r/DieselTechs • u/Formal_End5045 • 5h ago
r/DieselTechs • u/Sadman3278 • 1h ago
Working at a dealership for the first time ever as a Red Seal
Hello!
I have been a fleet and mobile mechanic for 5 years now. My first 2.5 years were in a shop and calls then I spent 2.5 years doing calls only but my workplace has completely fallen apart and I want to get better at trucks so I went out and got hired at a Freightliner dealership.
I have a full set of tools built up over the last 5 years so I think I’m good in that regard. What I’m nervous about is that a LOT of my experience has been on trailer and forklifts but apart from servicing I have not done too much on trucks in the last 2.5 years so I am rusty. I do check engine lights but not frequently. I have not replaced a clutch or removed an engine before. The service advisor at my work who has 6 years of experience at a dealership told me I’m a great mechanic and will do fine at a dealer but I am nervous especially being a red seal already and being at the top of the pay scale that they won’t be happy with what I’m inexperienced at. For heavy work I’m very good and efficient, air systems and valves I’m very good, wheel ends I’m very good. It’s quite honestly truck electrical and engine work/check engine lights that I am afraid of. Has anyone been in my shoes and have advice for me? How to not get fired? I’m a quick learner and there’s plenty that I HAVE done, it’s just the things that I haven’t done that I’m worried they will not be happy about.I was honest in my interview though.
r/DieselTechs • u/Efficient-Willow11 • 21h ago
Rush truck centers
I recently got a offer from Rush Truck Center as a Level 4 field technician. I am curious if any of you in here have had experience. If so what are the hours like, work load, type of work, on call, weekends? Anything helps so please share what you can. Thank you!
r/DieselTechs • u/Wrong_Sprinkles_3122 • 1d ago
Check it out! First time Running a Monaco Counterbore cutter!
My first time today running a Monaco setup to cut the block . Turned out real well . The tool itself cut very smooth with minimal to no chatter . Very accurate too.
Cut the counterbore to .0310 , shimmed out .0324
Cut in increments of .005 until I was sure the tooling was 100% even .
Final measurements came out to .004 protrusion even on 4 spots . Right on the money 💪🏽
This engine originally had crazy low liner protrusion. The worst average was around -.010
r/DieselTechs • u/No_Walrus_3638 • 2d ago
We all know that engineers just want to piss us off...
Just wanted to share this little SOB. It's sole purpose appears to literally just be in the way and piss mechanics off. Today was the first time in 7 years I've been working on a fleet that is all Cummins isb 6.7 that I had a # 6 cylinder exhaust gasket blow. I had the new kid tackle it because I'm evil.... Lol
He was having such a hard time getting anything on the damn bolts. So I has like "c'mon buddy... It's really not that difficult." So then I tried to give him a hand and every thing we threw at the bolts would cam out. I was thinking, from my vantage point this stupid piece of tin was under the bolt and not just sitting on top of it literally just being a dick.
I was like buddy you striped the bolts. That's why nothing will grab we may have to cut the heads off. Then by mere chance I knocked this piece of shit off and was like 😲😦🤯😤 WTF! I SWEAR THEY LIVE TO PISS US OFF!! DUMB ASS ENGINEERS AND THIS SILLY ASS CONTRAPTIONS!!! THEY KNOW DAMN WELL WE CANT FIT THE DAMN SQUARE IN THE CIRCLE!!!! THEY EXPECT US TO JUST KNOW THIS SHIT! Lol anyway.... I'm an idiot and I'm the one teaching this young man the ropes... He is doomed.
r/DieselTechs • u/LuminisPatrem • 1d ago
Ram 6.7L knock
Reposting here in case anyone has ideas. I’m mostly truck transport, but every so often I get some automotive tossed my way.
r/DieselTechs • u/aFinapple • 4d ago
That looks expensive! What the hell happened here?
This 2018 International HV with an A26 was towed in because it was puking oil from the crankcase vent. What they didn’t tell me is that it had a nasty knock and a misfire. I initially thought I had a bad injector until I saw the oil coming out the vent. I pulled the #1 injector (don’t even get me started on how much of a pain that was), and scoped the cylinder and found massive scoring. I saw some obscure TSBs about wrist pin bushings, but from what I can see here, it looks like the piston was walking in the bore and that’s where the knock was coming from. It was consistent with RPM but would get louder and quieter when you revved it up. Fortunately for me, it’s getting towed to a dealer for them to deal with it, as we’re ill-equipped to do an inframe.
