvotes

Note: There is no external power supply, batteries are all mounted to the butt of the rifle. This is a quick test fire of my sketchy looking 1000w laser gun. If you turn up the volume, you can hear the snap crackle pop of gravel disintegrating from the beam, which leaves a trail of glass. The device is not done yet, but it does function. And yes, this is built into a nerf gun. It's worth noting that it's not reaching full power yet(reaching likely around 700w). It's possible the button trigger is the bottle neck, even though the button claims 50a rating. These batteries should easily be giving 40 amps, but it always seems to land around a max of 26 amps. The fans haven't been added to the heat sink yet, but it stays cool enough for shorts tests like this. With the current lens setup, it can burn around 40-50 feet distance. With a large enough beam expander, I'm sure it could easily burn things near half a km if held steady on a tripod. I might test this on a cheap drone, see if I can take one out of the air during flight.


r/lasers • • Dec 06 '25

500-watt laser igniter, decisive and effective.

668 Upvotes

r/lasers • • Jul 29 '25

RIP this dudes eye balls

Post image
444 Upvotes

For context these are absorption-based laser safety glasses for UV and IR radiation. Imagine throwing away the glasses that were actually protecting you lol


r/lasers • • Aug 28 '25

Aight which one of you did this

425 Upvotes

r/lasers • • May 04 '26 WOW

tinyRGB worlds smallest RGB pointer

Thumbnail
gallery
387 Upvotes

Hey Girls and Guys!

I build what probably is the smallest full color analog laser pointer. It’s lighter sized and has an integrated lipo with USB-C charging port.
I has fully corrected single mode diodes: 455nm + 520nm + 638nm packing a total of roughly 400mW of output.

Due to the beam being prism formed, it’s completely round at the near and far field.

It even got some nice color changing modes that allow you to draw POV colored shapes.

Last two pictures show the far field beam at roughly 20m before and after alignment. All colors are nicely aligned and show almost the same divergence!


r/lasers • • Sep 27 '26

Reminder to use the right glasses.

352 Upvotes

The green(520nm <5mw + <1mw) passes right through the glasses. The 405mw(class 4, objectively more dangerous)does not.


r/lasers • • Feb 05 '26

Unfocused 1000w Pump Acts Like A Flamethrower

295 Upvotes

The beam size unfocused was 2.5x4 inches wide. With enough power, any beam size can burn!


r/lasers • • Sep 01 '25

Bro I just created a quasar with perfect focus

Thumbnail
gallery
224 Upvotes

r/lasers • • Aug 18 '26

Yes

Post image
196 Upvotes

r/lasers • • Aug 12 '26

My brother is in a house exactly 2.5km from me (measured on Google Maps). I told him to record a video to test my 10W blue laser.

189 Upvotes

r/lasers • • Sep 19 '25

Picked up one of those "40w ir cannons" that have been popping up from China and dang it is powerful. Just needs a lens to adjust the focus further than 6in away.

180 Upvotes

r/lasers • • Oct 12 '26

Setting up and firing a 500W high-power architectural laser system

176 Upvotes

r/lasers • • Nov 27 '25

100w Handheld Fiber "Laser Igniter" - First Thoughts

Thumbnail
gallery
175 Upvotes

Update, unit is having battery issues, post here: https://www.reddit.com/r/lasers/comments/1p90wp6/comment/nr90ty1/

First off, I want to confirm that these "100w laser igniter" devices from China, are in fact real. The power output is most likely in or near the 100w range as they claim, since it cuts through steel without any focusing or lense.

With all that said, there are some red flags. In the image with the front cap removed, we can see some issues. I'm no electronics professional, but seeing a huge bundle of wires wrapped around a red hot heat sync doesn't comfort me. Speaking of heat sync, the cooling is very minimal for this unit, likely not enough for long durations. I personally wouldn't run this for more than 20-30 seconds straight without cool down. This unit has no lense at all, and I was fully aware of that when I bought it, and yes, the divergence is bad. I didn't buy a lense(Some units include lenses) since I wanted to spend a minimal amount of money on this thing to make sure it worked.

In conclusion, it works, and it's powerful. But It goes without saying, this thing is incredibly dangerous. Please do not buy it unless you have experience with high powered lasers. Treat it like a fire arm, and always wear laser glasses spec for the 1000nm range.

