r/EngineBuilding • • Dec 03 '24

Help getting into engine building?

I’ve always wanted a c4 since I was a freshman in high school I was finally able to get one and was lucky enough to find a 92 lt1 with a 6 speed it already has headmen headers a lunati cam 1.6 roller rockers ls style springs keepers and retainers also chromoly pushrods 24 lb fuel injectors 7/16 studs and guide plates a 52 mm throttle body a cold air intake and an aluminum flywheel I know enough about engines to understand the functionality of these parts separately but I know motors can be very picky with just small part changes as far as air flow and exhaust part tolerances etc I’d like to get a crisp crackly nascar kinda sound but I’m not sure how I’d go about it are these good mods thst I have? How much of a hp gain from factory do you guys think I already have? Also anyone care to guess the specs on my cam I know that has a lot to do with things and different builds

0 Upvotes

91 comments sorted by

16

u/Thefirstofthree Dec 03 '24

Not tryna be a dick but you essentially wrote a long paragraph with no relevant info in it.

What cam do you have? Not the name, but the details. Lift, overlap, etc. pushrod length? Fuel management system? Differential gear ratios? OEM or aftermarket pistons? Steel or aluminum driveshaft? Heavy or lightweight flywheel?

There's a lot that goes into attempting to calculate power at the wheel, but even then, theory does not always match reality. A dyno run is the only way you will know for sure how much power you are putting down.

One last thing, you're in a super detailed engine sub asking about exhaust sounds. Kinda the wrong place lol. Just slap a different exhaust on it. You want raspier? Slap an H-pipe after the headers and cut the mufflers off. Personally, I like how flow master super 10's sound on 302s and 350s

-4

u/Nice-Employment849 Dec 03 '24

I didn’t list cam specs cus idk them don’t know the pushrod lengths either stock ecm stock diff gears oem pistons driveshaft is aluminum I believe lightened aluminum flywheel I listed the specs for what I know what I was looking for was more of a hey get these heads this cam this crank etc as sb2.2 engines are still small block chevys and not far in dis placement from my engine I figured it couldn’t be that hard to get a stock block to at least sound like or come close to what the sb2.2 and ro7 engines sound like I’ve def seen cars with my same motor on YouTube with some combination of parts that get it to rev to 7 grand and sound the way I like I just usually have a hard time reaching out to those guys to get build sheets there’s gotta be some combination of heads or head porting or rockers or springs or valves pistons crank etc that make this possible

4

u/Thefirstofthree Dec 03 '24

Wish I could help more but I'm more of a Ford and Toyota guy. Not the most knowledgeable about Chevy small blocks.

But generally the rule of thumb is more aggressive cam profile = more aggressive/lopy engine rotation. Combine that with a good exhaust setup (like a flow master super 10 and some long tubes, or a full borla setup) and you'll probably be pretty close to what you're looking for.

I don't know if they support SBC, but AFR made the best goddamn heads on the planet for the SBF 302.

-3

u/Nice-Employment849 Dec 03 '24

This is great thank you finally somone willing to say “I don’t know” instead of making fun of me or acting like I didn’t ask a clear question 😭also just fyi I’d already done my research and what you said exactly lines up with what I’ve read on forums YouTube comments and what I could surmise from my own limited hands on mechanical knowledge I just wanted to see what Reddit had to say and from my observation I would’ve done ok with what I learned myself a lot of these guys on these subs don’t know nearly as much as they’d have you think as a 22 year old who’s only ever had one car (the one I have now) I’ve found my knowledge can surpass a lot of the guys I’d consider “qualified” that I run into on here

3

u/Thefirstofthree Dec 03 '24

Some of the old guys in here have tons and tons of useful info, you just gotta ask them the right questions.

I also bought a modded V8 in my early 20's, the best advice I can give you is don't cheap out. Buy good parts, I know it can be rough (I was broke lmao) but it's definitely worth it when you don't have to worry about shit breaking every other week.