So what happened?
I included pictures of the crosshatching as a reference
r/DieselTechs • u/themexican030301 • 5d ago
Badass!
Just wanted to share something badass I got to work on that you don’t see everyday!
r/DieselTechs • u/1999DaK • 6d ago
General assistance Any PowerGen Field Techs here?
Going from dealer heavy equipment field work ---> power gen field work for a dealer. Some marine due to being an MTU dealer. They allegedly work on anything, and pretty much have the entire greater metro area to service.
What the hell am I in for? The industrial electrical stuff is completely new to me. I was not undercarriage grunt work guy on equipment; mostly software stuff, issues with new systems, electrical stuff, misc other things. I think I might have a shot at learning. It's looking like most of this is just services and load bank testing. Some repair work and new setups. I have no idea what to think at this point and I'm initially missing the familiarity of construction equipment stuff I'm used to. I'm trying to do the best work I can.
I had 6 years in heavy equipment and I'm 2 weeks into field powergen. It feels weird, like I'm an apprentice again. They have me working with other techs. Does anyone with genset experience have good advice for success in this, and is powergen and/or marine a good place to be?
I sometimes like adventurous cowboy shit like fixing stuff in below zero or in a snow storm or whatever, it makes me feel alive; but at this point I want it on my terms.
The pay is pretty much the same here initially.
I try not to take reddit seriously but I know zero people in this industry so I thought I'd give it a shot here
r/DieselTechs • u/maminbrodyaga2025 • 6d ago
Injector problem with QSB 6.7 on hyundai 145w. Update to the previous post
Injector problem with QSB 6.7 on hyundai 145w. Update to the previous post
Previous guys did not install the copper sealings under the injectors... Well we did and it didn't help. We replaced the injector but forgot to replace metal tubes(looks like a carrot or something) that clamps into the injector body to deliver HP fuel from the rail. We replaced those and it did run well.
Also, while waiting for the part, the intake manifold got full with rain water which we syphoned it out. Then we took out the injectors and let it crank so water from the cylinders can escape(1st cylinder only).
Also, we have low turbine speed code. Most probably, it's turbine is still leaking oil since the owner did change only VGT but didn't service the turbine shaft...
Yeah, that's it.
P.S. And during previous week we had a similar engine on a similar excavator with leaking injectors. Though, it did start and idle with carb cleaner. Anyway, this time we refurbished the injectors, mounted them and run. Had problems with shaking engine and somewhat heavy white smoke. I was really scared that it is due to sand getting it's way into the cylinders... A bunch of sand with a similar size as a fist got it's way into the intake manifold while dismounting somethings... We cleaned it out though... Anyway, It turns out that the intake port of 2nd cylinder was stuck closed due to the metal part under the rocker arm popping out from it's place(probably we did install it wrong).
Also, it's ECU was reflashed so the adblue system does not work and we did emptied the nitrogen oxide catalyzator and the soot filter.
r/DieselTechs • u/kerosenedreaming • 6d ago
Diagnostic assistance Intentional neutral float of 20 to 50 volts on a 3 phase delta Y configured 240/120 generator system installed on an old vehicle?
galleryr/DieselTechs • u/TactualTransAm • 6d ago
General assistance Insite
So is there anyway for me to set insite to open up the fault codes tab in the whole work area instead of down at the bottom quarter where you can't see but one fault? At my place we use touchscreen tablets and it's annoying trying to find that one perfect pixel that will let you drag the fault codes tab upward so you can see more at a time.
r/DieselTechs • u/Popular_Outcome_2087 • 7d ago
General assistance is it worth it?
the company i’m with has a some shops across the state. i have the opportunity to transfer to a busier shop , but its less than an hour away from me so the wont assist if i move. the transfer would come with a $2 raise to my hourly pay and more work so likely a higher “commission bonus”. Im wondering if that’s worth the commute until i find a spot to move into myself.
r/DieselTechs • u/Tacolord11 • 7d ago
General assistance Thoughts on what happened?