I might do a full video review soon. These are just my initial thoughts.

Disclaimer: I'm sharing the link here, but I am not responsible for any stupid crap anyone does with these things, nor you should you buy these unless you are already experienced in lasing!

Link: https://laserigniter.com/product/laser-igniter-100w-005/?v=63c9ab07b0ba


r/lasers • • May 31 '20

Glad to see this sub active again! Here's my 7W 450nm laser I built a few years back

Post image
167 Upvotes

r/lasers • • Feb 20 '26

Extremely Irresponsible Alibaba Ad...

Post image
161 Upvotes

Just saw this insane ad from Alibaba. The 'Safe for kids' label is sickening. Judging by the size, this is likely in the 200-500w pump range, with a 20-50x beam expander attached.


r/lasers • • Dec 13 '25

40W laser igniter, fan version

161 Upvotes

r/lasers • • Jul 08 '26

Rate my laser collection! (first time poster)

Thumbnail
gallery
152 Upvotes

This is my first time posting about my lasers. I started collecting about 15 years ago. I’m somewhat of an enthusiast (been a fan of Styropyro since he was a small channel)

2010- 100mW 650nm (no brand $56) —pops balloons!
2012- 1W 445nm (O-like $168) —first burning laser
2015- 50mW 589nm (Spartan $445) —rarest color
2015- 100mW 532nm (Lazerer $58) —smallest
2023- 5mW 510nm (Aliexpress $20) —minty color
2023- 15mW 488nm (Aliexpress $40) —favorite color

I’ve excluded the 1W blue laser in some of these photos because it washes out the others.

My two absolute favorites are both the yellow and cyan colors. If I mix them together it creates stark white!

Hope you enjoy!


r/lasers • • Jun 15 '25

HUNDREDS of laser pointers aimed at our plane coming out of Tana, Magascar.

152 Upvotes

r/lasers • • Jun 29 '20

PLEASE invest in quality laser safety eyewear

151 Upvotes

My apologies in advance for the rant...

I have seen numerous recommendations here for laser safety eyewear from companies who I would not trust with protecting my vision. Such products are not guaranteed to be tested as per the ANSI z136 standards (EN207/208 for those in Europe). Some companies even have disclaimers right on the product websites claiming the eyewear is not meant for situations where safety is regulated.

People are lucky if we have 2 working eyes. Laser radiation is a hazard to be taken seriously. The aversion response (blinking or looking away) can help prevent injury for lower powered laser but generally speaking, when we start moving into Class 3R and absolutely climbing into Class 3b and Class 4 lasers, the aversion response cannot be relied on.

The eye is an amazing muscle capable of focusing images (up to 100,000x) and serves as a direct connection to the central nervous system via the retina. If people are going to buy lasers, they should invest in quality protective equipment. Some damage to the eye such as a cornea burn may be able to recover relatively quickly thanks to the crazy high metabolism of those cells, but damage to the retina...why risk permanent damage?

Furthermore, if you do not know this already, take time to learn about laser safety. Familiarize yourself with terms such as irradiance/radiant exposure, Maximum Permissible Exposure (MPE), and learn how to calculate the optical density required for your laser or the laser you are looking to purchase.

There are a lot of reputable companies producing quality laser safety eyewear who test to rigorous standards (The ANZI z136 series even includes a standard specifically for Testing and Labeling of Laser Protective Equipment (ANSI z136.7). Please, please, please, do not risk your vision by choosing affordability over quality when it comes to laser safety!


r/lasers • • Sep 09 '26

wow RGB Handheld complete

150 Upvotes

I finalized the Numb12 array handheld. It has a self-contained battery with charger, 3ch custom linear CC regulator, independent pots and switches for each color. A 96% Eff. LT8705 Buck converter powering a common 20.5v rail for each channel.

**Green rheostat came damaged. There is a nick in the coil causing high resistance until close. Will repair or replace in future. Didnt catch on assy.

Im working on finding the right cylindrical lens power/distance to correct red after several measurements. Will update when/if found. One looks promising.

Wont let me share video + images together. I got purple, lime green, orange and a light yellow mix pictured. Considering green is either .7a or 1.8a