r/CarAudioFacts • • Jul 29 '24

FYI 10 car audio truths you don't want to hear

9 Upvotes
  1. Skar is a legitimate brand. Their sales clearly say so.

  2. The average buyer that knows next to nothing about car audio is the main sustaining force behind the market.

  3. There is no "best" head unit, EQ, amplifier, component or coaxial set, subwoofer, dsp, or manufacturer. Are Frosted Flakes better than Rice Krispies? Would you engage in an argument about it? Most people would agree that arguing about Frosted Flakes or Rice Krispies is pretty silly. Apply that logic to car audio equipment.

  4. The best equipment is the equipment that you can afford.

  5. X amount of years of experience doesn't mean that you're correct.

  6. 90's and 2000's equipment does not compare to what's currently available. There are some very, very rare exceptions but in general this is the reality of the current technological sandbox that we play in.

  7. Vehicle matters. Application matters. What worked in your vehicle is not the holy grail of cut n paste car audio systems.

  8. Car audio is a science. It's always going to follow the principles of electricity, sound, and electromechanics. That means that your hatchback won't do 20k rms on alternator power alone.

  9. Small subs play lower frequencies. Cone diameter doesn't determine what frequencies it can play.

  10. Nobody makes subwoofers that "pop all the time".


r/CarAudioFacts • • May 07 '24

FYI How to calculate the amount of watts your electrical can support.

9 Upvotes

This is how to get a good estimate of what your electrical can support. Due to the amount of variance in equipment available, this is only considered as a good general practice based on science.

  1. Find out how many amps of power your alternator supplies. You can do this by looking it up online or getting the Vin number and doing a search. If you can't get either, look up your car on advance auto or a similar website and see what the replacement alternator amperage is. Go with the lowest rated one.

  2. Find out the voltage that your alternator operates at. The best way to do this is to use a multimeter set to dc voltage and touch the positive terminal on it with the positive probe and touch the negative probe to a grounded location in the engine bay.

  3. Multiply your alternator output by .6. In general, most cars use about 40% of the alternator power to run. Multiplying by .6 gives you the amount of amperage available to use.

  4. Divide #3 by .7. Most amplifiers operate at 70% efficiency. The rest is converted to heat. Dividing by 0.7 gives you the amount of amperage that will be converted into output power.

  5. Multiply #4 by #2. The result is the highest amount of wattage your system can make.

  6. Multiply 12.6 by #4. This is the general best practice for estimating power output. 12.6 volts is the lowest that you want your system operating at. That's your benchmark.

  7. Divide both numbers by 2. That's because most amplifiers operate at around 50% due to the dynamic nature of music.

Thee answer to #7 is your reference point to refer to when shopping for an amplifier. I'd recommend staying closer to the 12.6 voltage calculation. But as long as you stay between both numbers you should be ok.


r/CarAudioFacts • • May 04 '24

FYI How to calculate the amount of power needed for your amplifier.

8 Upvotes

Here's a good general practice for calculating how much power an amplifier for subwoofers will need.

  1. Check the efficiency rating for the amp at whatever ohm load you're wiring your subwoofers to. Most amplifiers operate at a higher efficiency at higher ohm loads. If you don't know or can't find it, use 70% as a starting point.

  2. Plug the corresponding information into the following equation:

(Amplifier Watts RMS / desired voltage)/ efficiency rating

In English that means divide the rms rating of the amplifier by the voltage number that you'd like to maintain at the lowest.

Then divide that by the efficiency rating.

That will give you the maximum amount of amperage the amplifier needs at that voltage. I'd recommend 12.6 volts at minimum.

Example: 1000 watts RMS amp that operates at 70% efficiency at 12.6 volts.

1000/12.6 = 79.365.

79.365/ 70% = 113.378

So a 1000 watt amp that runs at 12.6 volts will use 113.378 amps of power.

A good amp that puts out more than rated power may use more, but due to the dynamic nature of music, the likelihood that this will ever become an issue is almost nonexistent.

Most amplifiers for mids and tweeters won't use anything close to what a subwoofer amplifier needs unless you're powering PA drivers. That's because subwoofers move a lot more air than mids and tweeters do.