This truck came in with the rear housing completely torn off on the passenger side and the bellhousing flange broken in the same place on both left and right hand sides. At a previous dealer I worked at, they had a customer with near identical tractor setups that also kept breaking bellhousings from smashing into loading docks and I suspect something similar happened here. Checked U-joints and the U-joint at the transmission yoke was fairly stiff to move but removing the caps I didnt see any apparent damage or excessive wear. I suspect that something shocked the driveline, shoved forward, and pivoted the whole transmission to the right but I honestly dont find that believable and was wondering if anybody else had seen this and knew the cause.
Truck is a pete 348 tractor with a single drive axle, L9, and an allison 3000
r/DieselTechs • u/ShrimpBrime • 8d ago
SOLVED DD13/15 Injector Bosch Crin 4.2 handling and storage. Why, and the repair.
Taking a glance at the internal needle valve, and why handling and storage is so important to this 600$ injector.
Picture #8 is the tarnish on the needle valve step, notice its blackened. Fresh pull, that happened just from disassembly.
The needle valve will immediately tarnish as soon as air hits it causing the needle to get stuck in the cavity. Keeping the injector upright with caps on the inlet ports and bathed in fuel helps prevent the issue and then the injector can be reused later, even after months and years of shelf life.
These pictures will show the tip portion removed and the needle valve. Notice its blackened.
This injector is freshly pulled today and disassembled for your viewing pleasure. The needle valve was not the failure, but when I disassembled the injector, air hit that needle valve and it was stuck.
These can be cleaned and reassembled. The needle valve should move freely up and down at all times. Its located in the tip housing which simply unscrew.
Marked as solved because of it being a known issue. And actually being able to repair without spending a bunch of money on injectors. I hope this helps some of you guys out there!
r/DieselTechs • u/evcant • 7d ago
Tough Foreman
Hey guys, I’m not going to name names or what shop I’m at but I’m an 18 year old apprentice who got hired on right after I graduated, I have a decent mechanical knowledge,( I still know nothing tho). I don’t show up in the shop with any go. I’m pretty humble. I keep to myself. I know when to ask for help and when I’m in over my head. Like, I’m always asking questions because I feel personally that I’m eager to learn. And initially, when I first started my foreman was awesome, there was quite a bit hazing, but it’s nothing I can’t handle. But in the last like month and a half, two months or so, my foreman has been on my case nonstop, giving me the hardest time, and I feel like I’ve been working my butt off and just working myself to the bone. At least that’s how it feels to myself, and I’m just a little lost as to why I’m being treated in this manner. I know my foreman has some family issues going on with his mother. He’s in his 50s, 60s, and I feel like it possibly has something to do with that but I also feel like constantly I’m walking on egg shells and I’m doing something wrong. and to be completely honest, I’m not 100% sure whether this is me issue or a phlegmon issue. Like my phlegmon has been hazing and slowly turned into just like straight up insults where like he told me I should cut myself when I was asking him for a razor blade and a ton of other comments, originally I thought I was just being dramatic and I was being sensitive, but after speaking to a few people around the shop, they feel the same kind of hostility if that makes sense. I’m just looking for some outlook and possibly some opinions. I’m planning on talking to him tonight to see if it is something I’m doing, cause if it is a me issue, I want to address it and I want to improve and I know I’m not gonna be the perfect apprentice and I know I’m gonna mess shit up and I’m gonna make mistakes and whatever maybe, but I feel like initially I was being taught I was learning a lot like I was enjoying myself now I’m just kind of becoming miserable and my job and avoiding my foreman because I know it’s just gonna create issues and just upset me a ton. So if you guys have any advice, comments, anything, on maybe what I’m doing, please reach out. I would love to hear from you guys. Thanks
r/DieselTechs • u/SeethingEmpathy • 9d ago
Everybodys favorite
Notice how new the “old” pump looks, last shop only did pump & filters, no clean out, destroyed brand new pump
r/DieselTechs • u/Wise_Resolution8021 • 9d ago
General assistance IS THIS SPINDLE TOAST
Trailer with 135k. I sanded took some off the top with 320 but still feeling those grooves. Im no spindle expert l. I've never seen a spindle that bad before while replacinga wheel seal. If I replace bearings and races can I run this spindle?
r/DieselTechs • u/No_Walrus_3638 • 9d ago
Diagnostic assistance Thomas C2 Cummins ISB 6.7
Has anyone ever dealt with shutdown in progress message on the dash? I have two buses that like to occasionally display that silly message, but it gives me zero clues as to what the issue is or could be. No codes, bus runs fine. We go to recover and drive it back and the damn thing just drives fine the entire way minus the alarm and the message. Then out of thin air it just decides it's ok. Been dealing with it for a while and I cannot find any info on it.