I didn't know shit about engines or anything before owning that foxbody and boy was that car a painful teacher lol. I got it when I was 21. 26 now and can build a car from the ground up

1

u/Nice-Employment849 Dec 03 '24

In your opinion would it be better to build off what I have and maximize the $$$ the previous owners already spent on parts or comepletely start over and treat the motor as stock as far as buying performance parts it already has some of the stuff on here isn’t cheap like the cam and the three row rad as well as the c5 wheels and brakes and the bolrla x pipe and headmen headers it’s got some good stuff already right? Also dual friction clutch and sway bars from Van steel it is indeed somone else’s project but they clearly loved it it’s got easily in aftermarket parts what I paid in cash for it I’d give a complement list but it’d be as long as this paragraph even if I left out small stuff like the high flow injectors

1

u/Thefirstofthree Dec 03 '24

Tough question. I would say if compression is fine, just run as is and play with exhaust before tearing into the engine.

As for keeping the mods vs starting over, if you're gonna build off what you already have, you really need to know the specs of all those parts.

OEM will always be easier, but aftermarket is where the power comes from. But with more power, comes more math and measurement to make sure the new power added doesn't grenade the motor.

If it were my car, I would run it until it blows and then do a fresh build from the ground up. Don't fix what ain't broke, and save up for when it is.

-3

u/Nice-Employment849 Dec 03 '24

Advice from somone who’s sympathetic to my situation and has been where I am is always highly regarded thanks brother was just trying to decide if I want to spend 800 on an opti when I can find one for 300 but it looks like I have my answer!

1

u/SpudDispensaryCo Dec 04 '24

I would also be careful, is it tpi or tbi?.

1

u/Nice-Employment849 Dec 04 '24

I think lt1 was tpi

1

u/whipsnappy Dec 04 '24

Well that's one heck of an unpunctuated sentence

1

u/Nice-Employment849 Dec 04 '24

I can’t do punctuation at the same time as being fast and I was busy lol

1

u/SpudDispensaryCo Dec 04 '24

Need to know diff gearing, that plays a crucial role in speed.

1

u/Nice-Employment849 Dec 04 '24

It’s stock factory specs for a 92 manual transmission corvette

3

u/v8packard Dec 03 '24

I can't guess at output with what you posted, it could even be less than stock. If I am reading the post correctly, it's difficult to read, you probably do not have or want an aluminum flywheel. These cars with the ZF 6 speed used a dual mass flywheel, stock. Yours might have been replaced with a single piece flywheel. Hopefully, it's a steel not iron flywheel. Aluminum flywheels are terrible in street cars.

You should consider a few things about your car, and none of this is a criticism. The ECM takes PROM chips, and I think is still batch fired. Tuning a combo that is anything more than mild can be a chore. Your rear differential could be a 3.07 ratio, or a 3.45. Neither ratio is ideal for a big cam.

Learn to work with the strengths of your engine. The LT1 can and should take more compression than a typical small block. Keep that and your gearing in mind when you think about a cam.

0

u/Nice-Employment849 Dec 03 '24

The car def stalls very easy on the street not like anything is wrong with it but I’ve ridden Harley’s extensively and I’d say it feels more like a motorcycle

0

u/Nice-Employment849 Dec 03 '24

Prob the flywheel

0

u/Nice-Employment849 Dec 03 '24

Combined with the cam and the needing an optispark

1

u/v8packard Dec 03 '24

Needing an Optispark?

I really think if you had an aluminum flywheel it would be nearly undriveable.

1

u/Nice-Employment849 Dec 03 '24

It’s an optical distributor pita to replace

2

u/v8packard Dec 03 '24

Don't fall into the overblown trap of criticism the Optispark. GM eventually corrected the tendency of the early distributors to fail because of moisture. People have been complaining for 30 years despite having the answer right in front of them. If yours works, it's fine. Avoid drowning it.

1

u/Nice-Employment849 Dec 03 '24

Mine is currently a no start and throwing a code only for the opti I think it needs an new one also I felt in there and there is about an inch of grime caked over the whole area from the water pump leaking

0

u/v8packard Dec 04 '24

A coolant leak can kill any distributor, not just the Optispark.

That much grime after a cam swap?

-1

u/Nice-Employment849 Dec 04 '24

The cam was done years ago and my car doesn’t have a distributor it has an OPTISPARK

1

u/v8packard Dec 04 '24

The Optispark is a distributor.. oh boy..

0

u/Nice-Employment849 Dec 04 '24

If you had an lt1 you’d know what I’m talking about it is bc a distributor in function only it’s completely different than a regular one

→ More replies (0)

1

u/Nice-Employment849 Dec 03 '24

Damn if the po lied about that I wonder what other “mods” Hes fibbed about

0

u/v8packard Dec 03 '24

I don't know for certain what is or isn't in your car. But I have seen what an aluminum flywheel is like. I think you would be saying things very differently if you had an aluminum flywheel.