Realistically your subwoofer amplifier will use about 50-70% of that number on average but I always recommend planning an electrical system that can handle the maximum amount of amperage or more. It's always good to have more power than you need than not having enough, or just enough to meet the minimum requirements.


r/CarAudioFacts • • May 18 '24

FYI How to set your gains using Kickers Amplifier Output Voltage Conversion Chart

Post image
6 Upvotes

This is courtesy of Kicker. This quick reference chart can be used with a multimeter to set amplifier gains correctly.

  1. Find your amplifiers RMS rating in the columns.

  2. Look for the ohm rating in the corresponding row.

  3. That's what the output voltage should read.

Here's how to use the output voltage to set gains.

  1. Download a tone generator or find a 40hz tone on YouTube. Make sure it's recorded at 0db (more on that later).

  2. Set all EQ settings to where you want them. This includes bass and treble. The correct number to set all bass booster volumes to is 0.

The correct number to set all bass booster volumes to is 0.

The correct number to set all bass booster volumes to is 0.

0.

3. Turn your head unit up to the highest number that it can go without clipping the signal. If you don't invite what that number is, here's how you find the right number:

A. Take the maximum volume number and cut it in half.

B. Write that number down.

C. Take this new number and cut it in half again.

D. Write that number down.

E. Add the number from B and the number from D together.

4. From this point forward, that's the loudest that you'll ever turn the volume up to on that head unit.

EVER. That includes all bass boosters. Yes, that means they stay at 0 as long as it's in your car.

5. If you have a bass knob, turn it up to max volume unless that will cause it to clip like the head unit. If this is the case, the best place to mount that bass knob is in the trash can. All others should be set to max volume.

6. Disconnect the subwoofer leads from the amplifier.

7. Play the 40hz tone.

8. Set your multimeter to a/c voltage.

9. Touch the positive lead to the positive speaker output and the negative lead to the negative speaker output.

10. Compare the results of the multimeter reading to the output voltage listed on the Kicker output voltage chart.

11. Adjust the gain knob until the multimeter reading matches the output voltage number listed on the Kicker output voltage chart.

12. Pop your collar. Brush that dirt off yo' shoulders. You're done!


r/CarAudioFacts • • May 02 '24

Recommendation Basic upgrade package for around $700

6 Upvotes

Here's a basic upgrade package that will work for most vehicles with 4 6.5-inch speakers. This includes speaker upgrades and a subwoofer enclosure. You'll need to pair a loc or aftermarket radio with rca outs.

This won't beat down the block or anything like that. This is the system that I installed in my friends 2009 Suzuki Grand Vitara, but it can be applied to several vehicles if you're looking for a basic sound quality upgrade with a little bass.

KICKER 43C124-N Bundle with Universal Car Stereo Vented Port Dual 12" Comp C12 Sub Box Enclosure - Final 2 Ohm https://a.co/d/9mHWxTm

Taramps Bass 400 amplifier 400 watts RMS 1 Channel 2 Ohms Monoblock Class D, great for Sub and Bass, Bass Boost, Crossover High/Low Pass, Power technology, Small Amp, White https://a.co/d/81GJelC

Taramps TS 400x4 400 watts RMS 4 Channels Full Range Car Audio Amplifier, 2 Bridged Channels, RCA Input Class D, Output Power, Multichannel Amplifier System, Small https://a.co/d/iiUkZbI

These 6.5-inch components sound awesome and usually are on sale.

https://www.mx-designs.com/2way/mx261.php

These 6.5-inch coaxials are usually on sale and sound great.

https://www.cdtaudio.com/cdtnew22/products/coaxials/hd6keix1.php

Skar Audio 8 Gauge OFC Complete Amplifier Installation Wiring Kit, SKAR8MANL-OFC https://a.co/d/3Mls7jS

BULVACK 2 Way Mini ANL Fuse Holder, Copper 0/2/4 Gauge to 4/6/8 Gauge 60 Amp Fuse Distribution Block for Car Truck Boat Audio Stereo Amplifier https://a.co/d/c31aaAs

Swap the 60 amp fuses for 30 amp fuses.