Open to any ideas lol
r/DieselTechs • u/Suitable-Cable-2280 • 10d ago
General assistance I’m Tired Of Being A Mechanic
As the title says, I’m tired of being a diesel mechanic. Don’t get me wrong I love turning wrenches and learning something new every day, but having to learn over 10 jobs just to be a diesel mechanic is getting mentally draining.
Looking outside my profession I’m seeing electricians splicing wires and installing easy shit, HVAC techs running around with just a multimeter and a bag of tools, welders on their phone most of the time, and forklift mechanics doing a 1/4 of my job just to be getting paid the same as me.
Has a former diesel tech had this issue before? The question I’m asking mainly is which is a stable easy blue collar job that isn’t mentally and physically draining. My body hurts and I don’t want to continue anymore. We’re under appreciated and paid like shit.
I’ve talked to my co workers about this and they said just man up or you’ll get bored doing another job real quick. But I just want stability without destroying my body and ending up like my broken, drained, and angry seniors (Iykyk)
Sorry in advance if i offended you, I also didn’t want to explain the whole thing I could write a book on this.
r/DieselTechs • u/IcePhantom127 • 10d ago
Anyone been to NYADI Diesel School
NYC area. Trying to get into diesel mechanics. Trying to avoid Lincoln Tech as I've heard nothing good about that school.
I tried looking into a few community college programs, but I want to start in January and they don't start until September.
So far, that only leaves me with NYADI as an option, it still has relatively expensive tuition.
Only going to school as I have heard some mechanics say its necessary in today's era to get my foot in the door at a fleet shop, as well as being able to operate on newer computerized equipment.
Is NYADI a reputable school for diesel tech? Are there any alternatives where I can just get a certification instead?
r/DieselTechs • u/Wrong_Sprinkles_3122 • 10d ago
General assistance Can anyone ID this engine stand?
Can anyone ID the maker of this stand? The gearbox has “OHIO” stamped into it but that’s the only mark here .
Found it buried in 3 feet of leaves at a junkyard .
Dropped a coat of black on her, greased the gearbox , and put it straight to work
r/DieselTechs • u/TactualTransAm • 11d ago
Diagnostic assistance Brand new Mack
Air leaks out of this thing when the trailer is supplied. What the heck is it called and is it supposed to 😂
r/DieselTechs • u/CardiologistRemote42 • 10d ago
General assistance Apprenticeship advice
Having a bit of a professional dilemma. In Raleigh NC there is a Caterpillar dealer (bulldozers scrapers construction equipment) called Gregory Poole, and they have a program with the local community college. In that program, Mon-Tues 7-4 is spent in the classroom learning, Wed-Fri 6-3 in the shop as an apprentice. The shop days are paid, the class days are not, but tuition is covered as well as uniforms and tools and other stuff.
The problem is, the salary I’d receive as an apprentice is literally 50% of what I currently make, not livable/feasible. I also would not be able to work at the restaurant at all Mon-Tues. I could still work restaurant shifts W-Sun, but I usually leave around 10:30-11 and would have to be up at 4:30 the next morning. This would be a reality for at least one night a week. I wouldn’t necessarily have to work W-Sun at the restaurant, as the CAT salary would fill in the gaps a little, but there would be at least one night a week where I’d work effectively 16 hours and potentially get 4-5 hours of sleep for the next day starting at 6. This would go on for at least a year.
My boss at the restaurant is a close friend, but I’d be losing a lot of flexibility in the way I’d be scheduled at the restaurant which would make me a less viable employee to a degree. I guess my question is do I suck it up and suffer for a year? Or should I keep looking for something that pays better from the start and has fewer hoops to jump through? Let me know if I can clarify anything further