1

u/Nice-Employment849 Dec 03 '24

Maybe it’s just lightened ?

3

u/Thefirstofthree Dec 03 '24

Can confirm what Packard is saying. I had an aluminum flywheel on my fox, that thing was a fucking nightmare at red lights and city streets

2

u/acab415 Dec 03 '24

A lot of that snap comes from high compression.

1

u/Nice-Employment849 Dec 03 '24

But is it strictly high compression? Does that mean in raising my compression in the cheapest way possible (domed pistons and high comp head gaskets) I could get a similar sound?

0

u/acab415 Dec 03 '24

The first thing I’d do is get a good exhaust built with an x pipe and maybe Gibson mufflers.

1

u/Nice-Employment849 Dec 03 '24

It’s got a borla x pipe with 3” duals all the way to under the driver and passenger seat

2

u/Thefirstofthree Dec 03 '24

Long tubes, x-pipe, and 3" tubes is basically the standard for old V8s. Personally, I like H-pipes on pushrod engines bc of the deeper sound it gets. (Debatable but marginally better for low end torque too)

0

u/Nice-Employment849 Dec 04 '24

I’ve heard that

1

u/Nice-Employment849 Dec 03 '24

Is that good? It’s also got headman long tubes

2

u/FlightAble2654 Dec 03 '24

Put glass pack mufflers on it!

1

u/Nice-Employment849 Dec 04 '24

It has none I will be adding none straight pipe the world

1

u/FlightAble2654 Dec 04 '24

Buy they make the noise you are looking for.

2

u/Nice-Employment849 Dec 04 '24

Ok maybe will consider now that you say that

2

u/WyattCo06 Dec 03 '24

So which is it? Has a nice of chop, you want a Nascar engine sound, need to build the engine, needs an optispark because it isn't starting?

1

u/Nice-Employment849 Dec 04 '24

As far as the chop I think I just need to raise the idle a bit it already sounds like an older one a bit at high revs

8

u/ProfesorBong Dec 03 '24

If you’re serious about wanting to get into engine building pull the motor, disassemble, measure and find part numbers or identifiers for whatever you have questions for. You’ve bought someone else’s project car and everyone here knows it, you’re not going to be taken seriously or find the answers you’re looking for on this sub unless you prove you’re serious about building your motor by asking the right questions backed up with actual specs.

8

u/WyattCo06 Dec 03 '24

This mofo is looking for an exhaust shop. Not to build an engine.

2

u/WyattCo06 Dec 03 '24

Bro. You've been posting about this car for a month now.

2

u/Nice-Employment849 Dec 03 '24

This is my first post in this sub wym 💀

2

u/WyattCo06 Dec 03 '24

I mean you're full of shit. That's what I mean.

2

u/Nice-Employment849 Dec 03 '24

Is everybody in this sub so hostile???😭

4

u/[deleted] Dec 03 '24

Yes. This sub is awful to beginners. 

2

u/Nice-Employment849 Dec 03 '24

You must hate whatever you drive lemme love my car dude posting on Reddit aint illegal Mr Reddit police

2

u/WyattCo06 Dec 03 '24

Gloat about your POS in a sub that gives a shit about it.

1

u/WyattCo06 Dec 03 '24

Sit tight and find out.

You've constantly posted about this car. It's practically vintage.

I do not feel you're trying to get into engine building. I think you're begging for nut huggers and praise because you bought this "thing".

1

u/Nice-Employment849 Dec 03 '24

Yea cus the long ass paragraph I typed had nothing to do with engines and everything to do with looking for praise I’m not gonna call you out on the internet but I got you pegged buddy

2

u/WyattCo06 Dec 03 '24

Do you know where the radiator cap is?

2

u/Nice-Employment849 Dec 03 '24

The cars cold rn smartass but good try

2

u/WyattCo06 Dec 03 '24

It was just a question.

3

u/Nice-Employment849 Dec 03 '24

It’s on the passenger side close to the base of the windshield

2

u/Thefirstofthree Dec 03 '24

I would assume on the radiator lol

0

u/Agent_Eran Dec 03 '24

nope.

1

u/Thefirstofthree Dec 03 '24

For my curiosity, where is it on this car?