BNTECHGO 10 Gauge Silicone Wire 10 ft red and 10 ft Black Flexible 10 AWG Stranded Tinned Copper Wire https://a.co/d/2sBikxP

InstallGear 12 Gauge Wire AWG Speaker Wire (100ft - Red/Black) | Speaker Cable for Car Speakers Stereos, Home Theater Speakers, Surround Sound, Radio, Automotive Wire, Outdoor | Speaker Wire 12 Gauge https://a.co/d/56LfFlx

Use the speaker wire for the doors and for the subwoofer enclosure.

This is a recommended general starting point for reference only. Make sure there's enough space for the subwoofer enclosure and that the speakers will fit into the doors or deck. Adding an aftermarket radio will increase the cost obviously, and so will professional installation. Electrical upgrades shouldn't be necessary for most vehicles.

If your head unit is integrated with heating, ac, and other controls, this may not be the best idea for your vehicle.

Wis


r/CarAudioFacts • • May 13 '24

Build Log 2014 ford edge build log

Thumbnail
gallery
4 Upvotes

2014 ford edge: Factory head unit: Rockford Fosgate DSR1

Amps: JL XD400/4 JL XD600/1

Front doors: Focal V20 6.5 Morel Maximo Tweeters Boston Acoustics Pro series Crossovers

Rear Doors: Rockford Fosgate T2625-s

Sub: JL 10” TW3

Sub box =.517CuFt

Full sound treatment on the doors and the rear tail gate, still need to do the trunk area.

All work done by me.


r/CarAudioFacts • • May 03 '24

Recommendation Big bass, small space. 12" subs that require less airspace.

4 Upvotes

A few options for adding bass when space is at a premium. Sorry, no truck enclosures yet, although some of the options listed below may fit. These all fit into ported enclosures by manufacturers recommendation.

Here's a list of 12" Subwoofers that require 1.25 cubic inches of airspace or less.

CT Sounds: All of the following CT Sounds subwoofers require 1 cubic ft of airspace.

Bio 12" 400 watts RMS https://www.ctsounds.com/collections/bio-series-subwoofers/products/bio-12

Tropo 12" 650 watts RMS https://www.ctsounds.com/collections/tropo-subwoofers/products/tropo-12

Ozone 12" 800 watts RMS https://www.ctsounds.com/collections/ozone-subwoofers/products/ozone-12

Tropo XL 12" 1000 watts RMS https://www.ctsounds.com/collections/tropoxl-subwoofers/products/tropo-xl-12

Meso 12" 1500 watts RMS https://www.ctsounds.com/collections/meso-series-subs/products/meso-12

DC Audio: All of these subwoofers require 1.25 cubic ft of airspace.

Level 1 12" 300 watts RMS https://www.dcsoundlab.com/level-1

Level 2 12" 600 watts RMS https://www.dcsoundlab.com/level-2

Level 3 12" 1000 watts RMS https://www.dcsoundlab.com/level-3

Keep in mind that most subs require a very small amount of space behind the magnet for venting.


r/CarAudioFacts • • May 03 '24

Recommendation Box modeling using speakerboxlite and wooferbox pro

Thumbnail
gallery
4 Upvotes

I modeled the subwoofer enclosure with the Speakerboxx Lite website Woofer Box Pro. By using both tools I can double check my measurements, port tuning, port length, subwoofer placement and spl numbers at any frequency.

You'll need the T/S parameters for the subwoofer, an idea of how much space you have available for an enclosure, how much amplifier you plan to use, and how low you'd like your tuning to be.

The box is for 3 DC Audio XL Spl 12-in Subs. As you can see, you'll have access to graphing the driver response, spl numbers, and several other graphs. Speakerboxx lite will allow you to quickly model driver response in different amounts of airspace and at different tuning frequencies.

The cool thing about it is that both are free to use. I've done multiple boxes using both and the results are super. accurate.


r/CarAudioFacts • • Jul 11 '24

Build Log Current build idea for my 2001 Nissan Sentra

Thumbnail
gallery
3 Upvotes

Speakers:

Tweeters: 2 pairs of Stereo Integrity M25 tweeters. Mid-range: 1 set of Morel MSW-424 4" speakers. Mid-bass: 1 set of Morel TIW-634 6" speakers. Rear fill: 1 set of Morel Tempo Ultra Integra 602 6.5 coaxials. Subwoofers: 3 DC Audio XL Spl Elite 12-in Subwoofers 1.4 ohms each, wiredto 0.93 ohms final load. Enclosure: 38 x 28 x 13.5 4.47 cubes net tuned to 30hz. 59.1 inches port area.

Amplifiers:

Tweeters: Helix M4 DSP 4 x 100 watts rms at 4 ohms. Ten channel Helix dsp built in. Mids and Rear: Helix M6 6 x 100 watts rms at 4 ohms. Subwoofer enclosure: NVX XAD16 8K at 1 ohm.

Electrical:

370 amp alternator 148ah Lithium Lev60 battery. Puts out up to 600 amps continuous. One 4/0 100% copper welding cable run from alternator to rear. 3 2/0 100% copper welding cable ground runs to frame.

Head unit: Mekede M7 PRO 10.3" Android unit.

EQ: Clarion EQ 755

Total estimated cost $6500-$7000.

The Mekede M7 PRO plays high resolution Flac files but the Clarion EQ will actually be the control point for volume since it has separate volume knobs for Sub Level and level for the other speakers. Since the dsp is built into the amp it'll eliminate the need for a controller and allow for minor adjustments on the fly.

The enclosure is designed to play down to 20hz, peak at 30hz, and play up to the 150hz range before significant drop off. I'm aiming for Dem Lowz.

Thoughts?


r/CarAudioFacts • • Jun 26 '24

Recommendation Subwoofer help needed

3 Upvotes

Hey everyone, I’m looking at getting 1 or 2 10” subwoofers for my coupe corvette. I have roughly 52 cubic feet of airspace which I know is not a lot. Any advice whether I should do 1 or 2 subs and how much power I should put to them? Any help is appreciated and if I can clear anything up or if I need to go to a different group lmk.

Thanks


r/CarAudioFacts • • May 07 '24

Build Log 2018 GTI Build Log

Thumbnail
imgur.com
3 Upvotes

Here is my finished 2018 GTI stereo!


r/CarAudioFacts • • May 04 '24

Build Log Some more receipts for you. The full build log is on Diymobileaudio.com.

Thumbnail
gallery
3 Upvotes

r/CarAudioFacts • • May 04 '24

Build Log Here's some receipts for you guys. My first build log on Diymobileaudio.com.

Thumbnail
gallery
3 Upvotes

r/CarAudioFacts • • May 02 '24

FYI Tips and tricks for evaluating subwoofers, amplifiers, and speakers for car audio.

3 Upvotes

Here are some general tips and tricks to go by when evaluating what equipment would work for your plan.

  1. Amplifiers:

    A. Ignore max power numbers and claims from manufacturers. RMS power is the correct measure of what the actual output of the amplifier would be.

    B. Before you purchase an amplifier, make sure that your electrical system has enough power to support it. This is not only a good general practice, this can avoid safety issues in the future as well.

    C. Make sure that the ohm rating of the amplifier matches the ohm rating of your subwoofer enclosure. If your subwoofer enclosure has a rating of 1 ohm and your amplifier is rated at 2 ohms, the amplifier can fail due to its inability to provide power at the lower ohm rating.

  2. Subwoofers:

    A. Make sure that you have enough power to support the subwoofer. A 500-watt amplifier and a 2000-watt subwoofer are a bad match. Although underpowering a subwoofer will not harm it, in general, it is a good idea to match the output of the amplifier with the requirements of the subwoofer.

    B. Make sure that you have enough space for the subwoofer enclosure. Every subwoofer has a recommended amount of airspace that it needs to operate efficiently. Make sure that you have the space in your vehicle to accommodate the airspace that the subwoofer needs, as well as the additional space that would be taken up by the materials the enclosure is made out of. Also, make sure to consider things such as port size, subwoofer placement, etc.

    C. Make sure that the final ohm rating of the subwoofers and the amplifier match. There is a sticky post that has a link to the 12 volt website, which has a subwoofer wiring diagram that shows how to wire subwoofers to the ohm rating that you need.