→ More replies (0)

-1

u/Agent_Eran Dec 03 '24

Im w you Wyatt

2

u/MonteFox89 Dec 03 '24

Bro, this sub or not, you've popped up on my feed more than anything else... and I love lockpicking, but here's a c4corvette with a rebel flag and a black hood 😅 you seem like you're proud of your car bro. To get into engine building, just start. Do some reading, figure out 100% what you got and see what can be changed. Exploration and experimentation are the building blocks for hobbies like this :)

1

u/Nice-Employment849 Dec 03 '24

Nice thanks did u read the post? Any thoughts on the questions I asked hehe

-3

u/MonteFox89 Dec 03 '24

Yeah, I've read it, someone's modified a 350. For all we know, it's only floating 350 horseponies. Stock is 300 iirc. I'm a diesel tech and got out of gassers a while back. Still build diesels at work... this information may be a bit wonky considering I haven't dealt with a gasser in a long while... however, its hard to really pull more than 450 without spending the money... cheaper to build an ls. Anyways, you want that nasty fuckin sound. Change your cam for longer duration. That's what makes that chop...

1

u/Nice-Employment849 Dec 03 '24

It already chops ok I want that buzzsaw zipper kinda sound like a nascar when you rev it sounds like that combined with shaking a bag of wrenches

2

u/MonteFox89 Dec 03 '24

That's gonna take some work... you should google Nascar engines. I don't think you're gonna do well with the 350 trying to do that... they get in really in depth... so much so that for a normal person, we call it debt, not depth.

1

u/Nice-Employment849 Dec 03 '24

Debt not depth is hilarious 😂 I just thought maybe with some heads with bumped comp with my cam and exhaust I could replicate the sound

3

u/MonteFox89 Dec 03 '24

You could always try for it, not my pockets 😅 personally, when I get the money available, I'll get back into it. I have an LS waiting to be stripped and built up for my 72 monte carlo. The 350 in it only runs 5psi oil pressure at stops now.... :( apparently, driving on the interstate at 90mph in 3rd gear on 410s is not good for the engine... dog died that day anyways, so did that engine essentially... :(

2

u/Agent_Eran Dec 03 '24

cheaper to build an ls

no it isn't.

-2

u/MonteFox89 Dec 03 '24

Power to money ratio... sure is.

1

u/Agent_Eran Dec 03 '24

wtf are you talking about?

0

u/MonteFox89 Dec 03 '24

Idk man. I had this elaborate shit to say in response... been sick for 2 days... precovid, same money to build a 350 to 400hp can get you an ls with more power...

2

u/Agent_Eran Dec 03 '24

thats just not true IRL

LS hard parts cost way more.

→ More replies (0)

3

u/Agent_Eran Dec 03 '24

 and I love lockpicking, but here's a c4corvette with a rebel flag and a black hood 😅 

very annoying that this is happening. been trying to ignore this car but its following me

3

u/Agent_Eran Dec 03 '24

lol. thats why ur getting roasted here w that POS.

are you going to make another 25 posts??

0

u/SpudDispensaryCo Dec 04 '24

Here’s my two cents, it’s a 91 lt1, lt1 is a great engine you can modify it. But it’s not like modifying a carb, too much came over lap can make it run like shit, due to the tpi, it can be very hard. Most modification will require prom retuning. All the way down to shift points. I would find the specs of your current cam, find a cam that you like the powerband. High end, low end. Look into a good set of heads or even have your heads taken to a machine shop. These cars got squirmy under 350hp, so you don’t need 500, and it would be a stretch to build this to 500. Once you’ve done that, make sure all your parts align with themselves, you’re not bottlenecking anything. You don’t want a little carb on a big engine. That’s an example of bottle necking, once your heads have been done, you’ve found a cam that you like install it. Or change the lobe separation on your current. But in all honesty what’s done to it should be a really fun car.

1

u/Nice-Employment849 Dec 04 '24

It really is super fun and satisfying to drive and rewarding especially with the manual and it sounds great and has all the power to back it up also probably weighs only around 3k I’ve don’t a lot of weight saving where I can

-1

u/Nice-Employment849 Dec 03 '24

I’m sorry I should’ve said this but if your not directly responding to questions I asked in the post pls take it somewhere else I just need experienced help building my sbc bro not an excorsism