  3. Speakers.

    A. Make sure to check the available depth for factory drop-in speaker locations.

    B. Determine if the speakers will need an amplifier. If your plan is to replace your factory speakers without any further upgrades, make sure that the speakers selected can be driven by your head unit. A 150-watt RMS speaker is not going to sound good driven by a basic head unit. In my opinion, I would stay somewhere around a 50-watt RMS and lower for simple drop-in replacements.

And last but definitely not least, if you're not sure, ask before you buy.

The above information is, in my opinion, a general guide to best practices when planning what amplifiers subwoofers and speakers to purchase for your audio installation. This guide is by no means comprehensive and should be taken as a starting point for doing research into what would work best.


r/CarAudioFacts • • May 02 '24

FYI General Help and Resources

3 Upvotes

How to get the best answer to your question...

https://www.reddit.com/r/CarAudioFacts/s/djok2PFias

How to evaluate amplifiers, subwoofers, and speakers...

https://www.reddit.com/r/CarAudioFacts/s/JkWVeKlm5o

How to plan a system...

https://www.reddit.com/r/CarAudioFacts/s/w0OnegDa5F

The links below will take you to information that will assist in your car audio installs.

Amplifier reviews and dynos:

Big D Wiz has hundreds of amp dynos and reviews. He works with a lot of the major players in the YouTube community.

https://youtube.com/@wal?si=2FaemLoJVfmnVUj7

Bass Dad has a great YouTube channel for amp dynos, interviews, lithium batteries, and all manner of things car audio.

https://youtube.com/@BassDad?si=ma78psRc_VwsDePp

Facekicker has amp dynos and reviews on amps that you may not find on the other channels. This is the unofficial home of Jones Subwoofer Solutions.

https://youtube.com/@Facekicker?si=pSeXzEORDkuRJdhK

Car Audio Fabrication YouTube playlists: The following playlists are a great place to start learning about car audio. Subscribe to the Car Audio Fabrications YouTube channel. It's a great source of information.

For the complete newbie:

https://youtube.com/playlist?list=PLmybwiwzi3MU7VAcm9uyBlm-9SJL3TDta&si=yWGiUtZX6GYBLZxk

Car Audio basics:

https://youtube.com/playlist?list=PLmybwiwzi3MVV6AX5UIcR_0EtiNxDuf2h&si=1sb5RCmsHvPC9e99

Car Audio tutorials:

https://youtube.com/playlist?list=PLmybwiwzi3MUAwm6BuEg3SOlBeaQosHNu&si=Csw8b-Ymgy4Y-mvV

Car audio electrical tutorials:

https://youtube.com/playlist?list=PLmybwiwzi3MVPhGmTqQzRMLJ4GJMx1K9_&si=6qoZFPeE1rzA0bZq

Resonix Sound Solutions is your go-to for premium automotive sound treatment solutions. Here's a beginners guide to sound treatment:

https://resonixsoundsolutions.com/sound-deadening-materials-reference-information/

MB Enclosures is a premier subwoofer enclosure builder. Here's the link to his YouTube channel:

https://youtube.com/@M.B.Enclosures?si=cXD70MjBlkzZ2EJR

The 12 volt is a great online resource for all this car audio. Here are some links to useful pages there.

Subwoofer wiring: https://www.the12volt.com/caraudio/subwoofer-wiring-diagrams.asp

Ohms Law explained:

https://www.the12volt.com/ohm/ohms-law.asp

Ohms Law calculators:

https://www.the12volt.com/ohm/ohms-law-calculators.asp

Power and ground cable sizes:

https://www.the12volt.com/wiring/recommended-car-stereo-wire-sizes.asp

Subwoofer enclosure calculators:

https://www.the12volt.com/caraudio/boxcalcs.asp#rec

T/S parameters explained:

https://www.the12volt.com/caraudio/thiele-small-parameters.asp

DIY Mobile Audio:

The go-to online community for all manner of car audio installations.

Https://Diymobileaudio.com

Speakerboxx lite: Free online tool for designing and modeling subwoofer enclosure and frequency response.

https://speakerboxlite.com/

SubBox.Pro: Free online tool for designing subwoofer enclosures.

https://subbox.pro/en/

If there are any other resources that should be added to this list, please feel free to message the moderator for review and addition.


r/CarAudioFacts • • Jul 12 '24

Recommendation I’m looking for a single 12” or 15” sub budget is 400 what can get me the best bang for my buck

2 Upvotes

r/CarAudioFacts • • Jun 15 '24

Recommendation Do any amps support video output for nav

2 Upvotes

I have a 2007 max with factory nav that has a big nav screen much higher and easier to see while driving which is really nice for directions. I found a composite adapter for this screen but most head units I see only support video output for rear passengers. I want a head unit with composite output that mirrors whatever is on the CarPlay display, particularly while in Apple/google maps, but also ideally in Spotify so I do not have to look downwards. Thanks in advance! I prefer pioneer and Sony if possible


r/CarAudioFacts • • Jun 12 '24

Recommendation I’m looking to see what’s the best budget battery? I have 2 alpine 12’s on a 3000 watt amp.. looking to see what’s a good battery..

2 Upvotes

r/CarAudioFacts • • Jun 08 '24

Recommendation Need help

Thumbnail
gallery
2 Upvotes

I got this amp for free and I don't know how to get this out I need help this is my first time


r/CarAudioFacts • • May 09 '24

FYI Spl/Db calculator

2 Upvotes

This is a link to a decibel calculator that's pretty good for what I've been able to find.

http://www.hometheaterengineering.com/splcalculator.html


r/CarAudioFacts • • May 09 '24

FYI Car Audio Sound System Secrets

2 Upvotes

https://abtec.co.nz/blog/car-audio-sound-system-secrets/

This is a great read that touches on almost every aspect of car audio acoustical theory. This isn't a scientific article and the writer does express his opinion in funny ways. There is a lot of legitimate information though. I'd recommend anyone new to the culture give this a read. If you have questions feel free to DM me. I'm always happy to help thank you.


r/CarAudioFacts • • May 07 '24

FYI Everyone can post now my apologies.

2 Upvotes

I made a mistake with the settings, but it's fixed now. If something isn't working right, please let me know. I'm new to this subreddit managing thing, and I'm bound to make mistakes. I appreciate any and all constructive feedback.


r/CarAudioFacts • • May 02 '24

FYI How to plan your car audio system

2 Upvotes

Every car audio the system installation, no matter the size or complexity, requires the following basics in order to effectively plan for and achieve the desired results.

  1. Your budget. This the most important part of the planning process. Your budget determines the size of your build, the complexity of your build, and the quality of the components that will be part of your build. There is no such thing as a good budget or a bad budget. And there are options for budgets of every size.

  2. Your vehicle. The make and model of your vehicle is important for determining what components will work best. What sounds good in a Suburban can be very different from what sounds good in a Civic.

  3. Your end goal. Upon completion of the installation process how do you visualize your new system sounding? Are you looking to add Bass, improve sound quality, volume, or a mixture of the three?

  4. Available space. This is crucial for determining the size of subwoofer enclosures, what speakers will fit in what location inside the vehicle, and what system of speakers will work best, All Things Considered.

  5. Electrical capacity. The amount of power available to use for your system is important in determining the size, scope, and complexity of your install. Larger Vehicles tend to have more power available without modification than smaller vehicles. There are exceptions to the rule, but this is generally true.

In my personal opinion, all of the above should be answered prior to purchasing products of any kind for the upgrade.


r/CarAudioFacts • • Sep 24 '24

FYI Taking a break from reddit

Thumbnail reddit.com
1 Upvotes

r/CarAudioFacts • • Sep 21 '24

Recommendation finally got the last of the parts ,,amp wiring kit and speaker wire Spoiler

1 Upvotes

-T-Spec V10-AK11/0-gauge amplifier wiring kit — includes power wiring and 2-channel patch cable

-Stinger PRO Series Speaker WirePriced per foot (12 Gauge)

do i have to get these wire teerminals?????

-Accele Speaker Wire TerminalsFour 0.25" quick disconnects for 10- to 14-gauge speaker wire (Black)

 Remove item

 Save for later

Stinger PRO Series Speaker Wire

 Remove item

 Save for later

Stinger PRO Series Speaker Wire